reset CHEVROLET IMPALA 2000 8.G Owners Manual

yellowblue
2-14
Vehicle Customization Settings
Some of your vehicle's convenience features can be reset
or customized to perform according to your preference.
Customization cannot be changed with the AM
-FM Stereo
radio. See your dealer to have the settings changed. The
features you can program depend upon the options that
came with your vehicle. The following list shows the
features that can be reset or customized along with the
option you need to program that feature:

Settings (Available for All)

Oil Life Reset (Available for All)

Low Tire Pressure Reset (If Equipped)

Delayed Headlamp Illumination (Available for All)

Automatic Door Lock and Unlock (Available for All)

Remote Visual Verification (Available with Remote
Keyless Entry)

Remote Audible Verification (Available with Remote
Keyless Entry)

Content Theft Operation (If Equipped with Content
Theft System)
Trunk Jamb (If Equipped with Content Theft System)

Remote Keyless Entry Transmitter Programming
(Available with Remote Keyless Entry)

Horn Chirp On Timer (Available with Remote
Keyless Entry)

Return to Original Factory Settings (Available for All)

Exit Vehicle Customization Mode
To reset or customize your vehicle's features, you must
first enter the vehicle customization main menu.
To enter the main menu:
1. Turn the ignition to ACC or ON and the radio to off.
2. Press and hold the DISP button on the radio for at
least five seconds until SETTINGS is displayed.
3. Press the SEEK up or down arrows to scroll through
each available feature on your main menu.
4. Press the PREV or NEXT buttons to scroll through
the lower menu. An asterisk will appear next to the
item that is the current setting.

yellowblue
2-15
The following information shows how to reset or
customize features after entering the main menu:
SETTINGS
- Display Current Settings
OIL LIFE
- Oil Life Reset: This feature allows you to
reset the GM Oil Life System after an oil change, see
ªEngine Oilº in the Index. Be careful not to reset the OIL
LIFE accidentally at any time other than when the oil has
been changed. It can't be reset accurately until the next oil
change. To clear the CHANGE ENGINE OIL light from
the instrument cluster and reset the oil life monitor:
1. Scroll, using the SEEK up or down arrows, until OIL
LIFE appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. RESET will then be displayed.
3. Press the DISP button to reset. A chime will be heard
to verify the new setting and DONE will be
displayed for one second.
TIRE MON (Check Tire Pressure Reset): This feature
allows you to reset the tire pressure monitor after checking
all tire pressures, see ªTiresº in the Index. To clear the
LOW TIRE PRESSURE light from the instrument cluster
and reset the check tire pressure monitor:
1. Scroll, using the SEEK up or down arrows, until
TIRE MON appears on the display.2. Press the PREV or NEXT button to enter the
submenu. RESET will be displayed.
3. Press the DISP reset. A chime will be heard to
verify the new setting and DONE will be displayed
for one second.
LT DELAY (Delayed Headlamp Illumination): This
feature allows the vehicle's headlamps and parking lamps
to stay on for a fixed amount of time after exiting the
vehicle. To customize delayed headlamp illumination:
1. Scroll, using the SEEK up or down arrows, until
LT DELAY appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll, using the SEEK up or down arrows,
through the following options:

OFF
- Turns feature off.

30 SEC
- 30 seconds.

60 SEC
- 60 seconds.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.

yellowblue
2-18
TRNKJAMB (Trunk Jamb): This feature allows the
content theft system trunk lock sensor to be disabled or
enabled. To customize the trunk lock sensor:
1. Scroll, using the SEEK up or down arrows, until
TRNKJAMB appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

TRNK OFF
- Turns feature off.

TRNK ON
- Turns feature on.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
CHIRP (Horn Chirp Timer): This feature allows you
to choose between short or long horn chirp sounds
when the remote keyless entry transmitter is used.
To customize the length of horn chirps:
1. Scroll until CHIRP appears on the display.2. Press the PREV or NEXT button to enter the
submenu. Scroll through the following options:

SHORT
- Short Chirp (16 msec)

LONG
- Long Chirp (32 msec)
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
ORIG SET (Return to the Original Settings): This
feature allows you to return all feature customization
settings back to their original factory settings. To reset:
1. Scroll until ORIG SET appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. Scroll through the following options:

SET ALL
- Returns to factory settings.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.

yellowblue
2-40 Windshield Wipers
When the ignition key is in ACC or ON, you control the
windshield wipers by turning the band marked WIPER.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
For steady wiping at low speed, turn the band to LO. For
high
-speed wiping, turn the band further, to HI. To stop
the wipers, turn the band to OFF.
You can set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain or
snow. Turn the band to choose the delay time. The
closer to LO, the longer the delay between wipes.
Be sure to clear ice and snow from the wiper blades
before using them. If they're frozen to the windshield,
carefully loosen or thaw them. If your blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
Windshield Washer
At the top of the multifunction lever, there's a paddle
with the word PUSH on it. To spray washer fluid on the
windshield, push the paddle. The wipers will run for
several sweeps and then either stop or return to your
preset speed. Note: the ignition key must be in ACC or
ON to for this to work. See ªWindshield Washer Fluidº
in the Index.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
The LOW WASHER
FLUID message on your
instrument panel cluster
will appear when the fluid
level is low.

yellowblue
2-42
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don't need to reset it.
Once you're going about
25 mph (40 km/h) or more,
press the RESUME button
on your steering wheel.
You'll go right back up to
your chosen speed and
stay there.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the SET button on the steering wheel, then
release the button and the accelerator pedal. You'll
now cruise at the higher speed.
Press the ACCEL button on the steering wheel. Hold it
there until you get up to the speed you want and then
release the button. (To increase your speed in very small
amounts, press the ACCEL button for less than half a
second and then release it. Each time you do this, your
vehicle will go 1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you set the
cruise control speed by pressing the SET button on the
steering wheel.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST button on the steering wheel until
you reach the lower speed you want, then release it.

To slow down in very small amounts, press the
COAST button on the steering wheel for less than a
half second. Each time you do this, you'll go 1 mph
(1.6 km/h) slower.

yellowblue
2-61 Speedometer and Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h). Your
odometer shows how far your vehicle has been driven in
either miles (used in the United States) or in kilometers
(used in Canada).
Your vehicle has a tamper
-resistant odometer. If you see
ERROR, you'll know someone has probably tampered
with it and the numbers may not be accurate.
You may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to the
mileage total of the old odometer, then that will be done.
But if it can't, then it will be set at zero and a label must
be put on the driver's door to show the old mileage
reading when the new odometer was installed.
Trip Odometer
Your trip odometer tells how far you have driven since
you last reset it.
Your trip/select reset switch will go back and forth
between the odometer and the trip odometer if the
button is pressed and released within 1.5 seconds. If the
button is pressed and held for longer than 1.5 seconds
while in the trip odometer mode, it will be reset to zero.If the button is pressed and held for longer than
1.5 seconds while in the odometer mode, it will have
no effect.
Your trip odometer will work no matter what position
your key is in, and even if the key isn't in.Tachometer (If Equipped)
The tachometer displays the
engine speed in thousands
of revolutions per minute
(rpm). (Optional cluster
tachometer shown.)
NOTICE:
Do not operate the engine with the tachometer in
the red area, or engine damage may occur.

yellowblue
2-65 Anti-Lock Brake System Warning
Light (Option)
The anti-lock brake system warning light should come on
for a few seconds when you turn the ignition key to ON.
If the anti
-lock brake system warning light stays on longer
than normal after you've started your engine, turn the
ignition off. Or, if the light comes on and stays on when
you're driving, stop as soon as possible and turn the
ignition off. Then start the engine again to reset the
system. If the light still stays on, or comes on again while
you're driving, the anti
-lock brake system needs service
and you don't have anti
-lock brakes. The brake pedal may
be harder to push, or it may go to the floor. It may take
longer to stop. Adjust your driving accordingly.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to ON. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
Traction Control System Warning Light
(3800 V6 Engine)
The traction control system warning light may come on
for the following reasons:

If you turn the system off by pressing the traction
control button located on the instrument panel, a
chime will sound and the warning light will come on
and stay on. To turn the system back on, press the
button again. The warning light should go off.
(See ªTraction Control Systemº in the Index for
more information.)

If there's a brake system problem that is specifically
related to traction control, the traction control system
will turn off and the warning light will come on. If
your brakes begin to overheat, the traction control
system will turn off and the warning light will come
on until your brakes cool down.

yellowblue
2-74
CHANGE ENGINE OIL
This message is displayed
when the engine oil needs to
be changed.
When you change the engine oil, be sure to reset the GM
Oil Life System See ªEngine Oil, When to Changeº in
the Index.
DOOR AJAR
This message will appear if
the driver's door or one of
the passenger's doors is not
completely closed and the
ignition is ON. If you are in
a forward or reverse gear
position you will also hear
four chimes.SECURITY
This message is
displayed to monitor the
Passlock

System.
If the security message is displayed continuously while
driving and stays on, there may be a problem with the
Passlock

System. Your vehicle will not be protected by
Passlock, and you should see your dealer.
LOW FUEL
This message is displayed
when your vehicle is low
on fuel. Four chimes will
also sound.
Refer to the fuel gage for a better indication of the
amount of fuel remaining in the fuel tank.

yellowblue
2-75
LOW WASHER FLUID
This message is displayed
when the vehicle is low on
windshield washer fluid.
The message is only
displayed for 60 seconds
at the start of each
ignition cycle.
For more information see, ªWindshield Washer Fluidº in
the Index.LOW TIRE PRESSUREThe low tire pressure
system monitors the
inflation pressure of your
vehicle's tires.
If one or more of the tires is low, the LOW TIRE
PRESSURE message in the systems monitor will be
displayed and a warning chime will sound.
When you have checked the tire pressures, be sure to
reset the tire pressure monitor. See ªTiresº in the Index.

yellowblue
2-77
Driver Information
Center (DIC) (Option)
Sunroof (Optional) Version Shown
The DIC will show information about the vehicle and
the surroundings.

RESET (Reset Button):
You can reset the AVG ECON, FUEL USED or
AVG SPEED trip computer modes by pressing and
holding this button for three seconds while you are in
the mode you wish to reset.To change the display to a metric or English reading,
press and hold the RESET and MODE buttons for
three seconds.

The reset button can be used to set the compass zone
variation. See ªCompass Varianceº in the Index.

The reset button can also be used to manually
calibrate the compass. See ªManual Compass
Calibrationº in the Index.

MODE (Mode Button): Press this button to cycle
through three modes of operation
-- Off,
Compass/Temperature and Trip Computer mode.
In the Trip Computer mode, pressing the MODE
button cycles through the five displays. Press the
MODE button after the last Trip Computer display to
return the DIC to the OFF mode.
Off: No driver information is displayed in this mode
of operation.
Compass/Temperature Mode: One of eight compass
readings and the outside temperature are displayed. If
the temperature is below 38F (3C), the temperature
reading will toggle between displaying the outside
temperature and the word ªICEº for two minutes.