manual transmission CADILLAC XLR 2006 1.G Owners Manual

Driver Shift Control (DSC)
The Driver Shift Control (DSC) feature lets you manually
control over the operation of the transmission.
To use this feature,
move the shift lever
from the AUTOMATIC
OVERDRIVE (D) position
to the left and into the
driver shift control gate.
XLR
The DSC mode is selected by moving the shift lever
into the DSC area, which activates the driver manual
gear selection. To request an upshift in DSC, briey
move the shift lever up toward the plus (+) symbol.
To request a downshift, briey move the shift lever
down toward the minus (−) symbol. A plus (+)
symbol will appear on the shift console above the
AUTOMATIC OVERDRIVE (D) indicator and
minus symbol will appear below the indicator.The Head-Up Display (HUD) will also display the
change in gear, though the actual upshift or downshift
may be delayed until the engine speed is correct for that
gear. The gear displays on the HUD until the next
time you upshift or downshift. The gear selected and
shown in the HUD is one of a number of gears available.
It does not mean that the vehicle will operate only in
that specic gear. The actual gear that the vehicle shifts
to depends on a combination of the driver-requested
gear range, vehicle speed and throttle position.
XLR-V
The Sport Automatic Mode is selected by moving the
shift lever into the DSC area without shifting towards
the plus (+) or minus (−) symbols. While in the
Sport Automatic Mode, the transmission computer
determines when the vehicle is being driven in a
competitive manner. It will then select and hold the
transmission in lower gears and have more noticeable
upshifts for a sportier vehicle performance until you
use the plus (+) or minus (−) controls, which activates
the driver manual gear selection. A plus (+) symbol
will appear on the shift console above the AUTOMATIC
OVERDRIVE (D) indicator and minus symbol will
appear below the indicator. The Head-Up Display (HUD)
will also display the change in gear, though the actual
upshift or downshift may be delayed until the engine
speed is correct for that gear.
2-27

The gear displays on the HUD until the next time you
upshift or downshift.
The gear selected and shown in the HUD is one of a
number of gears available. It does not mean that
the vehicle will operate only in that specic gear.
Notice:If you drive your vehicle at high RPMs
without upshifting while using Driver Shift Control
(DSC), you could damage your vehicle. Always
upshift when necessary while using DSC.
If you do not upshift as the engine approaches the
red line on the engine rpm (revolutions per minute) gage,
the engine speed is controlled to limit the engine rpm.
Not all manual downshift requests will be allowed
by the transmission. To prevent excessive engine rpms,
each gear has a maximum vehicle speed associated
with it. Any downshift request above this speed will
not be allowed by the transmission.
If shifting is prevented for any reason, the current
gear will ash multiple times in the DIC, indicating
that the transmission has not shifted gears.
Some automatic downshifts may occur to maintain
minimum engine speed. This only happens if the vehicle
is left in too high of a gear for the vehicle’s speed.For example, if you have been driving in fth gear range
and come to a stop without manually downshifting,
fth gear will continue to display in the HUD. The
transmission will automatically downshift to second gear.
As you begin to drive and accelerate, the transmission
will automatically upshift as quickly as possible to the
selected fth gear.
In higher gears, an automatic downshift will occur if you
press the accelerator pedal to the oor. This feature
provides adequate acceleration capabilities if you forget
to downshift manually.
Automatic upshifts and downshifts will not display in
the HUD.
DSC can be used while using cruise control, but
transmission shifting will be different while the cruise
control is on. This is not a malfunction and is necessary
to allow proper operation of the cruise control.
To return to fully automatic operation, move the shift
lever to the right and back into the AUTOMATIC
OVERDRIVE (D).
When accelerating your vehicle from a stop in snowy
and icy conditions, you may want to shift into second
gear. A higher gear allows you to gain more traction on
slippery surfaces.
2-28

Follow these steps to reinstall the covers to the engine
air cleaner/lter housings:
1. Align the four tabs located on the back of the cover
with the three slots on the back of the housing.
2. Push the cover slightly down and towards the
engine to engage the tabs in the slots and align the
two wing screws.
3. Engage and tighten the two clasps on the top of the
engine air cleaner/lter cover.
{CAUTION:
Operating the engine with the air cleaner/lter
off can cause you or others to be burned.
The air cleaner not only cleans the air; it helps
to stop ames if the engine backres. If it is
not there and the engine backres, you could
be burned. Do not drive with it off, and be
careful working on the engine with the air
cleaner/lter off.
Notice:If the air cleaner/lter is off, a backre can
cause a damaging engine re. And, dirt can easily get
into your engine, which will damage it. Always have
the air cleaner/lter in place when you are driving.
Automatic Transmission Fluid
How to Check Automatic
Transmission Fluid
It is not necessary to check the transmission uid level.
A transmission uid leak is the only reason for uid
loss. If a leak occurs, take the vehicle to the dealership
service department and have it repaired as soon as
possible.
There is a special procedure for checking and changing
the transmission uid. Because this procedure is
difficult, you should have this done at the dealership
service department. Contact your dealer for additional
information or the procedure can be found in the service
manual. To purchase a service manual, seeService
Publications Ordering Information on page 8-14.
Notice:Use of the incorrect automatic transmission
uid may damage your vehicle, and the damages
may not be covered by your warranty. Always
use the automatic transmission uid listed in
Recommended Fluids and Lubricants on page 7-11.
Change the uid and lter at the intervals listed in
Additional Required Services on page 7-6, and be sure
to use the uid listed inRecommended Fluids and
Lubricants on page 7-11.
6-21

Notice:If you try to start your vehicle by pushing
or pulling it, you could damage your vehicle. Do not
push or pull your vehicle to start it; instead, use
the jump starting procedure in this manual to start
your vehicle when the battery has run down.
1. Check the other vehicle. It must have a 12-volt
battery with a negative ground system.
Notice:If the other vehicle’s system is not a 12-volt
system with a negative ground, both vehicles can
be damaged. Only use vehicles with 12-volt systems
with negative grounds to jump start your vehicle.
2. Get the vehicles close enough so the jumper cables
can reach, but be sure the vehicles are not touching
each other. If they are, it could cause a ground
connection you do not want. You would not be able
to start your vehicle, and the bad grounding
could damage the electrical systems.
To avoid the possibility of the vehicles rolling, set
the parking brake rmly on both vehicles involved
in the jump start procedure. Put an automatic
transmission in PARK (P) or a manual transmission
in NEUTRAL before setting the parking brake.Notice:If you leave your radio or other accessories
on during the jump starting procedure, they could
be damaged. The repairs would not be covered
by your warranty. Always turn off your radio and
other accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or the accessory power outlet. Turn off
the radio and all lamps that are not needed.
This will avoid sparks and help save both batteries.
And it could save the radio!
4. Open the hoods and locate the batteries. Find the
positive (+) and negative (−) terminal locations on
each vehicle. SeeEngine Compartment Overview
on page 6-12for more information on location.
{CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.
6-40

Capacities and Specications
The following approximate capacities are given in English and metric conversions. Please refer toRecommended
Fluids and Lubricants on page 7-11for more information.
ApplicationCapacities
English Metric
Automatic Transmission (Pan Removal and Replacement)
5-Speed Automatic 9.5 qt 9.0 L
6-Speed Automatic 6.5 qt 6.2 L
Cooling System 12.6 qt 12.0 L
Engine Oil with Filter – 4.4L V8 and 4.6L V8 Engines 8.0 qt 7.6 L
Fuel Tank 18.0 gal 68.0 L
Intercooler System 2.4 qt 2.3 L
Wheel Nut Torque 100 ft lb 140Y
All capacities are approximate. When adding, be sure to ll to the approximate level as recommended in this manual.
Recheck uid level after lling.
Engine Specications
Engine VIN Code Transmission Spark Plug Gap
4.4L V8 D Automatic 0.040 inches (1.02 mm)
4.6L V8 A Automatic 0.040 inches (1.02 mm)
6-92

Reporting Safety Defects to the
Canadian Government
If you live in Canada, and you believe that your vehicle
has a safety defect, you should immediately notify
Transport Canada, in addition to notifying General
Motors of Canada Limited. You may call them at
1-800-333-0510 or write to:
Transport Canada
Place de Ville Tower C
330 Sparks Street
Ottawa, Ontario K1A 0N5
Reporting Safety Defects to
General Motors
In addition to notifying NHTSA (or Transport Canada)
in a situation like this, we certainly hope you will
notify us. Please call us at 1-800-458-8006, or write:
Cadillac Customer Assistance Center
Cadillac Motor Car Division
P.O. Box 33169
Detroit, MI 48232-5169In Canada, please call us at 1-888-446-2000. Or, write:
Canadian Cadillac Customer Communication
Centre, 163-005
General Motors of Canada Limited
1908 Colonel Sam Drive
Oshawa, Ontario L1H 8P7
Service Publications Ordering
Information
Service Manuals
Service Manuals have the diagnosis and repair
information on engines, transmission, axle suspension,
brakes, electrical, steering, body, etc.
Transmission, Transaxle, Transfer
Case Unit Repair Manual
This manual provides information on unit repair service
procedures, adjustments, and specications for
GM transmissions, transaxles, and transfer cases.
8-14