electrical CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

ACCESSORIES 15-4

Fig. 5 - Servo Mounting

and the air bled into the chamber again equals the air

bled out. A balance occurs again with the diaphragm in

a new position. If the Regulator begins to supply more

bleed air, (vehicle speed increasing) the vacuum in the

chamber drops and the diaphragm moves away from the

vacuum port, withdrawing the tapered needle from the

orifice and enlarging it. Since the vacuum orifice is

now larger, the greater quantity of air being bled into

the chamber may be bled out by vacuum and a balance

again occurs with the diaphragm in a new position.

AIR

TO SERVO

VACUUM

TO SERVO
VACUUM

RELEASE

SWITCH

ELEaRIC

RELEASE

SWITCH

Fig.
6- Servo, Regulator and Hose
Fig. 7 - Release Switches and Brackets

REGULATOR

The Regulator is a device which has two primary

functions: First, it is a vacuum switch which, when en-

gaged by the driver, supplies engine manifold vacuum to

the Servo. Second, it meters a small variable quantity

of air to the Servo unit in order to change the carburetor

throttle opening to effect speed control. A secondary

function of the Regulator is to drive the speedometer.

Since the car speed is sensed by a speedometer-like

mechanism within the unit, the speedometer cable from

the transmission drives the Regulator which drives a

second cable (at a one to one ratio) to the speedometer.

The Regulator is electrically engaged and disengaged

through operation of the Engagement Switch and the

Electric Brake Release Switch. It has two sub-assem-

blies which make up the unit: one being the magnetic

speed sensing assembly and the other being the solenoid

actuated vacuum switch, air bleed and filter, and low

limit speed switch assembly (fig. 8 and 9).

Magnetic Speed Sensing Assembly

The speed sensing assembly operates in the same man-

ner as a speedometer unit except that instead of rotating

a needle through an angle proportional to the vehicle

speed, it rotates a rubber drum which is clutched to the

air bleed valve when the system is in operation. The

assembly is driven by the speedometer cable from the

transmission which turns a disk shaped ferrite magnet.

Facing the magnetic disk is the driven brass disk mounted

on a shaft with the rubber drum mounted on the same

shaft. A spiral hairspring connects the shaft to the

housing and allows it to rotate through an angle which is

proportional to car speed. If the car doubled its speed,

the shaft would rotate to twice its previous angle as may

be seen by noting the operation of a speedometer. The

CHEVROLET CHASSIS SERVICE MANUAL

driven disk is sandwiched between the magnetic disk and

a field plate. The field plate forms a returning path for

the magnetic field from the magnetic disk.

The gear drive for the magnetic disk is a 90 degree

nylon gear drive with the driven gear rotating both the

magnetic disK and the speedometer drive cable.

Vacuum Switch, Air Bleed and Filter, and Low

Limit Speed Switch

The end of the shaft from the speed sensing assembly

with the rubber drum extends into the air bleed metering

assembly. This rubber drum has a tang extending from

its surface which allows a set of points to close at a

specific car speed. When the car reaches about 20 mph,

the rubber drum has rotated far enough (moved by the

brass driven disk in the magnetic field) so that its tang

has allowed a spring loaded electrical point to contact

another point. These points are in series with the sole-

noid coil so that under 20 mph, no Regulator operation

is possible.

Surrounding the rubber drum is a "U" shaped spring

clip which is held spread away from the drum by the

nose or cam of the solenoid when the solenoid is in the

relaxed position. The rubber drum and this clip com-

prise the speed clutch of the regulator. When the sole-

noid is energized, the solenoid nose moves toward the

drum and releases the ends of the clip. The clip springs

inward and attaches itself by friction to the drum. Now,
ACCESSORIES 15-5

any change in car speed will rotate the drum and move

the "U" clip just as a speedometer moves its needle.

The top of the MUtf clip is attached to the air bleed valve.

The clip moves a sleeve which slides on the orifice

tube thereby covering and uncovering air ports in the

wall of the tube (the tube inner end is plugged) whenever

car speed changes from the speed at which the solenoid

was energized. The direction of drum rotation is such

that resulting bleed valve operation will cause the Servo

to decrease engine power if the car exceeds the preset

speed and increase engine power if car speed decreases.

The air which passes out the orifice tube enters the

Regulator through the openings in the solenoid housing,

passes through the oil wetted polyurethane filter, and then

enters the orifice tube ports.

When the solenoid is de-energized, the nose retracts

and cams the ends of the "U" clip outward so that it re-

leases the rubber drum.

The solenoid also operates a vacuum switch simul-

taneously with the clutching and declutching of the "U"

clip.
The vacuum switch supplies the Servo unit with

manifold vacuum. The solenoid operated vacuum valve

slides over two ports in the Regulator wall. One port

is connected to manifold vacuum and the other is con-

nected to the center port of the Servo unit. When the

solenoid is de-energized, the valve closes the manifold

vacuum port and opens the Servo port to the inside of

the regulator case. When the solenoid is energized, the

valve connects the Servo port to the manifold vacuum

AAAGNET

SPEED CUP

FIELD PLATE

HAIRSPRING
TO SPEEDOMETER

MAGNET HOUSING

ASSEMBLY
ORIFICE TUBE &

CONNECTOR ASSEM.
CONTROL

VALVE

CLUTCH

SPRING

LOW LIMIT

SPEED SWITCH

RUBBER

DRUM

VACUUM PORT

TO SERVO

INPUT CONNECTION

SOLENOID COIL

SOLENOID AND CLUTCH

HOUSING ASSEMBLY
VACUUM PORT

TO ENGINE

VACUUM VALVE

UNLOCKING CAM

•SOLENOID PLUNGER

AIR FILTER

SIDE VIEW SECTION

REGULATOR DISENGAGED
END VIEW SECTION

ENGAGED

Fig.
8 - Regulator-Cross Section '

CHEVROLET CHASSIS SERVICE MANUAL

ACCESSORIES 15-9

Adjustment- Adjust the bead chain so that it is as tight

as possible without holding the throttle open when the

carburetor is set at its lowest idle throttle position.

When connecting the bead chain (engine stopped) manually

set the fast idle cam at its lowest step and connect the

chain so that it does not hold the idle screw off the cam.

If the chain needs to be cut, cut it three beads beyond the

bead which pulls the linkage.

REGULATOR

Service - A defective regulator, that is one which is not

simply out of adjustment, must be replaced. During re-

placement, check the hoses which connect to the regulator

and replace any which are cracked or deteriorated.

Air Filter

The air filter located in the solenoid cover should be

cleaned and re-oiled at engine oil change intervals.

1.
Snap the solenoid cover off.

2.
Remove the filter and wash it in kerosene or mineral

spirits. Squeeze it dry and wet with SAE 10 engine

oil.
Squeeze out excess oil and reinstall into the

cover.

3.
Attach the cover with neoprene seal to the solenoid

housing. Be certain that the cover fits tightly to the

housing.

One regulator adjustment is possible: Engagement-

Cruising Speed Zeroing (to remove any difference be-

tween engagement and cruising speed).

NOTE:
No regulator adjustment should be

made, however, until the following items have

been checked or serviced:

1.
Bead chain properly adjusted.

2.
All hoses in good condition, properly attached, not

leaking, not pinched or kinked.

3.
Regulator air filter clean and properly oiled.

4.
Electric and vacuum release switches properly

adjusted.

Engagement—Cruising Speed Zeroing

If the cruising speed is lower than the engagement

speed, loosen the orifice tube locknut and turn the tube

outward; if higher, turn the tube inward. Each 1/8 turn

will alter the engagement-cruising speed difference one

mph. Tighten the locknut after adjustment and check the

system operation at 50 mph.

ELECTRICAL SYSTEM CHECK OUT

1.
Check fuse and connector.

2.
Check electric brake switch as follows: Unplug con-

nector at brake switch. Connect ohmmeter at points

A and B on brake switch. The ohmmeter must indi-

cate infinity when the brake pedal is depressed and

continuity when pedal is released. The cruise re-

lease brake switch (electric) is adjusted as is the

standard stop light brake switch. Replace electric

brake switch if needed.

3.
Check engagement switch and connecting wiring as
follows: Unplug push button control connector

(brown, blue, black) at electrical wiring harness con-

nector and perform the following tests. (See Fig-

ure 10)

Test #1
—
Connect ohmmeter between terminal #1 (brown

wire) and terminal #2 (blue wire). Continuity shall be

maintained until switch is depressed all the way in.

Test #2
—
Connect ohmmeter between terminal #1 (brown

wire) and terminal #3 (black). No continuity shall be

shown; however, when the button is depressed halfway,

continuity shall be indicated. When the button is pressed

all the way down, no continuity shall be shown.

Test #3 — Connect ohmmeter between terminal #2 (blue

wire) and terminal #3 (black). Button released, no con-

tinuity; however, when the button is depressed partially

and fully, continuity shall be shown.

4.
Check regulator solenoid coil, low-speed switch, and

wiring harness as follows:

a. Disconnect engagement switch wire harness con-

nector from the main wire harness connector

(brown, blue, and black wires). Connect ohm-

meter
'
between point C (blue wire in main wire

harness) and ground. (Make sure the regulator is

well grounded to chassis.) The ohmmeter should

read 45 ohms ± 2 ohms. If a resistance of

greater value is shown, then disconnect the con-

nector from the regulator and measure the re-

sistance of the blue wire from point C to D. It

should measure 40 ohms. Check the resistance

from point E (vertical bar of terminal forming T)

to ground. It should measure 5 ohms ± 1/4 ohm.

Replace either the wiring harness or solenoid as

needed if greater values are indicated. The black

harness wiring from point F to G should also be

checked for continuity.

ENGAGEMENT SWITCH TEST

BUTTON POSITION

Cruise (released)

Engage (partially depressed)

Trim (fully depressed)
TERMINALS

1 TO 2

closed

Closed

open
1 TO 3

open

closed

open
2 TO 3

open

closed

closed

SERVO AND VACUUM SYSTEM CHECK OUT

To determine the condition of the diaphragm, remove

hoses from power unit and apply 14 inches of vacuum to

either vacuum tube opening (seal the other opening) and

hold in for one minute. The vacuum shall not leak down

more than 5 inches of vacuum in one minute. If leakage

is detected, replace servo. To utilize engine as a vac-

uum source, proceed as follows:

1.
DISCONNECT SERVO $EAD CHAIN and hoses from

servo and connect engine vacuum directly to vacuum

servo fitting (fitting in middle of servo). Seal the

servo unit opening.

2.
Note position of servo diaphragm.

3.
Start engine - the diaphragm should pull in.

4.
Clamp off engine vacuum supply line and check for

leakage. '

The cruise release brake switch (vacuum) and connecting

hoses can likewise be checked using a vacuum pump.

CHEVROLET CHASSIS SERVICE MANUAL

CRUISE MASTER SYSTEM CHECKS

Will not engage

Does not cruise at engage-

ment speed

System hunts or pulses

System does not disengage -

with brake pedal

System applies full throtUe

when engaged

Cannot adjust speed down-

ward with Engage Button

Does not engage or engages

lower than limits referred

to in "Driver Operation"
Cause

Brake Switch Circuit Open

Fuse blown

Defective Engage Switch

Vacuum leak in Servo and/or Brake

Switch and connecting lines.

Open in wiring harness

Defective Regulator

Orifice Tube misadjusted

Bead Chain loose.

Kinked or deteriorated hoses

Dirty Air Filter

Defective and/or improperly posi-

tioned Drive Cables and/or Casing

Assemblies

Defective Regulator

Brake and/or Vacuum Switch mis-

adjusted or defective

Hoses interchanged at Servo

Defective Regulator

Defective Engagement Switch or

Wiring

Internally Misadjusted Regulator
Correction

Check connections - adjust or replace switch. Refer to

Electrical Check Out.

Replace fuse - if it blows again, check for:

1.
Engage Switch stuck in the center of travel - Refer

to Electrical Check Out.

2.
Incorrect wiring - Refer to Electrical Check Out.

3.
Short to ground - Refer to Electrical Check Out.

Make necessary corrections.

Replace as needed - Refer to Electrical Check Out.

Vacuum test and repair or replace as needed. Refer to

Servo and Vacuum System Check Out.

Repair or replace as needed.

Replace Regulator.

Adjust as required.

Tighten Bead Chain.

Repair or replace.

Service as required.

Repair or replace as needed.

Replace Regulator.

Adjust or replace as required. Refer to Servo

and Vacuum System Check Out and Electrical Check

Out.

Correct as needed.

Replace Regulator.

Replace as needed. Refer to Electrical Check Out.

Replace Regulator

ACCESSORIES 15-11

12 VOLTS D.C.
ELECTRIC BRAKE

RELEASE

IGNITION

SWITCH

ENGINE

VACUUM

TRANSDUCER

Fig.
11 - Vacuum and Electrical Diagram

AUTOMATIC LEVEL CONTROL

INDEX

Page

General Description . . 15-11

System Checks and Adjustments 15-13

Service Operation . 15-15

GENERAL DESCRIPTION

A pneumatic level control system that automatically

maintains correct rear trim height of a car under varying

load conditions, the optional automatic level control is

used only in conjunction with the Superlift Shock Absorber

option.

The Superlift Shock Absorber option alone, consists of

the two shock absorbers with pressure lines to a "Tee"

where a ill valve is located, the shocks are inflated

with (or deflated of) compressed air (at any gas station)

to obtain the vehicle level desired with any given load

change.

The automatic leveling system is added to the Superlift

Shock Absorbers and supplies its own compressed air.

The system (fig. 13) consists of a vacuum operated air

compressor with pressure regulator,
and
integral storage

tank, vacuum line to engine, air intake filter, air lines,

and a height control valve.

The COMPRESSOR is a two-stage, vacuum actuated

type, requiring no lubrication. Vacuum supply is taken

from engine carburetor base. High pressure air is
supplied to the reservoir tank by the second stage of

the two-stage compressor. The first stage intake stroke

draws air at atmospheric pressure through a oneway

check valve located in the end of the first stage housing

under the first ^tagei housing cover. On the first stage

compression stroke, the intake valve is closed and the

oneway check valve in the second stage end of the piston

is opened. This allows the air from the first stage

cylinder to flow through the hollow piston into the second

stage cylinder for jhigh pressure compression. The

second stage compression stroke closes the check valve

in the piston and opeijis the check valve in the end of the

second stage housing.

The intake and compression strokes are controlled by a

sliding distributor valive that is actuated through an arm

that is tripped by the piston as it nears the end of each

stroke. Each time the arm actuates the distributor

valve, a different set of holes are covered in the first

stage housing. The distributor valve controls the flow of

intake manifold vacuum and air under atmospheric pres-

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS
13

ENGINE ELECTRICAL

SECTION
6Y

BATTERY

Battery Model

Application

Ground

Plates

Cranking Power @ 0°F. (Watts)
1980032*

153L-4,
194, 230,

250L-6 & 283

V-8

Neg.

54

2300
1980030*

327,
350, 396

& 427 V-8

Neg.

66

2900
1980036*

396 & 427 V-8

w/AC & M-40

Trans.

Neg.

66

3150

*65° Side Recess and One Piece Cover Construction

GENERATOR

Generator Model

Application

Field Amp.

Draw

Hot
Output
—

Amps.

Cold Output -

Volts
1100695

Chevy n

Exc.
V-8,

Sta. Wgn.

or AC

2.2-2.6

32

14
1100693

Chevy n

w/V-8,

Camaro,

CheveUe,

Chevrolet

* and

Corvette

w/AC

2.2-2.6

37

14
1100696

Chevy II

w/AC &

RPO

K-66

2.2-2.6

42

14
1100742

Chevrolet

w/AC &

Turbo-

Hydramatic

2.8-3.2

63

14
110075Q

AUA/C

except*

w/RPO

M-40

and

Chevy H

2.2-2.6

61

14
1117754

Optional

3.7-4.4

62

14
1117777

Optional

4.14-4.62

62

14

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS 25

BODY AND CHASSIS ELECTRICAL

SECTION
12

LAMP USAGE
CANDLE

POWER
BULB

NUMBER

Headlamp Unit

Chevrolet, Chevelle & Corvette

Outer - High Beam

Outer - Low Beam

Inner -• High Beam only

Chevy H

High Beam . .

Low Beam

Parking Lamp and Directional Signal

All Exc. Camaro

Camaro

Tail, Stop and Directional Signal (Exc. Bel Air)

Backing Lamp ••...,

Instrument Illumination Lamps

Chevrolet & Camaro ,

Chevelle and Chevy n

Corvette

Temperature Indicator

Chevrolet & Camaro

Chevelle and Chevy II .............

Oil Pressure Indicator

Chevrolet & Camaro .............

Chevelle and Chevy II

Generator Indicator

Chevrolet & Camaro .

Chevelle and Chevy n ,

Hi-Beam Indicator

Chevrolet & Camaro <

Chevelle and Chevy II

Corvette , . • . ,

Directional Indicator

Chevrolet & Camaro

Chevelle & Chevy II . .

Corvette . .

Cigarette Lighter Lamp

Corvette .

Ignition Lock Lamp

Chevrolet . . .

Corvette . . .

Heater or A/C Control Panel

Chevrolet, Chevelle, Chevy n & Camaro . . .

Corvette . . .

Glove Box Lamps

Chevrolet, Chevelle, Chevy n & Camaro . . .

Corvette . . . . .

Dome and Courtesy Lamps

Cartridge Type (AU)

Bayonet Type (Exc. Corvette) . . .

Corvette ,

Convertible . .
37 1/2 Watts

55 Watts

37 1/2 Watts

55 Watts

45 Watts

4-32

4-32

4-32

Special Fiber

1

2

3

2

3

12

6

6

6
Optic
4002

4002

4001

6012

1157

1034-A

1157

1156

194

1895
.

1816

194

1895

194

1895

194

1895

194

1895

1445

194

1895

1816

1445

Wiring

1445

1895

1893

1895

1893

211

89,
212

90

631

CHEVROLET CHASSIS SERVICE MANUAL