windshield wipers CADILLAC DTS PROFESSIONAL 2007 1.G Owners Manual

Ignition Positions
With the ignition key in the ignition, the key can be
turned to four different positions:
Notice:Using a tool to force the key from the
ignition switch could cause damage or
break the key. Use the correct key and turn the
key only with your hand. Make sure the key
is in all the way. If none of this works,
then your vehicle needs service.A (OFF):This is the only position in which the
ignition key can be inserted or removed. This
position locks the ignition and transaxle. It is a
theft-deterrent feature.
B (ACCESSORY):This position lets the radio and
windshield wipers operate while the engine is
off. To use ACCESSORY, turn the key clockwise.
C (RUN):This position is where the key returns
to after the vehicle is started. This position displays
some of the warning and indicator lights.
The battery could be drained if you leave the key
in the ACCESSORY or RUN position with the
engine off. You may not be able to start your
vehicle if the battery is allowed to drain for
an extended period of time.
D (START):This position starts the engine.
A warning chime will sound and the Driver
Information Center (DIC) will display DRIVER
DOOR OPEN when the driver’s door is opened if
the ignition is in OFF, ACCESSORY and the
key is in the ignition. SeeDIC Warnings
and Messages on page 246for more information.
118

Instrument Panel Overview........................ 162
Hazard Warning Flashers.......................... 164
Other Warning Devices............................. 164
Horn.......................................................... 164
Tilt Wheel.................................................. 165
Power Tilt Wheel and Telescopic
Steering Column.................................... 165
Heated Steering Wheel............................. 166
Turn Signal/Multifunction Lever.................. 166
Turn and Lane-Change Signals................. 167
Headlamp High/Low-Beam Changer.......... 167
Forward Collision Alert (FCA) System........ 168
Flash-to-Pass............................................ 172
Windshield Wipers..................................... 172
Rainsense™ II Wipers............................... 173
Windshield Washer.................................... 175
Cruise Control........................................... 176
Adaptive Cruise Control............................. 179
Exterior Lamps.......................................... 193
Wiper Activated Headlamps....................... 197
Headlamps on Reminder........................... 197
Daytime Running Lamps (DRL)................. 197Fog Lamps................................................ 198
Cornering Lamps....................................... 199
Exterior Lighting Battery Saver.................. 199
Instrument Panel Brightness...................... 199
Courtesy Lamps........................................ 199
Entry Lighting............................................ 200
Parade Dimming........................................ 200
Reading Lamps......................................... 200
Battery Load Management......................... 200
Electric Power Management...................... 201
Inadvertent Power Battery Saver............... 202
Battery Run-Down Protection..................... 202
Ultrasonic Front and Rear Parking
Assist (UFRPA)...................................... 202
Accessory Power Outlet(s)........................ 208
Ashtray(s) and Cigarette Lighter................ 209
Analog Clock............................................. 210
Climate Controls......................................... 210
Dual Climate Control System..................... 210
Outlet Adjustment...................................... 217
Rear Climate Control System.................... 218
Passenger Compartment Air Filter............. 220
Section 3 Instrument Panel
159

Heated Steering Wheel
Your vehicle may have a heated steering wheel.
The button for this
feature is located on the
steering wheel.
Press the button to turn the heated steering wheel
on or off. A light on the button will display while
the feature is turned on.
The steering wheel will take about three minutes
to start heating.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. See
Turn and Lane-Change Signals on page 167.
3Headlamp High/Low-Beam Changer.
SeeHeadlamp High/Low-Beam Changer
on page 167.
Flash-To-Pass Feature. SeeFlash-to-Pass on
page 172.
NWindshield Wipers. SeeWindshield
Wipers on page 172.
LWindshield Washer. SeeWindshield
Washer on page 175.
_Heated Washer Fluid. SeeWindshield
Washer on page 175.
166

Cleaning the System
The radar can become blocked by snow, ice, or
dirt. If so, you may need to turn off the engine
and clean the lens. See “Cleaning the System”
underAdaptive Cruise Control on page 179.
Flash-to-Pass
This feature lets you use the high-beam
headlamps to signal the driver in front of
you that you want to pass.
The ash-to-pass feature will only work with the
headlamps on. It does not work with Daytime
Running Lamps (DRL).
Pull and hold the turn signal lever toward you
to use.
If the headlamps are on high beam, they will
switch to low beam. To return to high beam,
push the lever away from you.
Windshield Wipers
You control the windshield wipers by turning the
band with the wiper symbol on it.
8(Mist):Turn the band to mist for a single
wiping cycle. Hold it there until the wipers start.
Then let go. The wipers stop after one wipe.
For more wipe cycles, hold the band longer
on mist.
6(Delay):Turn the band to choose the delay time
between wipe cycles. The wiper speed can be set
for a long or short delay between wipes. The closer
the band is set to the top of the lever, the shorter
the delay.
6(Low Speed):Turn the band away from
you to the rst solid band past the delay settings
for steady wiping at low speed.
1(High Speed):For high-speed wiping, turn
the band further, to the second solid band past the
delay settings.
9(Off):To stop the wipers, move the band to off.
172

Clear ice and snow from the wiper blades before
using them. If they are frozen to the windshield,
carefully loosen or thaw them. If the blades
become worn or damaged, replace with new
blades or blade inserts.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools.
Clear away snow or ice to prevent an overload.
Your vehicle has wiper-activated headlamps.
After the windshield wipers have completed eight
wipe cycles within four minutes, the headlamps
automatically turn on. SeeWiper Activated
Headlamps on page 197for more information.Rainsense™ II Wipers
If your vehicle has this feature, the moisture
sensor is mounted on the interior side of the
windshield behind the rearview mirror. It is used
to automatically operate the wipers by monitoring
the amount of moisture build-up on the windshield.
Wipes occur as needed to clear the windshield
depending on driving conditions and the sensitivity
setting. In light rain or snow, fewer wipes will occur.
In heavy rain or snow, wipes will occur more
frequently. The Rainsense™ II wipers operate in
a delay mode as well as a continuous low or high
speed as needed. If the system is left on for long
periods of time, occasional wipes may occur
without any moisture on the windshield. This is
normal and indicates that the Rainsense™ II
system is activated.
173

The Rainsense™ II system can be activated by
turning the wiper band to one of the ve sensitivity
levels indicated on the wiper stalk. The position
closest to off is the lowest sensitivity setting, level
one. This allows more rain or snow to collect on the
windshield between wipes. Turning the wiper band
away from you to higher sensitivity levels increases
the sensitivity of the system and frequency of
wipes. The highest sensitivity setting, level ve is
closest to low. A single wipe will occur each time
you turn the wiper stalk to a higher sensitivity level
to indicate that the sensitivity level has been
increased.
Notice:Going through an automatic car wash
with the wipers on can damage them. Turn
the wipers off when going through an
automatic car wash.The mist and wash cycles operate as normal and
are not affected by the Rainsense™ II function.
The Rainsense™ II system can be overridden at
any time by manually turning the wiper band to low
or high speed.
When Rainsense™ II is active, the headlamps
will turn on automatically. The headlamps will
turn off again once the wipers turn off if it is light
enough outside. If it is dark, they will remain
on. SeeWiper Activated Headlamps on page 197
for more information.
Notice:Do not place stickers or other items
on the exterior glass surface directly in front of
the moisture sensor. Doing this could cause
the moisture sensor to malfunction.
174

Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
J(Washer Fluid):Press and release
this paddle, located at the top of the turn
signal/multifunction lever, to spray washer
uid on the windshield. The wipers will clear
the windshield and either stop or return to your
preset speed. For more washer cycles, press
and hold the paddle.
_(Heated Washer Fluid):The heated
windshield washer uid system, if your vehicle
has this feature, may be used to help clear
ice, snow, tree sap, or bugs from your windshield.Sliding the switch on the turn signal/multifunction
lever to this position and then releasing it will
activate the heated windshield washer uid
system. This activation will initiate four heated
wash/wipe cycles. The rst heated wash/wipe
cycle may take up to 40 seconds to occur,
depending on outside temperature. After the rst
wash/wipe cycle, it may take up to 20 seconds
for each of the remaining cycles. The heated
windshield washer uid system may be turned off
at any time by sliding the switch on the turn
signal/multifunction lever to this position again.
When the heated windshield washer uid system
is activated under certain outside temperature
conditions, steam may ow out of the washer
nozzles for a short period of time before washer
uid is sprayed. This is a normal condition.
WASHER FLUID LOW ADD FLUID will be
displayed on the Driver Information Center (DIC)
when the washer uid is low. SeeDIC Warnings
and Messages on page 246.
175

Wiper Activated Headlamps
This feature activates the headlamps and parking
lamps after the windshield wipers are turned
on and have completed eight wipe cycles within
four minutes.
When the ignition is turned to OFF, the
wiper-activated headlamps immediately turn off.
The wiper-activated headlamps also turn off if the
windshield wipers are turned off.
Headlamps on Reminder
A warning chime will sound if the exterior lamp
control is left on in either the headlamp or parking
lamp position and the driver’s door is opened
with the ignition off.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.
The DRL system will make the turn signal lamps
come on when the following conditions are met:
It is still daylight and the ignition is on.
The exterior lamp control is in the off position.
The transaxle is not in PARK (P)
(United States only).
The light sensor is covered or not detecting
light. See “Sensors” underDual Climate Control
System on page 210.
When DRL are on, no other exterior lamps such as
the parking lamps, taillamps, etc. will be on when
the DRL are being used. Your instrument panel will
not be lit up either.
197

The vehicle has a “basecoat/clearcoat” paint
nish. The clearcoat gives more depth and gloss
to the colored basecoat. Always use waxes
and polishes that are non-abrasive and made for a
basecoat/clearcoat paint nish.
Foreign materials such as calcium chloride and
other salts, ice melting agents, road oil and
tar, tree sap, bird droppings, chemicals from
industrial chimneys, etc., can damage the vehicle’s
nish if they remain on painted surfaces. Wash
the vehicle as soon as possible. If necessary, use
non-abrasive cleaners that are marked safe for
painted surfaces to remove foreign matter.
Exterior painted surfaces are subject to aging,
weather, and chemical fallout that can take their
toll over a period of years. To help keep the
paint nish looking new, keep the vehicle in a
garage or covered whenever possible.
Protecting Exterior Bright Metal Parts
Bright metal parts should be cleaned regularly to
keep their luster. Washing with water is all
that is usually needed. However, you may use
chrome polish on chrome or stainless steel trim, if
necessary.Use special care with aluminum trim. To avoid
damaging protective trim, never use auto or
chrome polish, steam or caustic soap to clean
aluminum. A coating of wax, rubbed to high polish,
is recommended for all bright metal parts.
Windshield and Wiper Blades
Clean the outside of the windshield with
glass cleaner.
Clean the rubber blades using a lint free cloth or
paper towel soaked with windshield washer uid or
a mild detergent. Wash the windshield thoroughly
when cleaning the blades. Bugs, road grime,
sap, and a buildup of vehicle wash/wax treatments
may cause wiper streaking. Replace the wiper
blades if they are worn or damaged.
Wipers can be damaged by:
Extreme dusty conditions
Sand and salt
Heat and sun
Snow and ice, without proper removal
445

Electrical System
Add-On Electrical Equipment
Notice:Do not add anything electrical to your
vehicle unless you check with your dealer
rst. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Add-on equipment can drain your vehicle’s battery,
even if your vehicle is not operating.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, seeServicing Your Airbag-Equipped
Vehicle on page 86.
Headlamp Wiring
The headlamp wiring system has four individual
fuses. An electrical overload will cause the
lamps to go on and off, or in some cases to remain
off. If this happens, have the headlamp wiring
checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an
internal circuit breaker. If the wiper motor overheats
due to heavy snow, the wipers will stop until the
motor cools and will then restart.
A fuse powers the wiper motor. If the fuse blows,
there is an electrical problem. Be sure to have
it xed.
451