fuel type CHEVROLET KODIAK 2007 Owners Manual

What Fuel to Use in Canada
Canadian fuels are blended for seasonal changes.
Diesel Type “A” fuel is blended for better cold
weather starting (below 0°F or−18°C); however,
you may notice some power and fuel economy
loss. If Type “A” fuel is used in warmer
temperatures, stalling and hard starting may
occur. Diesel Type “B” fuel is blended for
temperatures above 0°F (−18°C).
It is important that diesel-powered trucks are
refueled only with ultra low-sulfur fuel. The
emission control system requires the use of diesel
fuel with ultra low-sulfur (0.0015% by weight, or
15 ppm, maximum) content. Both ultra low-sulfur
and higher sulfur diesel fuels are available in
the United States. Use of fuels with higher-sulfur
content will affect the function of the emission
components and may cause reduced performance,
excessive smoke, and unpleasant odor.
At a minimum, the diesel fuel you use should
meet the latest version of specification
CAN/CGSB-3.517 (Low Sulfur Diesel) in Canada.
In addition, the Engine Manufacturers Association
(EMA) has identified properties of an improved
diesel fuel for better engine performance and
durability (FQP-1A). Diesel fuels corresponding tothe EMA description could provide better starting,
less noise, and better vehicle performance. If
there are questions about the fuel you are using,
contact your fuel supplier.
If your vehicle has the 6.6L engine, it is acceptable
to use diesel fuel containing up to 5% biodiesel
(B5), but the final blended fuel must meet the same
specification, CAN/CGSB-3.517 (Low Sulfur Diesel)
in Canada, as other fuels used in your vehicle, and
the biodiesel used for making this fuel must meet
the latest version of ASTM specification D 6751.
Biodiesel is produced from vegetable oils or animal
fat that have been chemically modified to reduce
the possibility of damage to your fuel system and
engine. Higher concentration (i.e., greater than B5)
biodiesel-containing fuels or the use of unmodified
bio-oils blended into diesel fuel at any concentration
is not recommended and could damage your fuel
system and engine. Such damage would not be
covered by your warranty. If there are questions
about the biodiesel-containing fuels you are using,
contact your fuel supplier.
255

{CAUTION:
If you get fuel on yourself and then
something ignites it, you could be badly
burned. Fuel can spray out on you if you
open the fuel cap too quickly. This spray
can happen if your tank is nearly full, and is
more likely in hot weather. Open the fuel
cap slowly and wait for any “hiss” noise to
stop. Then unscrew the cap all the way.
When you put the cap back on, turn it clockwise
until it is tight.
Notice:If you need a new fuel cap, be sure to
get the right type. Your dealer can get one
for you. If you get the wrong type, it may not
t properly. This may cause your malfunction
indicator lamp to light and may damage
your fuel tank and emissions system. See
Malfunction Indicator Lamp on page 174.If you have dual tanks, fill the driver’s side tank, or
forward tank, first. The fuel gage will give better
readings this way. Your gage will show the
total fuel left in both tanks.
If your vehicle is a C4/C5 model and you have
dual tanks, the engine must be off when refueling
or the fuel transfer system may become
inoperable.
If you have a single tank with dual fillers, where
there is a filler on each side of the vehicle, do not
attempt to fill the tank through both fillers at the
same time. Also, do not fill the tank with both caps
removed, as this may result in over-filling the
tank and fuel spillage.
265

Other Service Items
Fuel Filter
Fuel Filter/Pressure Regulator
(Gasoline Engines)
The steel fuel filter/pressure regulator is located
near the engine compartment on the driver’s
side frame rail. If your vehicle has a rear steel fuel
tank, the fuel filter/pressure regulator is located
near the rear fuel tank, on the driver’s side frame
rail. SeeScheduled Maintenance on page 363
for recommended service intervals.
If your vehicle is equipped with the optional Davco
spin-on type filter, it is located on the driver’s
side frame rail.
Fuel Filter (Diesel Engines)
If you have a diesel engine, your fuel filter is
located in the engine compartment on the driver’s
side of the vehicle, or along the driver’s side
frame rail. See “Fuel Filter Replacement” earlier in
this section for further information.
Also seeScheduled Maintenance on page 363for
recommended service intervals.
Primary Fuel Filter and Water
Separator
If you have a diesel
engine, you may have
this spin-on filter. It
is located on the driver’s
side frame rail.
It has a clear plastic drain bowl at the bottom.
Check the drain bowl occasionally for any water or
particles.
To drain the bowl, do the following:
1. Shut off the engine.
2. Partially open the drain valve at the bottom of
the filter.
SeeEngine Oil (Caterpillar
®Diesel Engine) on
page 268orEngine Oil (Gasoline Engine) on
page 268orEngine Oil (DURAMAX
®/Isuzu Diesel
Engine) on page 272for proper disposal
procedures.
317

Ination - Tire Pressure
The Certification or Tire Information label shows
the correct inflation pressures for your tires
when they are cold. Cold means your vehicle has
been sitting for at least three hours or driven
no more than 1 mile (1.6 km).
Notice:Do not let anyone tell you that
under-ination or over-ination is all right. It is
not. If your tires do not have enough air
(under-ination), you can get the following:
Too much exing
Too much heat
Tire overloading
Premature or irregular wear
Poor handling
Reduced fuel economy
If your tires have too much air (over-ination),
you can get the following:
Unusual wear
Poor handling
Rough ride
Needless damage from road hazards
When to Check
Check your tires once a month or more.
Also, check the tire pressure of the spare tire if
your vehicle has one.
How to Check
Use a good quality pocket-type gage to check tire
pressure. You cannot tell if your vehicle’s tires
are properly inflated simply by looking at
them. Radial tires may look properly inflated even
when they are underinflated.
Be sure to put the valve caps back on the valve
stems. They help prevent leaks by keeping out dirt
and moisture.
322

Relay Usage
ECU/PTO*Engine Control Unit/Power Take-Off
*Diesel 7.8 DURAMAX
®
BRK LAMPC4/C5 Brake Lamps,
C6/C7/C8 Tractor/Trailer Wiring
DRL Daytime Running Lamps
IGN-4 Ignition
CHMSL Center High Mounted Stoplamp
MRK LTS Sidemarker and Clearance Lamps
HTD/MIRR Heated Mirrors
HTR Diesel Heated Fuel
RT TRN TRLR Passenger’s Side Trailer Turn Signal
Blank Not Used
LT TRN TRLR Driver’s Side Trailer Turn Signal
Blank Not Used
Blank Not Used
Blank Not Used
Underhood Fuse Block
When a circuit goes out, the problem could be in
either the primary or secondary underhood
fuse blocks. These blocks use blade-type fuses.
Both underhood fuse blocks are located in
the engine compartment, on the passenger’s side
of the vehicle.
To access the fuse blocks, gently squeeze both
sides of the cover to unlatch the tabs at the
top. Then, unsnap both attachments at the bottom
and remove the cover.
Be sure to replace fuses with fuses of the same
rating. Do not use fuses of higher amperage
than those indicated on the fuse block.
344

Engine Specications
Engine RPO Type
6.6L V8 DURAMAX
®LLY Common Rail Fuel System
7.2L L6 Caterpillar
®C7 LG5Hydraulic/Electronic Unit Injector
Fuel System
7.8L Isuzu 6H LG4 Common Rail Fuel System
8.1L V8 VORTEC™ L18Single Port Fuel Injector Fuel
System
Normal Maintenance Replacement Parts
Replacement parts identified by name, part number, or specification can be obtained from your dealer.
Part GM Part Number ACDelco®Part Number
Air Compressor Filter
Haldex compressor (8.1L Engine Only)88915425 A507CF
Engine Air Cleaner/Filter
6.6L; 8.1L (C4/C5 Models) 88937527 A2032C
7.2L; Isuzu 6H (C6/C7/C8 Models) with Standard
Air Cleaner88937525 A2031C
7.2L; Isuzu 6H (C6/C7/C8 Models) with Heavy Duty
Air Cleaner88937525
1A2031C
8.1L (C6/C7/C8 Models) with Heavy Duty Air Cleaner 88937525 A2031C
8.1L (C6/C7/C8 Models) with Standard Air Cleaner 88937545 A2034C
352

30,000 Miles (48 000 km)
❑Gasoline Engine Only: Check engine oil life
system. If engine oil and filter are changed,
reset system. See “Engine Oil (Gasoline
Engine)” in the Index.(2) (8)
❑6.6L DURAMAX
®Diesel Without Engine Oil
Life System Only: Change engine oil and
filter (or every 12 months, or every 750 hours
of engine operation, whichever occurs first).(2)
❑6.6L DURAMAX
®Diesel With Engine Oil
Life System Only: Check oil life system.
If engine oil and filter are changed, reset
system. See “Engine Oil (DURAMAX
®/Isuzu
Diesel)” in the Index.(2) (9)
❑Check fluid levels (or every 3 months,
whichever occurs first).(1) (5)
❑Gasoline Engine: Inspect engine air cleaner
filter. If necessary, replace the filter. If vehicle
is driven in dusty/dirty conditions, inspect
filter at every engine oil change. SeeEngine
Air Cleaner/Filter on page 280for more
information.❑Diesel Engine: Inspect engine air cleaner filter
change indicator. If necessary, replace the
filter. If vehicle is driven in dusty/dirty conditions,
inspect filter change indicator at every engine
oil change. SeeEngine Air Cleaner/Filter
on page 280for more information.
❑DURAMAX
®/Isuzu Diesel Only: Replace fuel
filter (or every 750 hours of engine operation,
whichever occurs first).
❑Chassis lubrication service (or every 6 months,
whichever occurs first).(11)
❑Replace fuel filter(s) (or every 12 months,
whichever occurs first).(2)
❑Steering system service.(12)
❑Front and rear suspension service.(13)
❑Spring-to-axle U-bolts and shackle bolts
service.(15)
❑Exhaust system service (or every 6 months,
whichever occurs first).(2) (3) (16)
❑Wheel bearing (grease type) service (and
whenever hubs are removed).(22) (36)
❑Wheels and tires service.(14)
❑Hydraulic brake service (or every 6 months,
whichever occurs first).(6) (36)
368

❑Isuzu 6H Diesel With Engine Oil Life System
Only: Check oil life system (or every 12 months,
or every 600 hours of engine operation,
whichever occurs first). If engine oil and filter
are changed, reset system. See “Engine Oil
(DURAMAX
®/Isuzu Diesel)” in the Index.(2) (7)
❑Gasoline Engine Only (Vehicles with
GVW greater than 16,000 lbs): Spark plug
service.(2) (25)
❑Check fluid levels (or every 3 months,
whichever occurs first).(1) (5)
❑Gasoline Engine: Inspect engine air cleaner
filter. If necessary, replace the filter. If vehicle
is driven in dusty/dirty conditions, inspect filter
at every engine oil change. SeeEngine Air
Cleaner/Filter on page 280for more information.
❑Diesel Engine: Inspect engine air cleaner filter
change indicator. If necessary, replace the filter.
If vehicle is driven in dusty/dirty conditions,
inspect filter change indicator at every engine
oil change. SeeEngine Air Cleaner/Filter
on page 280for more information.
❑DURAMAX
®/Isuzu Diesel Only: Replace fuel
filter (or every 750 hours of engine operation,
whichever occurs first).❑Chassis lubrication service (or every 6 months,
whichever occurs first).(11)
❑Replace fuel filter(s) (or every 12 months,
whichever occurs first).(2)
❑Inspect door hinge pins and bushings and
replace as necessary.
❑Steering system service.(12)
❑Front and rear suspension service.(13)
❑Spring-to-axle U-bolts and shackle bolts
service.(15)
❑Exhaust system service (or every 6 months,
whichever occurs first).(2) (3) (16)
❑Wheel bearing (grease type) service (and
whenever hubs are removed).(22) (36)
❑Wheels and tires service.(14)
❑Hydraulic brake service (or every 6 months,
whichever occurs first).(6) (36)
❑Parking brake service (or every 6 months,
whichever occurs first).(21)
374

❑Cooling system service. Clean the cooling
system filler cap with clean water, clean
the core, pressure test the cap and the
system for proper pressure capability, and
inspect condition of cooling and heater
hoses and clamps. Replace hoses if cracked,
swollen, or damaged.
❑Replace fuel filter(s) (or every 12 months,
whichever occurs first).(2)
❑Steering system service.(12)
❑Front and rear suspension service.(13)
❑Spring-to-axle U-bolts and shackle bolts
service.(15)
❑Exhaust system service (or every 6 months,
whichever occurs first).(2) (3) (16)
❑Inspect door hinge pins and bushings and
replace as necessary.
❑Wheel bearing (grease type) service (and
whenever hubs are removed).(22) (36)
❑Wheels and tires service.(14)
❑Hydraulic brake service (or every 6 months,
whichever occurs first).(6) (36)
❑Parking brake service (or every 6 months,
whichever occurs first).(21)❑Air brake service (or every 6 months, whichever
occurs first).(32)
❑Air brake automatic slack adjuster service (or
every 500 hours, whichever occurs first).(33)
❑Check air brake relay valve operation and check
for leaks (or every month, or every 300 hours,
whichever occurs first).
❑Clean air brake application valve (or every
3 months, or every 300 hours, whichever
occurs first). Lubricate linkage.
❑Air brake chamber service (or every 2 months,
whichever occurs first).(34)
❑Air brake system valve service (or every
3 months, or every 900 hours, whichever
occurs first).(37)
❑C600, C700, and C800 Gasoline Engines
Only: Engine drive belts service (or every
12 months, whichever occurs first).(17)
❑Thermostatically controlled engine cooling
fan service.(3) (19)
❑Shields and underhood insulation
service.(3) (4) (20)
❑Rear axle air shift motor service.(10)
380

(22)= Wheel bearing service:
•Grease type — Clean, inspect, and lubricate
with the proper wheel bearing grease at
designated intervals or when hubs are
removed. SeePart C: Recommended Fluids
and Lubricants on page 397.
•Oil-filled type — Some wheel bearings are
lubricated by axle lubricant. When you
have oil-filled hubs, use lubricant identical
to that used in the axle. Lubricant change
intervals are the same for front and rear
axles. However, you must maintain the proper
oil level between change intervals. See
Front Wheel Bearings with Oil-Filled Hubs
on page 319andPart C: Recommended
Fluids and Lubricants on page 397.
(23)= Check the air intake system installation
to see that gaskets are seated properly and
all hose connections, fasteners, and other
components are tight. Tighten connections
and fasteners or replace parts as required.(24)= Evaporative Control System Service,
if equipped: Check all fuel and vapor lines and
hoses for proper connections and correct routing
(or every 24 months, whichever occurs first).
Replace parts as needed.
(25)= Replace spark plugs. Inspect wires for
damage. Check the wire boot and boot heat
shield fit at spark plugs and coil. Replace parts
as needed.
(26)= Check the fuel tank, fuel cap and fuel lines
for damage which could cause leakage. Inspect
fuel cap for correct sealing ability and any
indications of damage. Check fuel cap gasket
for even filler neck imprint. Replace parts as
needed.
(27)= Check Exhaust Gas Recirculation (EGR)
system as described in the service manual.
SeeService Publications Ordering Information
on page 415.
388