display CADILLAC DEVILLE 2002 8.G Workshop Manual

3-3
!~(Fan): This switch adjusts the fan speed. Press the
up arrow to increase fan speed and the down arrow to
decrease it.
(Recirculation): Press this button to limit the
amount of outside air entering your vehicle. This is
helpful when you are trying to cool the air quickly or
limit odors entering your vehicle. Press this button again
to turn off the recirculation feature. If you notice the
windows fogging, turn off the recirculation feature.
Recirculation is not available in the defrost mode.
FRONT (Defrost): Press this button to quickly
remove fog or frost from the windshield. This setting
sends most of the airflow to the windshield with only a
small amount to the floor outlets. The air conditioning
compressor will operate in this mode.
A/C (Air Conditioning): Press this button to turn the
air conditioning compressor on and off. The system will
cool and dehumidify the air inside the vehicle. A/C
cannot be turned off in defrost mode.PASS OFF (Passenger's Climate Control): Pressing
this button will turn off or on the climate controls for the
passengers. When this feature is active, the driver's
climate control settings are used for both the front and
rear seating areas.
Driver's Temperature Knob: The knob located on the
left side of the climate control panel is used to adjust the
air temperature coming through the system for the
driver's side of the vehicle while the passenger's side
controls are active. Turn the knob clockwise to increase
the temperature displayed on the climate control panel,
or turn the knob counterclockwise to decrease the
temperature. Press the knob to turn the climate control
system off.
~PASS TEMP! (Passenger's Temperature): This
switch is used to increase or decrease the temperature of
the air for the right front passenger independent of the
driver's setting.
Press the up arrow to increase the temperature setting or
the down arrow to decrease it.

3-4
Automatic Operation
AUTO: This button is used to select the automatic
operation of the climate control system. When the
automatic operation is active, AUTO will appear on
the display.
A sensor will control the air delivery mode. Air will
come from the floor, the instrument panel or windshield
outlets. The fan speed and use of air conditioning
will vary as the system maintains the selected
temperature setting.
Do not cover the electronic solar sensor located on top
of the instrument panel near the windshield. The sensor
is used by the automatic system to regulate temperature.
See ªElectronic Solar Sensorº later in this section for
more information.
To find your comfort zone, start with the 75
F (24
C)
setting and allow about 30 minutes for the system to
regulate. Turn the driver's temperature knob to adjust
the temperature if necessary. If you choose 60
F
(16
C), the system will remain at that maximum cooling
setting and will not regulate fan speed. If you choose
90
F (32
C), the system will remain at that maximum
heating setting and will not regulate fan speed. Choosing
either maximum setting will not cause the system to heat
or cool any faster.In cold weather, when the system senses the need for
heat, the airflow will be directed out of the floor outlets.
As the interior temperature approaches the desired
setting, the fan speed will decrease. To maintain interior
comfort, the airflow may move to the instrument panel
air outlets and floor outlets (bi
-level mode). On bright
sunny days in cold weather, the airflow may come out of
the instrument panel outlets in A/C mode to maintain
comfort and prevent stuffiness.
When the automatic setting is active, the air
conditioning compressor cycles when needed to cool the
air. If your vehicle is sitting out on a hot day and AUTO
is active, the air will first flow out of the floor outlets for
a few seconds. This is normal. This is to remove hot air
from the air outlets. As the air is cooled, the airflow will
move through the instrument panel outlets. If you start
your vehicle with the fan setting on HI, it will skip the
air conditioning purge and the system will be in
manual mode.

3-8 Rear Climate Control
Your vehicle is equipped with a rear climate control.
With this system, the rear passengers can control the
temperature of the air flow for his/her own zones.The rear climate control has three switches:
~ MODE !: Press this switch to select the direction
of the airflow. Press the up or down arrow to cycle
through the available modes. The current mode appears
on the display above the climate control panel. If you
press the down arrow until AUTO is displayed,
automatic mode will be active. The automatic mode
selects the airflow mode for you.
See ªManual Operationº previously in this section for
more information on the modes available.
!
~
(Fan): Press this switch to manually adjust the fan
speed. Press the up arrow to increase the speed or the
down arrow to decrease it. The current speed will appear
on the display above the climate control panel. You can
turn the system off by pressing the down arrow until
OFF appears on the display.

3-9
~ TEMP ! (Temperature): Press this switch to
manually adjust the temperature. Press the up arrow to
increase the temperature or the down arrow to decrease
it. The current temperature will appear on the display
above the climate control panel.
The front seat climate control panel has an AUTO
button that can override the climate controls of the rear
seating area automatically. When AUTO is pressed, the
rear automatic mode is selected and the rear air
temperature and mode will readjust to coincide with the
setting selected for the front seating area.
The PASS OFF button on the front climate control panel
allows the settings for the driver to be used for the front
and rear seat areas.Ventilation System
Your vehicle's flow-through ventilation system supplies
outside air into the vehicle when it is moving. Outside
air will also enter the vehicle when the heater or the air
conditioning fan is in operation. See ªRecirculationº
listed previously in this section for more information.
The front outlets are located in the center and at each
side of the instrument panel. You can adjust the
direction of airflow by moving the center control levers
or you can stop the airflow by moving the thumbwheel
located on each outlet downward.

3-12
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off. See
ªRetained Accessory Powerº in the Index.
Setting the Clock
Press and hold HR or MN until the time display begins
to change. Release the button as you get close to the
correct time. The time may be set anytime the clock is
displayed. There is a two
-second delay before the clock
goes into time
-set mode.
AM-FM Stereo with Cassette Tape and
Compact Disc Player
Playing the Radio
PWR (Power): Press this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing one of these buttons.

3-13
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.
Finding a Station
BAND: Press this button to select AM, FM1 or FM2.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds
to scan radio stations and associated tone settings.
The radio will go to a station, play for five seconds,
then go on to the next station. Press this button again
to stop scanning.To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2), by performing the
following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds until you hear a beep.
5. Repeat the steps for each pushbutton. Whenever
you press that numbered pushbutton for less than
two seconds, the station you set will return.
When battery power is removed and later applied, you
will not have to reset your radio presets because the
radio remembers them.

3-14
Setting the Tone (Bass/Treble)
TONE: Press and release this button until the desired
tone control (bass, treble or midrange) is found. The
radio keeps separate tone settings for each band, each
preset and each source.
- LEVEL +: After selecting the desired tone control,
press the plus or minus symbol on this button to select
the desired level.
To save the tone settings for your presets, press and hold
the numbered pushbutton for the desired preset for more
than two seconds until you hear a beep.
Adjusting the Speakers (Balance/Fade)
(Speaker): Press and release this button until the
desired control (balance or fade) is found.
- LEVEL +: After selecting the desired control, press
the plus or minus symbol on this button to select the
desired level.
PTY (Program
-Type): This button is inoperable on
this radio.Playing a Cassette Tape
With the radio on, insert a cassette tape. The tape will
begin playing as soon as it is inserted. When one side of
your cassette tape is done playing, auto reverse plays the
other side of your cassette tape. A cassette tape may be
loaded with the radio off but it will not start playing
until the radio is on. If you want to insert a cassette tape
when the ignition is off, first press the eject button.
While the tape is playing, use the VOL, TONE, LEVEL,
and speaker controls just as you do for the radio. Other
controls may have different functions when a tape is
inserted. The display will show an underlined tape
symbol. TAPE PLAY will appear on the display when a
tape is playing, with an arrow to indicate which side of
the tape is playing.
Your cassette tape player automatically reduces
background noise. Dolby Noise Reduction is manufactured
under a license from Dolby Laboratories Licensing
Corporation. Dolby and the double
-D symbol are
trademarks of Dolby Laboratories Licensing Corporation.
Auto CrO
2 allows the cassette tape player to adjust to
the type of cassette tape for clearer sound for CrO
2cassette tapes.
If an error appears on the display, see ªCassette Tape
Messagesº later in this section.

3-15

RW (Rewind): Press the left arrow to rewind the
tape rapidly. The radio will play while the tape rewinds.
You may use your station pushbuttons to tune to another
radio station while in rewind. Press the left arrow again
to return to playing speed.
FF
 (Fast Forward): Press the right arrow to fast
forward to another part of the tape. The radio will play
while the tape advances. You may use your station
pushbuttons to tune to another radio station while in fast
forward. Press the right arrow again to return to playing
speed.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button to listen to selections for a few
seconds. The tape will go to a selection, play for a few
seconds, then go on to the next selection. Press this
button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing.
(Eject): Press this button to the right of the
cassette tape player to remove a tape. The radio will
play. Eject may be activated with the radio off and/or
the ignition off.
Cassette Tape Messages
If an error occurs while trying to play a cassette tape, it
could be for one of the following reasons:

The cassette tape is tight and the cassette player
cannot turn the hubs of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with a pencil. Flip the tape
over and repeat. If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used in the player. Try a new tape to be sure your
player is working properly.

The cassette tape is broken. (Check to see if your
tape is broken. Try a new tape.)
CLEAN TAPE: If this message appears on the display,
the cassette tape player needs to be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer.

3-16
Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in. If the ignition and the radio are on
and the underlined compact disc symbol appears on the
display, the disc will begin playing. Compact discs may
be loaded with the radio off but they will not start
playing until the radio is on. If you want to insert a disc
when the ignition is off, first press the eject button.
The integral CD player can play the smaller 8 cm
compact discs. Full
-size compact discs and the smaller
compact discs are loaded in the same manner.
If an error appears on the display, see ªCompact Disc
Messagesº later in this section.

RW (Rewind): Press and hold the left arrow to
reverse the compact disc. Release it to return to playing
speed.
FF
 (Fast Forward): Press and hold the right arrow
to fast forward to another part of the compact disc.
Release it to return to playing speed.
~' TUNE SEEK !': When this button is pressed, it
has two positions. This button works the same, whether
it is pressed to the first or second position. Press this
button to seek to the next or previous track on the
compact disc.
SCAN: Press this button to listen to tracks for a few
seconds. The compact disc will go to a track, play for a
few seconds, then go on to the next track. Press this
button again to stop scanning.
RDM (Random): Press this button to hear the tracks in
random, rather than sequential, order. Press RDM again
to turn off random play.
(Eject): Press this button, located to the right of the
CD slot, to stop a CD when it is playing or to eject a CD
when it is not playing. Eject may be activated with the
radio off and/or the ignition off.

3-18
AVC (Automatic Volume Control): With AVC, your
audio system monitors the noise in the vehicle. Then,
AVC adjusts the volume level so that it always sounds
the same to you. To use AVC, press and hold the TONE
button until AUTO VOLUME CONTROL OFF appears
on the display. Then press the LEVEL plus symbol.
AUTO VOLUME CONTROL ON will appear on the
display. AVC VOLUME will appear on the display any
time you adjust the volume while AVC is on. To turn
AVC off, press and hold the TONE button until AUTO
VOLUME CONTROL ON appears on the display. Then
press the LEVEL minus symbol. AUTO VOLUME
CONTROL OFF will appear on the display.
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing one of these buttons.
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.Finding a Station
BAND: Press this button to select AM, FM1 or FM2,
weather or XM1 or XM2 if your radio is equipped with
XM
Satellite Radio Service.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds to
scan radio stations. The radio will go to a station, play
for five seconds, then go on to the next station. Press
this button again to stop scanning.
To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.