mirror CADILLAC ELDORADO 2002 10.G Owners Manual

1-3 Power Lumbar Control (Option)
If your vehicle has this
option, the driver's and
passenger's controls are
located on the outboard
sides of the seat cushions.The power lumbar support control can be adjusted the
following ways:

To increase or decrease support, hold the control
forward or rearward.

To move the lumbar up and down, hold the control
up or down.
Keep in mind that as your seating position changes,
as it may during long trips, so should the position of
your lumbar support. Adjust the seat as needed.
If you have the optional personalization package, the
power lumbar control can be programmed for memory
recall. For more information, see ªMemory and
Personalization Featuresº and ªMemory Seat and
Mirrorsº in the Index.

1-4 Memory Seat and Mirrors (If Equipped)
If your vehicle has this
feature, the controls are
located on the driver's
door armrest.
These buttons are used to program and recall memory
settings for the driver's seating and outside rearview mirror
positions. Use the following steps to program each button:
1. Adjust the driver's seat (including lumbar adjustments)
and both outside mirrors to a comfortable position.
2. Press the SET button.
3. Within five seconds, press button 1. A single beep
will sound through the driver's side front speaker to
let you know that the position has been stored.A second mirror and seating position may be
programmed by repeating the above steps and pressing
button 2 instead of button 1. Each time button 1 or 2 is
pressed and released while the vehicle is in PARK (P),
the memory position will be recalled. Each time a
memory button is pressed, a single beep will sound.
You can also recall a seat and mirror position if your
vehicle is not in PARK (P). Press and hold either
the 1 or 2 button until seat and mirror movement is
complete. Releasing the buttons will stop adjustment.
If you use the button with the unlock symbol on the
remote keyless entry transmitter to enter the vehicle, the
preset driver's seat and mirror positions will be recalled.
The numbers on the back of the transmitters, 1 or 2,
correspond to the numbers on the driver's armrest.
If the remote keyless entry transmitter was not used to
enter the vehicle, the last used seat and mirror positions
will be recalled when a key is inserted in the ignition
and is turned to RUN. The vehicle must be previously
programmed to turn this feature on. See ªMemory and
Personalization Featuresº in the Index.

1-5
To stop recall movement of the memory feature at
any time, press one of the power seat controls or
memory buttons.
The EXIT button can be programmed to allow easy exit
for up to two drivers. Adjust the seat to a comfortable
ªexitº position and then press the SET button followed
by the EXIT button. While your vehicle is in PARK (P),
briefly press the EXIT button to recall your programmed
exit position.
Further programming for automatic seat and mirror
movement can be done using the Driver Information
Center (DIC). You can select or not select the following:

Automatic seat and mirror movement when the
vehicle is unlocked with the remote keyless entry
transmitter, or

automatic seat and mirror movement when a key
is placed in the ignition.
For programming information, see ªMemory and
Personalization Featuresº in the Index.Heated Front Seat (Option)
The switch for the heated
front seat is located in the
center console.
Move the switch to LO or HI to turn on the heating
elements in the seat. The LO setting warms the
seatback and cushion until the seat approximates body
temperature. The HI setting heats the seat to a slightly
higher temperature.
A light in the switch is on when the system is in use.
The heated seats can only be used when the ignition
is turned on.
To turn the heated front seat off, move the switch to
the center position.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-8 Remote Keyless Entry System
2
-12 Trunk
2
-15 Theft
2
-16 Theft-Deterrent System
2
-18 PASS-Key
II
2
-19 New Vehicle ªBreak-Inº
2
-19 Ignition Positions
2
-21 Starting Your Engine
2
-22 Engine Coolant Heater (If Equipped)
2
-24 Automatic Transaxle Operation
2
-27 Parking Brake
2
-29 Shifting Into PARK (P)
2
-31 Shifting Out of PARK (P)
2
-31 Parking Over Things That Burn2
-32 Engine Exhaust
2
-32 Running Your Engine While You're Parked
2
-33 Tilt Wheel
2
-34 Turn Signal/Multifunction Lever
2
-42 Exterior Lamps
2
-46 Interior Lamps
2
-48 Mirrors
2
-51 Storage Compartments
2
-53 Sun Visors
2
-54 OnStar
System (If Equipped)
2
-57 Sunroof (Option)
2
-58 HomeLink
Transmitter (Option)
2
-62 The Instrument Panel -- Your
Information System
2
-66 Warning Lights, Gages and Indicators
2
-78 Driver Information Center (DIC)

2-10
(Unlock): When you press the button with
the unlock symbol on it to unlock the driver's door,
the parking lamps on your vehicle will flash twice.
You can program your vehicle so the parking lamps
will not flash. For more information, see ªLock/Unlock
Confirmationº in the Index.
Pressing the button with the unlock symbol on it again
within five seconds will unlock the other doors. Pressing
this button will also disarm the theft
-deterrent system
and turn on the interior lamps at night.
(Fuel Door): Press the button with the fuel door
symbol on it to open the fuel door. The VALET lockout
button must be off for this feature to work.
(Trunk): Press the button with the trunk symbol
on it to open the trunk. The VALET lockout button
must be off for this feature to work.
The remote keyless entry transmitter can also be
used to recall the memory seats for up to two drivers.
For more information, see ªMemory Seat and Mirrorsº
in the Index.
Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.
Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about four years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it's probably time to change the battery.

2-37 Rainsense
Wipers (ETC Only)
The moisture sensor is mounted on the interior side
of the windshield behind the rearview mirror and is used
to automatically operate the wipers by monitoring the
amount of moisture build
-up on the windshield.
Wipes occur as needed to clear the windshield
depending on driving conditions and the sensitivity
setting. In light rain or snow, fewer wipes will occur. In heavy rain or snow, wipes will occur more frequently.
The Rainsense wipers operate in a delay mode as well as
a continuous low or high speed as needed. If the system
is left on for long periods of time, occasional wipes
may occur without any moisture on the windshield.
This is normal and indicates that the Rainsense system
is activated.
The Rainsense system can be activated by turning the
wiper stalk to one of the five sensitivity levels within the
AUTO DELAY area. The AUTO DELAY position
closest to OFF is the lowest sensitivity setting,
level one. This allows more rain or snow to collect on
the windshield between wipes. Turning the stalk away
from you to the higher levels of other AUTO DELAY
settings increases the sensitivity of the system and
frequency of wipes. The highest sensitivity setting,
level five is closest to LO. A single wipe will occur each
time you turn the wiper stalk to a higher sensitivity level
to indicate that the sensitivity level has been increased.
An initial wipe occurs when you turn the ignition on
as a reminder that Rainsense is active.

2-48
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass and OnStar

Your vehicle has an electrochromic inside rearview mirror
with a compass. Your vehicle's mirror also contains
OnStar

buttons. For more information about OnStar,
see ªOnStarº in the Index.
The mirror also includes an eight
-point compass display
in the upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is driven.
(On/Off): This is the on/off button, located on the
lower left side of the mirror for the electrochromic and
compass functions of the rearview mirror.Mirror Operation
To turn on the automatic dimming feature, press and hold
the on/off button for about three seconds. To turn off
automatic dimming, press and hold the on/off button for
about three seconds again. The green indicator light will
be illuminated when this feature is active. The automatic
dimming feature will be active each time the vehicle
is started.
Compass Operation
Press the on/off button once to turn the compass
on or off.
When the ignition and the compass feature are on,
the compass will show two character boxes for
approximately two seconds. After two seconds,
the mirror will display the compass heading.
Compass Calibration
If after two seconds, the display does not show a
compass heading (N for North, for example), there may
be a strong magnetic field interfering with the compass.
Such interference may be caused by a magnetic antenna
mount, magnetic note pad holder or a similar magnetic
item. If the letter C should ever appear in the compass
window, the compass may need calibration.

2-49
The mirror can be calibrated by driving the vehicle in
circles at 5 mph (8 km/h) or less until the display
reads a direction.
The compass can be placed in calibration mode by
pressing and holding the on/off button until a C is
shown in the compass display.
Compass Variance
The mirror is set in zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, as during a long distance
cross
-country trip, it will be necessary to adjust for
compass variance. Compass variance is the difference
between earth's magnetic north and true geographic
north. If not adjusted to account for compass variance,
your compass could give false readings.
To adjust for compass variance, do the following:
1. Find your current location and variance zone number
on the following zone map.
2. Press and hold the on/off button until a zone number
appears in the display.
3. Once the zone number appears in the display,
press the on/off button quickly until the correct
zone number appears in the display. Stop pressing
the button and the mirror will return to normal
operation. If C appears in the compass window,
the compass may need calibration. See ªCompass
Calibrationº explained previously.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause the
liquid cleaner to enter the mirror housing.

2-50 Power Remote Control Mirrors
The control on the driver's
door armrest operates both
outside rearview mirrors.
Press (R) on the selector switch to choose the right
mirror or (L) to choose the left mirror. The center
position is off and will not move the mirrors if the
control pad is touched.
To adjust the mirror, press the arrows on the control pad
in the direction you want the mirror to go. Adjust each
mirror so you can see the side of your vehicle and the
area behind your vehicle.
The mirrors can also be programmed for personalization
if you have the optional memory package. For more
information, see ªMemory Seat and Mirrorsº in the Index.
Driver's Outside Auto-Dimming
Rearview Mirror
Only the driver's side outside mirror will adjust for
the glare of headlamps behind you. This feature
is controlled by the on and off settings on the
electrochromic mirror. See ªElectrochromic Day/Night
Rearview Mirror with Compassº in the Index.
Curb View Assist Mirror (If Equipped)
If your vehicle is equipped with memory mirrors,
it will also be equipped with the curb view assist mirror
feature. This feature will cause the passenger's mirror
to tilt when the vehicle is moving in REVERSE (R).
This feature may be useful in allowing you to view the
curb when you are parallel parking. To turn this feature
on or off, follow the directions included later in this
section. See ªMemory and Personalization Featuresº
in the Index.
When the vehicle is shifted out of REVERSE (R) and a
five second delay has occurred, the passenger's mirror
will return to its original position. If further adjustment
is needed after the mirror is tilted, the mirror switch may
be used. The mirror then returns to its original position.

2-51 Convex Outside Mirror
Your passenger's side mirror is convex. A convex mirror's
surface is curved so you can see more from the driver's seat.
This mirror does not have a dimming feature.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
Heated Outside Mirrors
When you operate the rear window defogger, it also
warms both outside mirrors to help clear them of fog
or ice. See ªRear Window Defoggerº in the Index for
more information.
Storage Compartments
Glove Box
The glove box is located on the instrument panel in
front of the passenger's seat. To lock the glove box
door, insert the oval key into the lock cylinder and turn
it clockwise. Turn the key counterclockwise to unlock
the door.
Overhead Console
Sunglasses Storage Compartment
This feature is on vehicles without the optional sunroof.
To gain access to this compartment, which is located
directly above the inside rearview mirror in the headliner,
push up on the compartment and the storage area
will open.
Map Pocket
The map/storage pockets are located on each front door
as well as on the passenger's and driver's front seatbacks.