engine CHEVROLET C/K 2003 User Guide

2-23 Exhaust Restrictor (Diesel Engines)
(If Equipped)
If your vehicle is equipped with this feature, there is an
exhaust restrictor valve located in the exhaust stream.
The valve closes to provide back pressure to the engine
for the purpose of warming the engine quickly.
The exhaust restrictor operates:

while the engine is running.

while the vehicle is not moving.

while the accelerator, brake and clutch pedals are
not pressed.

while idling or driving in cold temperatures.

when the shift lever is in NEUTRAL (N)
or PARK (P).On vehicles equipped with a diesel engine exhaust
brake, the exhaust brake switch must be on. The
indicator in the exhaust brake switch will be lit when the
exhaust restrictor is active. The exhaust brake indicator
light in the center of the instrument panel will also be lit
whenever the exhaust restrictor is active.
When the engine coolant temperature is below 149F
(65C) and the outside temperature is below 50F
(10C), the exhaust restrictor will come on within
45 seconds of starting the engine. After running the
engine for an additional 45 seconds, the engine idle
will increase.
The exhaust restrictor will shut off and engine idle will
return to normal once the engine is warmed up, or the
transmission is shifted into range.

2-24
Starting Your DURAMAX

Diesel Engine
Your diesel engine starts differently than a
gasoline engine.
Automatic Transmission
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's
a safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transmission. Shift to PARK (P) only when your
vehicle is stopped.
Manual Transmission
Move your shift lever to neutral and hold the clutch
pedal to the floor while starting the engine. Your vehicle
won't start if the clutch pedal is not all the way
down
-- that's a safety feature.
Starting Your Engine
1. Turn your ignition key to RUN.
Observe the wait to start light. See ªWait To Start
Lightº in the Index. (This light may not come on
if the engine is hot.)
2. As soon as the wait to start light goes off,
IMMEDIATELY turn the ignition key to START.
When the engine starts, let go of the key.
NOTICE:
Holding your key in START for longer than
15 seconds at a time will cause your battery to be
drained much sooner. And the excessive heat can
damage your starter motor.

2-25
NOTICE:
If the wait to start light stays on, it means that
your vehicle could have one of several problems,
so you should have it serviced right away.
3. If the engine does not start after 15 seconds of
cranking, turn the ignition key to OFF. Wait
one minute for the starter to cool, then try the
same steps again.
If you're trying to start your engine after you've run
out of fuel, follow the steps in ªRunning Out of Fuel.º
See ªDiesel Fuel Requirements and Fuel Systemº in
the Index.
When your engine is cold, let it run for a few minutes
before you move your vehicle. This lets oil pressure
build up. Your engine will sound louder when it's cold.
NOTICE:
If you're not in an idling vehicle and the engine
overheats, you wouldn't be there to see the
overheated engine condition. This could damage
your vehicle. Don't let your engine run when
you're not in your vehicle.
Cold Weather Starting (Diesel Engine)
The following tips will help you get good starting in
cold weather.
Use the recommended engine oil when the outside
temperature drops below freezing. See ªEngine Oilº in
the Index. When the outside temperature drops below
0
F (
-18
C), use of the engine coolant heater is
recommended.
If you experience longer cranking times, notice an
unusual amount of exhaust smoke or are at higher
altitudes (over 7,000 ft. or 2 135 m), you may use your
engine coolant heater. See ªEngine Coolant Heaterº in
the Index.
See ªDiesel Fuel Requirements and Fuel Systemº in the
Index for information on what fuel to use in cold weather.

2-26 If Your Diesel Engine Won't Start
If you've run out of fuel, look at ªRunning Out of Fuel.º
See ªDiesel Fuel Requirements and Fuel Systemº in
the Index.
If you're not out of fuel, and your engine won't start,
do this:
Turn your ignition key to RUN. IMMEDIATELY
after the wait to start light goes off, turn the ignition
key to START.
If the light doesn't go off, wait a few seconds, then try
starting your engine again. And, see your dealer as soon
as you can for a starting system check.
If the light comes on and then goes off and you know
your batteries are charged, but your engine still won't
start, your vehicle needs service.
If the light does not come on when the engine is cold,
your vehicle needs service.If your batteries don't have enough charge to start your
engine, see ªBatteryº in the owner's manual.
Be sure you have the right oil for your engine, and that
you've changed the oil at the proper times. If you use
the wrong oil, your engine may be harder to start.
Be sure you are using the proper fuel for existing
weather conditions. See ªDiesel Fuel Requirements and
Fuel Systemº in the Index.
If the engine starts, runs a short time, then stops, your
vehicle needs service.
CAUTION:
Do not use gasoline or starting ªaids,º such as
ether, in the air intake. They could damage your
engine. There could also be a fire, which could
cause serious personal injury.

2-27
Engine Checks Before Operating
When you've started your engine, let it run for 20 to
30 seconds before you put a load on the engine. But
don't leave the vehicle while the engine is running.
Avoid unnecessary idling of diesel engine equipped
vehicles.
If the engine idles too long, the temperature of the
engine coolant will fall below the normal operating
range. Low engine operating temperature causes several
conditions which affect engine operation and reduce
engine life.
The engine should be permitted to go through a
warm
-up period. Operate the vehicle at a minimum of
600 rpm during the warm
-up period. During this period
and during operation, the following observations should
be made.
During this warm
-up period, check your warning lights
and gages:

If oil pressure doesn't begin to rise within
15 seconds of starting, stop the engine and
find the cause.
If the engine coolant temperature gage needle goes
into the hot area on the gage, stop the engine and
find the cause of the overheating.

If you have air brakes, the dual
-needle air pressure
gage should read at least 115 psi (790 kPa) for both
service systems before you try to move the vehicle.
When air pressure is below 60 psi (420 kPa), the
LOW AIR light will come on and you will hear a
tone alarm. If the pressure doesn't build up or
drops during warm
-up, stop the engine and find
the cause before you try to move the vehicle.
Recommended air pressure before actually driving
away is 120 psi (830 kPa).

The charging system light should come on when
the ignition key is turned to RUN or START and
should go out when the engine is running above idle.
If the light doesn't go out or comes back on during
normal engine operation, have the charging system
checked right away. (This light tells you if the
generator is not charging; it doesn't reflect the
condition of the battery.)

2-28

The voltmeter charge indicator gage tells you the
condition of your battery's charge. The gage should
be in the center area during engine operation. The
red area on the left indicates an undercharge
condition; the red area on the right indicates an
overcharge. If the gage is in either red area, have the
battery and charging system checked right away.
NOTICE:
For diesel engines, don't allow the engine to
operate at low idle for more than five minutes.
This can cause low engine operating
temperatures which can affect engine operation
and reduce engine life. Engine idle speed should
be increased to 1200 rpm whenever extended idle
is required. Once started, the engine should be
placed under load to allow the engine coolant
temperature to reach 150F (66C) before
shutting off the engine.
Engine Coolant Heater (If Equipped)
If your vehicle is equipped
with this feature, the plug
-in
receptacle is located under
the driver's door.
In very cold weather, 0F (
-18C) or colder, the engine
coolant heater can help. You'll get easier starting and
better fuel economy during engine warm
-up. Usually,
the coolant heater should be plugged in a minimum of
four hours prior to starting your vehicle.

2-29 To Use the Engine Coolant Heater
1. Turn off the engine.
2. Find the plug
-in receptacle (either behind the front
bumper or in the component box).
3. Plug a heavy
-duty, three-prong extension cord
(rated for at least 15 amps) into the vehicle's plug
-in
receptacle first. Then plug the extension cord into a
normal, grounded 110
-volt AC outlet.
CAUTION:
Plugging the cord into an ungrounded outlet
could cause an electrical shock. Also, the wrong
kind of extension cord could overheat and cause
a fire. You could be seriously injured. Plug the
cord into a properly grounded three
-prong
11 0
-volt AC outlet. Use a heavy-duty three-prong
extension cord rated for at least 15 amps.
4. Before starting the engine, be sure to unplug
the cord.
How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature.
From 32
F to
-10
F (0
C to -23
C), keep the coolant
heater plugged in at least two hours. Below
-10
F
(
-23
C), keep the coolant heater plugged in for a
minimum of eight hours or overnight. It will not harm
either the coolant heater or the vehicle to leave the
coolant heater plugged in longer than the times stated.
Be sure to remove and store the cord before starting the
engine. See ªDiesel Fuel Requirements and Fuel
Systemº in the Index for information on what fuel to
use in cold weather.

2-30
Diesel Engine Exhaust Brake
(If Equipped)
The exhaust brake is available on vehicles equipped
with a diesel engine. It is located in the exhaust system.
The exhaust brake is used to help slow the vehicle and
may assist the vehicle's foundation brakes. The use of
the exhaust brake will assist the braking of the vehicle
and prolong the life of the foundation brake lining
material.
The exhaust brake switch is
located in the instrument
panel switchbank.Push the bottom of the switch to turn the exhaust brake
on. When you push the top of the switch, the exhaust
brake will turn off.
There is an indicator light on the instrument panel
similar to the symbol on the switch, that will come on
when the exhaust brake is active. See ªExhaust Brake
Indicator Lightº in the Index for more information.
When using the exhaust brake, the proper gear range
selection is important. The exhaust brake will be most
effective if the gear range selected is the lowest possible
range that does not allow the engine rpm to go more
than 200 rpm above rated (full load) rpm. If you have a
Caterpillar diesel engine, do not exceed 2900 rpm. If
you have a DURAMAX (LG4) diesel engine, do not
exceed 3200 rpm. If you have a DURAMAX (LB7)
diesel engine, do not exceed 3600 rpm.
If you have an automatic transmission and press this
button, the transmission will downshift to a factory
default setting of fourth gear. To change the default
setting, or for more information on factory default
settings, contact your dealer for assistance.

2-32
The two-speed axle should be in low when you park the
vehicle. You'll need to engage the transmission, even
move the vehicle a little, to be sure the axle is in the low
range. Then apply the parking brake, shift into
NEUTRAL and shut off the engine.
Also, always start the vehicle in motion with the
two
-speed axle in the low range. To shift up from low to
high, do the following:
1. Move the switch up for the high range,
2. disengage the clutch, and
3. after a brief pause, engage the clutch and then press
down on the accelerator.
To shift down from high to low, do the following:
1. Move the switch down to low,
2. release the accelerator and then quickly apply
it again.
Automatic Transmission
The rear axle shift control
switch for an automatic
transmission is located in
the instrument panel
switchbank.
Press the bottom of the switch to get to the low range.
The switch indicator light will come on when the
vehicle is in low range. Press the top of the switch to
return to the high range.
The two
-speed axle should be in low range when you
park the vehicle. Apply the parking brake, shift to
PARK (P) or NEUTRAL (N) and shut off the engine.
To operate off
-road or under a heavy load, shift into low
range when the vehicle is standing still and then operate
the transmission normally.

2-33
On the highway, with the axle in low range and the
transmission in top gear, you may shift the axle to high
range by raising the switch and releasing the accelerator
momentarily. Reapply the accelerator after you shift.
Under light load conditions, first shift the axle into the
high range with the vehicle at a standstill and then
operate the transmission normally.
Air Shift Control (Automatic Transmission)
The switch for the rear axle
shift control is located in the
instrument panel
switchbank.
Press the bottom of the switch to get to the low range.
Press the top of the switch to return to the high range.The two
-speed axle should be in low when you park
the vehicle.
You'll need to engage the transmission, even moving the
vehicle a little, to be sure the axle is in low range. Then
shift into PARK (P), apply the parking brake and shut
off the engine.
Also, always start the vehicle in motion with the
two
-speed axle in the low position. To shift up from
low to high, press the top of the rear axle shift control
switch and press down on the accelerator. When you
shift the axle from high to low, press the bottom of the
switch, release the accelerator and then quickly press it
down again.
Air Suspension (If Equipped)
Your vehicle may be equipped with the Hendrickson
HAS Series single
-axle air suspension which is designed
for single
-axle on-highway use. The feature is available
in 19,000 lb. (8 618.3 kg), 21,000 lb. (9 525.4 kg) and
23,000 lb. (10 432.6 kg) capacities for operations which
require extra cubic capacity and a reduced deck height.