manual radio set CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

CORVETTE BODY 1B-4

Fig.
3-Hood Spacing

vehicle as a unit by removing six screws around the

outer edge of opening, two screws retaining striker plate

and four screws which fasten compartment support to

cowl cross brace under dash. For parts identification

refer to Figure 6.

COWL AREA TRIM

Figure 7 illustrates instrument panel pads, cowl

"kick'.' panels, radio grille cover and console-to-dash

trim panel.

Figure 8 illustrates trim and moldings which are in-

stalled in the console area.

When installing instrument panel pads, it is advisable

to use new clips. Position of these clips upon installation

is illustrated in Figure 9.

REAR VIEW MIRROR

Outside

Removal

The outside rear view mirror may be removed from

the'
door by removing the set screw, located on the in-
board side of the mirror support, with an alien wrench.

Installation

Mirror may be installed by following the removal

procedures in reverse order. ,

Inside

Installation of inside mirror may be seen in Figure 10.

Tension of mirror stud may be adjusted by loosening or

tightening adjusting screw.

SUN VISOR

Attachment of sun visor assembly to windshield header

is made as shown in Figure 10. Turning adjusting screw

in increases friction.

COWL VENTILATOR ASSEMBLY

The following outline covers either the right of left

hand side. Refer to Figure 11.

Removal

1.
Disconnect positive cable from battery.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-23

condenser leak or to a defective connection. This

will cause burned points and ignition failure upon

initial starts and at high speeds.

4.
Capacity - Capacity is determined by the area of

the metallic elements and the insulating and im-

pregnating materials.

For a complete check of the condenser, use a tester

which will check for all of the above conditions. Follow

the instructions given by the manufacturer of the

test equipment. Condenser capacity should be
.18-:
23

microfarads.

REPLACEMENT

Four and Six Cylinder Engine Distributor (Fig. 4i)

1.
Release distributor cap hold-down screws, remove

cap and place it out of the work area.

2.
Remove rotor.

3.
Disconnect condenser lead wire from contact point

quick-disconnect terminal.

4.
Remove condenser attaching screw, lift.condenser

from breaker plate and wipe breaker plate clean.

5. Install new condenser using reverse of procedure

outlined above.

Eight Cylinder Engine Distributor

1.
Remove distributor cap.

2.
Loosen condenser lead attaching screw (fig. 6i) and

lift out condenser lead clip.

3.
Remove screw holding condenser bracket to breaker

plate and slide condenser from bracket.

4.
To replace condenser reverse the above procedure.

NOTE:
Make sure that new condenser lead is

installed in proper position (fig. 6i).

DISTRIBUTOR

(BREAKER POINT TYPE)

REMOVAL

1.
On radio equipped Corvettes, remove ignition shield

from over distributor and coil. One bolt is accessible

from top of shield, the other two are at rear of

shield, facing firewall.

2.
Release the distributor cap hold-down screws, re-

move the cap and place it clear of the work area.

NOTE:
If necessary, remove secondary leads

from the distributor cap after first marking the

cap tower for the lead to No. 1 cylinder. This

will aid in the reinstallation of leads in the cap.

3.
Disconnect the distributor primary lead from the coil

terminal.

4.
Scribe a realignment mark on the distributor bowl

and engine in line with the rotor segment.

5. Disconnect vacuum line to distributor and tachometer

drive cable (Corvette). Remove the distributor hold-

down bolt and elamp and remove the distributor from

the engine. Note position of vacuum advance mecha-

nism relative to the engine.

CAUTION: Avoid rotating the engine with the

distributor removed as the ignition timing will

be upset.
Rg.
121-L-6 Distributor-Exploded View

1.
Breaker Plate Attaching

Screws

2.
Condenser Attaching

Screws

3. Condenser

4.
Breaker Plate Assembly

4a.
Cam Lubricator

5. Vacuum Control Assembly

6. Vacuum Control

Attaching Screws

7. Housing

8. Cap

9. Rotor

DISASSEMBLY
10.
Contact Point

Attaching Screw

11.
Contact Point Assembly

12.
Weight Cover

Attaching Screws

13.
Weight Cover

14.
Weight Springs

15.
Advance Weights

16. Cam Assembly

17.
Main Shaft Assembly

18.
Roll Pin

19.
Drive Gear

It is advisable to place the distributor in a distributor

testing machine or synchroscope prior to disassembly.

CHEVROLET CU
SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-27

timing mark on pulley lines up with timing tab.

2.
Position distributor to opening in block in normal

installed attitude (fig. 15i), noting position of vacuum

control unit.

3.
Position rotor to point toward front of engine (with

distributor housing held in installed attitude), then

turn rotor counter-clockwise approximately 1/8 turn

more toward left cylinder bank and push distributor

down to engine camshaft. It may be necessary to ro-

tate rotor slightly until camshaft engagement is felt.

4.
While pressing firmly down on distributor housing,

kick starter over a few times to make sure oil pump

shaft is engaged. Install hold-down clamp and bolt

and snug up bolt.

5. Turn distributor body slightly until points just open

and tighten distributor clamp bolt.

6. Place distributor cap in position and check to see

that rotor lines up with terminal for No. 1 spark

plug.

7. Install cap, check all high tension wire connections

and connect spark plug wires if they have been re-

moved. It is important that the wires be installed in

their location in the supports.

NOTE:
The brackets are numbered to show the

correct installation. Wires must be installed as

indicated to prevent cross firing.

8. Connect vacuum line to distributor and distributor

primary wire to coil terminal.

9. Start engine and set timing as described under Turn-

Up in Section 6.

BREAKERLESS (MAGNETIC PULSE)

DISTRIBUTOR

REMOVAL (CORVETTE)

1.
If vehicle is equipped with radio, remove three bolts

securing ignition shield over distributor and coil.

One bolt is accessible from the top of shield, the

other two are at rear of shield, facing firewall.

2.
Disconnect tachometer drive cables from distributor

housing.

3.
Disconnect pickup coil leads at connector.

4.
Remove distributor cap.

5. Crank engine so rotor is in position to fire No. 1

cylinder and timing mark on harmonic balancer is

indexed with pointer.

6. Remove vacuum line from distributor.

7. Remove distributor clamping screw and hold-down

clamp.

8. Remove distributor and distributor-to-block gasket.

It will be noted that the rotor will rotate as the

distributor is pulled out of the block. Mark the re-

lationship of the rotor and the distributor housing

after removal so that the rotor can be set in the

same position when the distributor is being installed.

DISASSEMBLY (Fig. 16i)

NOTE:
If a distributor is being disassembled

for replacement of the stationary magnetic

pickup assembly only, it will be necessary to

perform only Steps 3, 4, 5, 7, 8, 9, and 12 of the

service procedure listed below.
1.
Remove screws securing rotor and remove rotor.

2.
Remove centrifugal weight springs and weights.

3.
Remove the tachometer drive gear from the distribu-

tor (Corvette only).

4.
Remove roll pin, then remove distributor drive gear

and washer.

CAUTION: To prevent

magnet, support drive gear
;e to the permanent

?n
driving out roll

pin.

5. Remove drive shaft assembly.

6. Remove centrifugal weight support and timer core

from drive shaft.

7. Remove connector from pickup coil leads.

8. Remove retaining ring which secures magnetic

core support plate to distributor shaft bushing in

housing.

9. As a unit, remove the entire magnetic pickup assem-

bly from the distributor housing.

10.
Remove brass washer and felt pad.

11.
Remove vacuum advance unit.

12.
To reassemble distributor, perform the above steps

in reverse order.

INSTALLATION (CORVETTE)

1.
Check to see that the engine is at firing position for

No.
1 cylinder (timing mark on harmonic balancer

indexed with pointer).

2.
Position a new distributor-to-block gasket on the

block.

3.
Before installing distributor, index rotor with hous-

ing as noted when distributor was removed. Install

distributor in block so that vacuum diaphragm faces

approximately 45° forward on the right side of the

engine and the rotor points toward contact in cap for

No.
1 cylinder.

4.
Replace distributor clamp leaving screw loose

enough to allow distributor to be turned for timing

adjustment.

5. Install spark plug wires in distributor cap. Place

wire for No. 1 cylinder in tower (marked on old cap

during disassembly) then install remaining wires

clockwise around the cap according to the firing

order (1-8-4-3-6-5-7-2).

6. Attach distributor to coil primary wires.

7. Replace distributor cap.

8. Adjust timing and then fully tighten distributor clamp

screw.

9. Attach vacuum line to distributor.

10.
Connect tachometer drive cables to distributor body.

11.
Replace ignition shields.

DISTRIBUTOR OFF-ENGINE TEST

The distributor's centrifugal and vacuum advance can

be checked in a distributor testing machine or synchro-

scope specially adapted or designed to accommodate this

type distributor. However, since this involves removing

the distributor from the engine, this test may be post-

poned until other system checks have been made. A dwell

reading cannot be obtained on this distributor and it is not

likely that the centrifugal or vacuum advance will be a

cause of trouble.

COIL REPLACEMENT

1.
Disconnect ignition switch and distributor leads from

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL-6Y-30

Fig.
2 li—Removing Ignition Switch Nut

4.
Remove heater and/or A/C control panel assembly

retaining screws and push panel assembly from

console.

NOTE: If interference between control panel

and radio is encountered, loosen radio retaining

nuts.

5.
Remove radio control knobs, bezels and retaining

nuts.

6. Disconnect radio wiring harness and antenna lead-in.

7.
Remove radio rear brace attaching screw and re-

move radio from vehicle.
Fig.
231—Switch and Connector Unplugged

8. Remove ignition switch bezel nut using Tool J-7607

and push switch rearward from panel opening.

9. Disconnect wiring connector from rear of switch.

10.
To install, reverse removal procedure.

SPARK PLUGS

CLEANING AND REGAPPING

Clean the spark plugs thoroughly, using an abrasive-

type cleaner. If the porcelains are badly glazed or

blistered, the spark plugs should be replaced. All spark

plugs must be of the same make and number or heat

range. Use a round feeler gauge to adjust the spark plug

gap to specifications (fig. 24i).

Fig.
22i—Unlocking Ignition Switch Connector

Fig.
241—Setting Sfxirk Plug Gap

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-27

Fig.
41 - Instrument Panel Installation — Chevelle

terminals from rear of cluster assembly (figs. 43

and 44).

12.
Remove four screws retaining upper section of dus-

ter housing to panel and remove cluster from the in-

strument panel and to a suitable working area for

necessary service (fig. 42).

Installation

1.
Position cluster assembly to rear of panel and install

four upper retaining screws.

2.
Connect cluster lamps, wiring connectors and wiring

harness assembly to the cluster assembly.

3.
Position instrument panel assembly into console

(hold panel at center and install center screws) and

install upper and lower retaining screws.

NOTE:
At this point temporarily reconnect

battery and check operation of cluster.

4.
Working under the console, install four lower screws

retaining lower section of cluster cover to rear of

panel.

5. Install radio brace screw at rear of radio.

6. Connect speedometer cable to speedometer and speed

warning device control knob.

7. Install A/C distributor duct and connect A/C hoses to

duct (if so equipped).

8. Install mast jacket upper support clamp.

9. Position steering shaft in the steering coupling and

install retaining bolt.

10.
Tighten mast jacket lower clamp (refer to Steering,

Section 9 for spring tension adjustment).

11.
Connect battery ground cable.

FUEL GAUGE AND/OR AMMETER

REPLACEMENT

1.
Disconnect battery ground cable.

2.
On air conditioned models, disconnect hose and re-

move air outlet from panel.

3.
Disconnect wiring connectors and cluster lamps from

rear of gauge assembly.

4.
Remove mounting plate retaining screws (3) and re-
move fuel gauge from rear of cluster housing.

5. Remove terminal nuts (3) securing gauge to template

and replace gauge.

6. To install, reverse the removal procedure.

CLOCK REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove clock set shaft knob retaining nut and knob.

3.
Disconnect wiring connector at clock terminal and

cluster lamp from clock housing. On A/C models,

disconnect hose from air distributor duct.

4.
Remove two screws retaining clock housing to

cluster cover and remove clock.

5. To install, reverse removal procedure.

SPEEDOMETER REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove instrument cluster assembly as previously

outlined in this section.

3.
Remove screws (8) attaching cover to rear of cluster

housing.

4.
Remove two screws attaching speedometer assembly

to cluster cover and carefully remove speedometer

head.

NOTE:
Servicing of the speedometer assembly

should be performed by an authorized
AC
speed-

ometer service station.

5. To install, reverse removal procedure.

SPEEDOMETER CABLE

Replacement or Lubrication

1.
Disconnect the speedometer cable from the speedom-

eter head. Remove the old cable by pulling it out

from speedometer
, end
of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

Fig.
42 - Instrument Cluster Installation

CHEVROLET CHASSIS SEtVKE MANUAL