fuse CADILLAC STS V 2007 1.G Owners Manual

If a door, hood, or the trunk is opened without
the keyless access transmitter, the horn will
sound for 30 seconds and the lamps will ash
for two minutes. The vehicle cannot be started
without a keyless access transmitter.
The Theft-Deterrent system will not arm if:
The key is used to turn the key cylinder to
the lock position.
The driver’s door is locked using the power
door lock switch after the doors are closed.
If the vehicle is locked using the keyless access
transmitter and the trunk lid, hood or a door
is open or not closed completely, the security
light will ash for 60 seconds and then turn off.
At this time, the theft-deterrent system is armed
but the alarm will not sound if the trunk lid, hood or
door that was not closed completely is tampered
with or opened. The alarm will sound for the
trunk lid, hood or a door that was completely
closed at the time the vehicle was locked using
the keyless access transmitter.
The vehicle can be programmed to automatically
unlock the doors and disarm the theft-deterrent
system when you approach the vehicle and
the keyless access transmitter is with you. See
Vehicle Personalization on page 148.Pressing the unlock button on the keyless access
transmitter or using the key to unlock the
driver’s door disarms the theft-deterrent system.
Unlocking a door any other way while the
system is armed will activate the alarm.
Testing the Alarm
1. From inside the vehicle, roll down the window,
then get out of the vehicle, keeping the
door open.
2. From outside of the vehicle, with the door
open, lock the vehicle using the power door
lock switch or the keyless access transmitter
and close the door. Wait about 30 seconds
until the security light goes off.
3. Reach in and open the door using the inside
door handle. The horn will sound and the
exterior lamps will ash.
You can turn off the alarm by pressing the unlock
button on the keyless access transmitter or by
starting the car.
If the alarm does not sound when it should, check to
see if the horn works. The horn fuse may be blown.
109

To replace the fuse, seeFuses and Circuit
Breakers on page 487. If the fuse does not need to
be replaced, you may need to have your vehicle
serviced.
To reduce the possibility of theft, always arm the
Theft-Deterrent system when leaving your vehicle.
Valet Lockout Switch
The valet lockout switch
is located inside the
glove box.
9(Off):Press the left side of the valet lockout
switch to turn the lockout feature off. When the
lockout feature is off, you can open the trunk using
either the keyless access transmitter or the trunk
release button located on the driver’s door.
R(On):Press the right side of the valet lockout
switch to turn the lockout feature on. When
the lockout feature is turned on, the trunk cannot
be unlocked with the keyless access transmitter
or the trunk release button located on the driver’s
door. If the valet lockout feature is on it will
also disable the remote start feature and the
Universal Home Remote transmitter, if equipped.
Locking the glove box with your key will also
help to secure your vehicle.
SeeKeyless Access System Operation on
page 88andTrunk on page 101for additional
information.
110

Engine Coolant Heater
Your vehicle may be equipped with an engine
coolant heater.
In very cold weather, 0°F (−18°C) or colder, the
engine coolant heater can help. You will get easier
starting and better fuel economy during engine
warm-up.
Usually, the coolant heater should be plugged in a
minimum of four hours prior to starting your
vehicle. At temperatures above 32°F (0°C), use of
the coolant heater is not required. Your vehicle
may also have an internal thermostat in the
plug end of the cord. This will prevent operation of
the engine coolant heater when the temperature
is at or above 0°F (−18°C) as noted on the cord.
To Use the Engine Coolant Heater
1. Turn off the engine.
2. Open the hood and unwrap the electrical cord.
For the 3.6L V6 engine, the cord is located in
the engine compartment on the passenger’s
side of the vehicle in front of the fuse block.
For the 4.6L V8 engine, the cord is located in
the engine compartment on the driver’s
side of the vehicle near the inner fender and
above the strut.
For the 4.4L V8 engine, the cord is located in
the front of the engine compartment, on
the passenger’s side of the vehicle. The plug
will be inside the upper grille cutout.
3. You must remove the plastic cap to access
the plug.
115

Raise or lower the lever until the arrow starts to
ash to signal a lane change. Hold it there until the
lane change is complete. The lever returns to its
original position when it is released.
Rapid ashing of arrows when signaling for a turn
or lane change may be caused by a burned-out
signal bulb. Other driver’s will not see the signal.
Replace burned-out bulbs to help avoid possible
accidents. Check the fuse and for burned-out bulbs
if the arrow fails to work when signaling a turn.
SeeFuses and Circuit Breakers on page 487for
more information.
Turn Signal On Chime
If the turn signal is left on for about 1 mile (1.6 km),
a warning chime will sound and the TURN
SIGNAL ON message will appear on the Driver
Information Center (DIC) display. See “Turn Signal
On” underDIC Warnings and Messages on
page 264for more information.
Headlamp High/Low-Beam Changer
Push forward on the turn signal/multifunction
lever to change the headlamps from low to high
beam. Pull the lever back and then release it
to change from high to low beam.
If you turn the vehicle off with the high beams on,
the next time you start your vehicle the low
beams will be on.
To re-activate high beams, pull lever toward you
and then push it forward again.
This light on the
instrument panel cluster
will be on, indicating
high-beam usage.
183

To turn the HUD image off, turn the knob
counter-clockwise.
Polarized sunglasses could make the HUD image
harder to see.
As light shines out from the HUD, it is possible for
light to shine back in. In rare occurrences,
when the sun is at a specic angle and position,
the sun’s rays can shine back into the HUD. When
this occurs, the display device within the HUD
will be temporarily illuminated. The event will end
when the vehicle’s angle to the sun changes.
Clean the inside of the windshield as needed to
remove any dirt or lm that reduces the sharpness
or clarity of the HUD image.
To clean the HUD, spray household glass cleaner
on a soft, clean cloth. Wipe the HUD lens gently,
then dry it.
Notice:When cleaning, be careful not to
scratch the HUD or camera lenses. Do
not spray glass cleaner directly on the HUD
lens because the cleaner could leak inside the
unit and cause damage.
If the ignition is on and you cannot see the HUD
image, check to see if:
Something is covering the HUD unit.
The brightness is adjusted properly.
The HUD image is adjusted to the
proper height.
Ambient light in the direction your vehicle is
facing is low.
A fuse is blown. SeeFuses and Circuit
Breakers on page 487.
Keep in mind that your windshield is part of the
HUD system. SeeWindshield Replacement
on page 419.
The following Adaptive Cruise Control message
may appear in the HUD:
PEDAL APPLIED ACC OVERRIDE:This
message indicates that you are pressing your
foot on the accelerator pedal and overriding
Adaptive Cruise Control. While you are doing
this, the system will not automatically apply the
brakes. Once you remove your foot from the
accelerator pedal, Adaptive Cruise Control will
return to normal operation and be able to apply
the brakes, if needed.
You may also see an Adaptive Cruise Control
active symbol, alert symbol or vehicle ahead
symbol. SeeAdaptive Cruise Control on page 197
for more information.
225

Certain accessory power plugs may not be
compatible to the accessory power outlet and
could result in blown vehicle or adapter fuses. If
you experience a problem, see your dealer
for additional information on the accessory
power outlets.
Notice:Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should. The
repairs would not be covered by your
warranty. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
Check with your dealer before adding electrical
equipment.
Follow the proper installation instructions that are
included with any electrical equipment you install.
Notice:Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.Ashtray(s) and Cigarette Lighter
Your vehicle may have an ashtray and
cigarette lighter.
Notice:If you put papers, pins, or other
ammable items in the ashtray, hot cigarettes
or other smoking materials could ignite
them and possibly damage your vehicle. Never
put ammable items in the ashtray.
Ashtray
The ashtray is located under the climate control
panel on the center console. Press on the door to
release the ashtray. The ashtray will automatically
slide open for use.
To empty the ashtray with the ashtray in full open
position, locate the release button to the right
of the ash receiver and slide it to the right (in the
direction of the arrow). The ash receiver will
unlock and lift slightly and can then be easily
removed from the housing. To replace the
ash receiver, place it into position in the ashtray
housing and push down rmly until it locks
into place.
229

Cigarette Lighter
Notice:Holding a cigarette lighter in while it
is heating will not allow the lighter to back
away from the heating element when it is hot.
Damage from overheating may occur to the
lighter or heating element, or a fuse could be
blown. Do not hold a cigarette lighter in
while it is heating. Do not use equipment
exceeding maximum amperage rating of
15 amperes.
The cigarette lighter is located next to the ashtray.
The vehicle does not have any cigarette lighters
for the rear seat passengers.
To activate the cigarette lighter, push it into the
heating element and let go. When the lighter
is ready it will pop back out by itself.
Climate Controls
Dual Climate Control System
With this system you can control the heating,
cooling, and ventilation for the vehicle.
Automatic Operation
Vehicles With Heated and Ventilated Seats Shown,
Vehicles Without Similar
230

Vehicle Identication.................................. 485
Vehicle Identication Number (VIN)........... 485
Service Parts Identication Label............... 485
Electrical System........................................ 486
Add-On Electrical Equipment..................... 486
Headlamp Wiring....................................... 486
Windshield Wiper Fuses............................ 486Power Windows and Other Power
Options.................................................. 487
Fuses and Circuit Breakers....................... 487
Underhood Fuse Block.............................. 488
Rear Underseat Fuse Block....................... 492
Capacities and Specications.................... 498
Section 5 Service and Appearance Care
361

Doing Your Own Service Work
{CAUTION:
You can be injured and your vehicle could
be damaged if you try to do service work
on a vehicle without knowing enough
about it.
Be sure you have sufficient knowledge,
experience, the proper replacement
parts, and tools before you attempt any
vehicle maintenance task.
Be sure to use the proper nuts, bolts,
and other fasteners. English and metric
fasteners can be easily confused. If you
use the wrong fasteners, parts can later
break or fall off. You could be hurt.If you want to do some of your own service work,
you should use the proper service manual. It
tells you much more about how to service your
vehicle than this manual can. To order the proper
service manual, seeService Publications
Ordering Information on page 543.
Your vehicle has an airbag system. Before
attempting to do your own service work, see
Servicing Your Airbag-Equipped Vehicle on
page 78.
You should keep a record with all parts receipts
and list the mileage and the date of any service
work you perform. SeeMaintenance Record
on page 521.
364

After you have removed the sight shields (if equipped) on the 3.6L V6 engine, here is what you will see:
A. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 488.
B. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 404.
C. Battery. SeeBattery on page 408.
D. Passenger Compartment Air Filter. See
Passenger Compartment Air Filter on page 239.
E. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 403.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 380.G. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 380.
H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 405.
I. Engine Coolant Surge Tank and Pressure Cap.
SeeCoolant Surge Tank Pressure Cap on
page 393andCooling System on page 396.
J. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 386.
375