clock CADILLAC ESCALADE ESV 2007 2.G Owner's Manual

Turn the wheel wrench clockwise to raise the
vehicle. Raise the vehicle far enough off
the ground so there is enough room for the
spare tire to clear the ground.Rear Tire Flat:If the at tire is on a rear tire
of the vehicle, you will need to use the
jack handle (B) and both jack handle
extensions (C). Attach the wheel wrench (D) to
the jack handle extensions (C). Attach the
jack handle (B) to the jack (A). Use the jacking
pad provided on the rear axle. Turn the
wheel wrench (D) clockwise to raise the
vehicle. Raise the vehicle far enough off the
ground so there is enough room for the spare
tire to clear the ground.
Rear Position
485

{CAUTION:
Never use oil or grease on studs or nuts.
If you do, the nuts might come loose.
Your wheel could fall off, causing a
serious accident.
8. Put the wheel nuts back on with the rounded
end of the nuts toward the wheel after
mounting the spare tire.
9. Tighten each wheel nut by hand. Then use
the wheel wrench to tighten the nuts until the
wheel is held against the hub.
10. Turn the wheel wrench counterclockwise to
lower the vehicle. Lower the jack completely.
{CAUTION:
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the wheel
to come loose and even come off. This
could lead to an accident. Be sure to use
the correct wheel nuts. If you have to
replace them, be sure to get new GM
original equipment wheel nuts. Stop
somewhere as soon as you can and have
the nuts tightened with a torque wrench to
the proper torque specication. See
Capacities and Specifications on page 515
for wheel nut torque specication.
487

Notice:Improperly tightened wheel nuts can
lead to brake pulsation and rotor damage.
To avoid expensive brake repairs, evenly
tighten the wheel nuts in the proper sequence
and to the proper torque specication. See
Capacities and Specifications on page 515for
the wheel nut torque specication.
11. Tighten the nuts
rmly in a crisscross
sequence as
shown by turning
the wheel wrench
clockwise.
When you reinstall the regular wheel and tire, you
must also reinstall the bolt-on hub cap. Align
the plastic nut caps with the wheel nuts and then
tighten by hand. Then use the wheel wrench
to tighten.Secondary Latch System
Your vehicle has an underbody-mounted tire hoist
assembly which has a secondary latch system.
It is designed to stop the spare tire from suddenly
falling off your vehicle. For the secondary latch
to work, the spare tire must be installed with
the valve stem pointing down. SeeStoring a Flat
or Spare Tire and Tools on page 492.
{CAUTION:
Before beginning this procedure read all
the instructions. Failure to read and follow
the instructions could damage the hoist
assembly and you and others could get
hurt. Read and follow the instructions
listed next.
488

To release the spare tire from the secondary latch,
do the following:
1. Check under the
vehicle to see if the
cable end is
visible. If the cable
is not visible,
proceed to Step 6.
2. If it is visible, rst try to tighten the cable by
turning the wheel wrench clockwise until you
hear two clicks or feel it skip twice. You
cannot overtighten the cable.
3. Loosen the cable by turning the wheel wrench
counterclockwise three or four turns.
4. Repeat this procedure at least two times.
If the spare tire lowers to the ground,
continue with Step 5 ofRemoving the Spare
Tire and Tools on page 478.5. If the spare tire does not lower, turn the wheel
wrench counterclockwise until approximately
6 inches (15 cm) of cable is exposed.
6. Stand the wheel blocks on their shortest ends,
with the backs facing each other.
7. Place the bottom
edge of the jack (A)
on the wheel
blocks (B),
separating them so
that the jack is
balanced securely.
489

8. Attach the jack handle, extension, and wheel
wrench to the jack and place it (with the
wheel blocks) under the vehicle toward the
front of the rear bumper.9. Position the center lift point of the jack under
the center of the spare tire.
10. Turn the wheel wrench clockwise to raise the
jack until it lifts the end tting.
11. Continue raising the jack until the spare tire
stops moving upward and is held rmly in
place so that the secondary latch has released
and the spare tire is balancing on the jack.
12. Lower the jack by turning the wheel wrench
counterclockwise. Keep lowering the jack
until the spare tire slides off the jack or
is hanging by the cable.
490

{CAUTION:
Someone standing too close during the
procedure could be injured by the jack.
If the spare tire does not slide off the jack
completely, make sure no one is behind
you or on either side of you as you pull
the jack out from under the spare.
13. Disconnect the jack handle from the jack and
carefully remove the jack with the other hand.
14. Use one hand to push against the spare while
rmly pulling the jack out from under the
spare tire with the other hand. If the spare tire
is hanging from the cable, insert the hoist
end of the extension, and wheel wrench into
the hoist shaft hole in the bumper and
turn the wheel wrench counterclockwise to
lower the spare tire the rest of the way.15. Tilt the tire retainer
at the end of the
cable and pull
it through the wheel
opening. Pull the
tire out from
under the vehicle.
16. Turn the wheel wrench in the hoist shaft hole
in the bumper clockwise to raise the cable
back up if the cable is hanging under
the vehicle.
Have the hoist assembly inspected as soon as
you can. You will not be able to store a spare or
at tire using the hoist assembly until it has
been replaced.
To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 482.
491

6. Raise the tire fully against the underside of
the vehicle by turning the wheel wrench
clockwise until you hear two clicks or feel it
skip twice. You cannot overtighten the cable.
7. Make sure the tire is stored securely. Push,
pull (A), and then try to turn (B) the tire. If the
tire moves, use the wheel wrench to tighten
the cable.
8. Reinstall the spare tire lock.
9. Reinstall the hoist shaft access cover.
10. Reinstall the hitch cover.To store the tools, do the following.
A. Wheel Blocks
B. Tool Bag with
Jack Tools
C. Retaining Bracket
D. Wing Nut Retaining
Tool BagE. Jack
F. Wing Nut Retaining
Wheel Blocks
G. Wing Nut on Jack
1. Return the tools (wheel wrench, jack handle,
and jack handle extensions) to the tool bag (B).
2. Assemble wheel blocks (A) and jack (E)
together with the wing nut (F).
494

3. Position the jack (E) and wheel blocks (A) in
the driver’s side trim panel over the
wheelhouse.
4. Turn the wing nut (G) clockwise until the jack
is secured tight in the mounting bracket. Be
sure to position the holes in the base of
the jack onto the pin in the mounting bracket.
5. Use the retaining bracket (C) to fasten the tool
bag (B) on the stud and turn the wing nut (D)
clockwise to secure.
6. Return the storage tray to its original stored
position.Spare Tire
Your vehicle, when new, had a fully-inated spare
tire. A spare tire may lose air over time, so check its
ination pressure regularly. SeeInation - Tire
Pressure on page 460andLoading Your Vehicle on
page 370for information regarding proper tire
ination and loading your vehicle. For instruction on
how to remove, install, or store a spare tire, see
Removing the Flat Tire and Installing the Spare Tire
on page 482andStoring a Flat or Spare Tire and
Tools on page 492.
After installing the spare tire on your vehicle, you
should stop as soon as possible and make
sure the spare is correctly inated. Have the
damaged or at road tire repaired or replaced as
soon as you can and installed back onto your
vehicle. This way, a spare tire will be available in
case you need it again.
Your vehicle may have a different size spare tire
than the road tires, those originally installed on your
vehicle. This spare tire was developed for use on
your vehicle, so it is all right to drive on it.
Regular Wheelbase shown, Extended Wheelbase
similar.
495

A
Accessories and Modications..................... 396
Accessory Power Outlet(s).......................... 218
Adding Equipment to Your Airbag-Equipped
Vehicle..................................................... 107
Additives, Fuel............................................ 399
Add-On Electrical Equipment....................... 506
Adjustable Throttle and Brake Pedal............ 142
Air Cleaner/Filter, Engine............................. 412
Air Conditioning........................................... 220
Airbag
Passenger Status Indicator....................... 233
Readiness Light....................................... 232
Airbag Sensing and Diagnostic
Module (SDM).......................................... 551
Airbag System............................................... 90
Adding Equipment to Your
Airbag-Equipped Vehicle....................... 107
How Does an Airbag Restrain?.................. 99
Passenger Sensing System...................... 101
Servicing Your Airbag-Equipped Vehicle.... 106
What Makes an Airbag Inate?.................. 99
What Will You See After an Airbag
Inates?................................................ 100
When Should an Airbag Inate?................. 96
Where Are the Airbags?............................. 93Airbag System (cont.)
All-Wheel Drive........................................... 443
All-Wheel-Drive (AWD) System.................... 332
Analog Clock............................................... 219
Antenna, Rear Side Window........................ 319
Antenna, XM™ Satellite Radio Antenna
System.................................................... 320
Anti-Lock Brake System (ABS).................... 327
Anti-Lock Brake, System Warning Light....... 237
Appearance Care
Aluminum or Chrome-Plated Wheels........ 502
Care of Safety Belts................................ 499
Chemical Paint Spotting........................... 504
Cleaning Exterior Lamps/Lenses.............. 500
Cleaning the Inside of Your Vehicle.......... 496
Fabric/Carpet........................................... 497
Finish Care.............................................. 501
Finish Damage......................................... 504
Instrument Panel, Vinyl, and Other
Plastic Surfaces.................................... 499
Leather.................................................... 498
Sheet Metal Damage............................... 503
Speaker Covers....................................... 499
Tires........................................................ 503
Underbody Maintenance........................... 504
Vehicle Care/Appearance Materials.......... 505
Washing Your Vehicle .............................. 500
559

Cleaning (cont.)
Windshield, Backglass, and
Wiper Blades........................................ 502
Wood Panels........................................... 499
Climate Control System
Dual Automatic......................................... 220
Outlet Adjustment..................................... 225
Rear Air Conditioning and Heating
System, Electronic................................ 226
Clock.......................................................... 219
Collision Damage Repair............................. 552
Comfort Guides, Rear Safety Belt................. 56
Compass............................................157, 159
Content Theft-Deterrent............................... 135
Control of a Vehicle..................................... 326
Convenience Net......................................... 181
Coolant
Engine Temperature Gage........................ 238
Heater, Engine......................................... 143
Surge Tank Pressure Cap........................ 422
Cooled Seats................................................ 12
Cooling System........................................... 425
Cruise Control............................................. 202
Cruise Control Light.................................... 243
Cupholder(s)................................................ 178Customer Assistance Information
Courtesy Transportation........................... 549
Customer Assistance for Text
Telephone (TTY) Users ......................... 543
Customer Assistance Offices.................... 544
Customer Satisfaction Procedure.............. 540
GM Mobility Reimbursement Program...... 545
Reporting Safety Defects to
General Motors..................................... 557
Reporting Safety Defects to the
Canadian Government.......................... 556
Reporting Safety Defects to the
United States Government.................... 556
Roadside Service..................................... 545
Service Publications Ordering
Information........................................... 557
D
Daytime Running Lamps............................. 210
Defensive Driving........................................ 322
Delayed Locking.......................................... 124
Differential, Locking..................................... 329
Doing Your Own Service Work.................... 397
Dome Lamp Override.................................. 213
Dome Lamps............................................... 212
562