Engine light CHRYSLER 300 2007 1.G Owner's Guide

5. Connect one end of the jumper cable to the remote
jump-start positive battery post(+)in the engine com-
partment. Connect the other end of the same cable to the
positive terminal of the booster battery. Refer to the
following illustration for jump-starting connections.
6. Connect the other cable, first to the negative terminal
of the booster battery andthen to the engine ground (-)
of the vehicle with the discharged battery.Make sure
you have a good contact on the engine ground. Refer to
the following illustration for jump-starting connections.WARNING!
•You should not try to start your vehicle by push-
ing or towing.
•Do not connect the cable to the negative post of
the discharge battery. The resulting electrical
spark could cause the battery to explode.
•During cold weather when temperatures are be-
low freezing point, electrolyte in a discharged
battery may freeze. Do not attempt jump-starting
because the battery could rupture or explode. The
battery temperature must be brought up above
freezing point before attempting jump-start.
7. Start the engine in the vehicle that has the booster
battery. Let the engine idle a few minutes. Then, start the
engine in the vehicle with the discharged battery.
NOTE:For vehicles equipped with ESP, refer toSyn-
chronizing ESPunderElectronic Stability Programin
Section 5 of this manual if the ESP/BAS light (in the
instrument cluster) remains on continuously after start-
ing the engine of the vehicle with the discharged battery.
Jump-Starting
WHAT TO DO IN EMERGENCIES 323
6

▫Windshield Washers/Headlight Washers — If
Equipped...........................347
▫Exhaust System......................348
▫Cooling System.......................349
▫Hoses And Vacuum/Vapor Harnesses.......353
▫Fuel System.........................354
▫Brake System........................354
▫Automatic Transmission................356
▫All Wheel Drive (AWD) — If Equipped.....358
▫Front And Rear Wheel Bearings...........358
▫Appearance Care And Protection From
Corrosion...........................359
▫Cleaning The Center Console Cup Holders —
300 Models..........................362
▫Cleaning The Center Console Cup Holders —
300C And 300 Touring Models............363
Fuses (Power Distribution Centers).........363
▫Fuses (Front Power Distribution Center).....363▫Fuses (Rear Power Distribution Center)......366
Vehicle Storage........................370
Replacement Bulbs.....................371
Bulb Replacement......................372
▫Low Beam Headlight, High Beam Headlight,
Park/Turn Light, Inner Park Light, And Outer
Park Light – 300 Models................372
▫Low Beam Headlight, High Beam Headlight,
And Park/Turn Light – 300C.............374
▫Backup Light, Side Marker Light, And Tail/Stop
Turn Light — 300 Models...............376
▫Tail/Stop, Tail, Turn Signal Light, And Backup
Light — 300C Models..................378
▫License Light........................381
Fluids And Capacities...................382
Fluids, Lubricants, And Genuine Parts......383
▫Engine.............................383
▫Chassis............................384
328 MAINTAINING YOUR VEHICLE

ONBOARD DIAGNOSTIC SYSTEM — OBD II
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBD II. This system monitors
the performance of the emissions, engine, and automatic
transmission control systems. When these systems are
operating properly, your vehicle will provide excellent
performance and fuel economy, as well as engine emis-
sions well within current government regulations.
If any of these systems require service, the OBD II system
will turn on the “Malfunction Indicator Light.” It will
also store diagnostic codes and other information to
assist your service technician in making repairs. Al-
though your vehicle will usually be drivable and not
need towing, see your dealer for service as soon as
possible.CAUTION!
Prolonged driving with the “Malfunction Indicator
Light” on could cause further damage to the emis-
sion control system. It could also affect fuel economy
and driveability. The vehicle must be serviced before
any emissions tests can be performed.
If the “Malfunction Indicator Light” is flashing
while the engine is running, severe catalytic con-
verter damage and power loss will soon occur. Im-
mediate service is required.
Loose Fuel Filler Cap
If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, a
“Check Gascap” message will display in the Electronic
Vehicle Information Center (EVIC) — if equipped. If this
occurs, tighten the fuel filler cap properly and press the
odometer reset button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.
332 MAINTAINING YOUR VEHICLE

A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states, which have an I/M (Inspection and
Maintenance) requirement, this check verifies the
following: the MIL (Malfunction Indicator Lamp)
is functioning and is not on when the engine is running,
and that the OBD (On Board Diagnostic) system is ready
for testing.
Normally, the OBD system will be ready. The OBD
system maynotbe ready if your vehicle was recently
serviced, if you recently had a dead battery, or a battery
replacement. If the OBD system should be determined
not ready for the I/M test, your vehicle may fail the test.Your vehicle has a simple ignition key actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD system is ready, you must do
the following:
1. Insert your ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn your key to the ON position, you
will see your MIL symbol come on as part of a normal
bulb check.
5. Approximately 15 seconds later, one of two things will
happen:
a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn off
the ignition key or start the engine. This means that
your vehicle’s OBD system isnot readyand you
shouldnotproceed to the I/M station.
MAINTAINING YOUR VEHICLE 333
7

The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant or equivalent directly into the lock
cylinder.
Windshield Wiper Blades
The rubber edges of the wiper blades and the windshield
should be cleaned periodically with a sponge or soft cloth
and a mild nonabrasive cleaner. This will remove accu-
mulations of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
Windshield Washers/Headlight Washers — If
Equipped
The windshield washer and the headlight washer (if
equipped) share the same fluid reservoir. The fluid
reservoir is located in the front of the engine compart-
ment on the passenger side of the vehicle. Be sure to
check the fluid level in the reservoir at regular intervals.
Fill the reservoir with windshield washer solvent (not
radiator antifreeze) and operate the system for a few
seconds to flush out the residual water.
The fluid reservoir will hold nearly 1 gallon (4 liters) of
washer fluid when the message “Low Washer Fluid”
appears in the Electronic Vehicle Information Center
(EVIC) — if equipped.
WARNING!
Commercially available windshield washer solvents
are flammable. They could ignite and burn you. Care
must be exercised when filling or working around
the washer solution.
MAINTAINING YOUR VEHICLE 347
7

Insure nylon tubing in these areas has not melted or
collapsed.
Inspect all hose connections such as clamps and cou-
plings to make sure they are secure and no leaks are
present.
NOTE:
•
Often, fluid such as oil, power steering fluid, and
brake fluid are used during assembly plant operations
to facilitate the assembly of hoses to couplings. There-
fore, oil wetness at the hose-coupling area is not
necessarily an indication of leakage. Actual dripping
of hot fluid when systems are under pressure (during
vehicle operation), should be noted before a hose is
replaced based on leakage.
•Inspect the brake hoses whenever the brake system is
serviced and at every engine oil change. Inspect hy-
draulic brake hoses for surface cracking, scuffing, or
worn spots. If there is any evidence of cracking,
scuffing, or worn spots, the hose should be replaced
immediately! Eventual deterioration of the hose can
take place resulting in a possibility of a burst failure.
WARNING!
Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
Master Cylinder - Brake Fluid Level Check
Check the fluid level in the master cylinder immediately
if the brake system warning light indicates system fail-
ure.
Check the fluid level in the master cylinder when per-
forming underhood services.
Clean the top of the master cylinder area before removing
the cap. Add fluid to bring the level up to the top of the
“FULL” mark on the side of the master cylinder reservoir.
Overfilling of fluid is not recommended because it may
cause leaking in the system.
MAINTAINING YOUR VEHICLE 355
7

At Each Stop for Fuel
•
Check the engine oil level about 5 minutes after a fully
warmed engine is shut off. Checking the oil level while
the vehicle is on level ground will improve the accu-
racy of the oil level reading. Add oil only when the
level is at or below the ADD or MIN mark.
•Check the windshield washer solvent and add if
required.
Once a Month
•
Check tire pressure and look for unusual wear or
damage.
•Inspect the battery, and clean, and tighten the termi-
nals as required.
•Check the fluid levels of coolant reservoir and brake
master cylinder, and add as needed.
•Check all lights and all other electrical items for correct
operation.
•Check rubber seals on each side of the radiator for
proper fit.
At Each Oil Change
•
Change the engine oil filter.
•Inspect the exhaust system.
•Inspect the brake hoses.
•Inspect the CV joints and front and rear suspension
components.
•Check the coolant level, hoses, and clamps.
388 MAINTENANCE SCHEDULES
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S

ABS (Anti-Lock Brake System)............. 253
Adaptive Cruise Control (ACC)
(Cruise Control)........................ 121
Adding Engine Coolant (Antifreeze)......... 351
Adding Fuel.......................... 293
Adding Washer Fluid.............. 112,114,347
Adjustable Pedals....................... 117
Air Cleaner, Engine
(Engine Air Cleaner Filter)................ 341
Air Conditioner Maintenance.............. 344
Air Conditioning....................219,221
Air Conditioning Controls................ 219
Air Conditioning Filter................227,345
Air Conditioning, Operating Tips........... 228
Air Conditioning Refrigerant...........344,345
Air Conditioning System...........219,221,344
Air Pressure, Tires...................169,272
Airbag................................ 41
Airbag Deployment....................45,47
Airbag Light....................46,49,60,165
Airbag Maintenance...................... 48
Airbag, Side........................... 46
Airbag, Window (Side Curtain)...........42,46Alarm (Security Alarm).................. 168
Alarm System (Security Alarm)............. 15
Alignment and Balance.................. 278
All Wheel Drive (AWD)...............250,358
Alterations/Modifications, Vehicle............ 7
Antenna, Satellite Radio.................. 214
Antifreeze (Engine Coolant).........350,351,382
Disposal............................ 352
Anti-Lock Brake System (ABS)............. 253
Anti-Lock Warning Light..............164,255
Anti-Theft Security Alarm (Theft Alarm)...... 15
Anti-Theft System...................... 168
Appearance Care....................... 359
Auto Down Power Windows............... 28
Auto Up Power Windows................. 28
Automatic Dimming Mirror................ 68
Automatic Door Locks..................24,25
Automatic Headlights................... 103
Automatic Temperature Control (ATC)....... 221
Automatic Transaxle
Special Additives..................... 357
Automatic Transmission.........240,245,356,357
Adding Fluid.....................
357,384
414 INDEX

Autostick........................... 249
Fluid and Filter Changes................ 357
Fluid Change........................ 357
Fluid Level Check..................... 356
Fluid Type.......................... 384
Gear Ranges......................... 241
Shifting..........................240,245
Special Additives..................... 357
Torque Converter..................... 243
Automatic Transmission Limp Home Mode . . . 244
Autostick..........................247,249
Ball Joints............................ 346
Battery............................... 343
Emergency Starting.................... 322
Jump Starting........................ 322
Keyless Transmitter Replacement (RKE)..... 21
Location.........................322,343
Bearings.............................. 358
Belts, Drive........................... 340
Belts, Seat............................. 33
Body Mechanism Lubrication.............. 346
B-Pillar Location....................... 267Brake Assist System..................... 258
Brake, Parking......................... 251
Brake System.......................253,354
Anti-Lock (ABS)...................... 253
Fluid Check......................355,384
Hoses.............................. 354
Master Cylinder...................... 355
Parking............................ 251
Warning Light....................165,253
Brakes............................... 253
Brake/Transmission Interlock.............. 240
Break-In Recommendations, New Vehicle...... 58
Bulb Replacement...................... 372
Bulbs, Light........................... 371
Calibration, Compass.................... 178
Capacities, Fluid....................... 382
Caps, Filler
Fuel............................... 293
Oil (Engine)......................338,339
Radiator (Coolant Pressure).............. 351
Car Washes........................... 359
Carbon Monoxide Warning.............59,292
INDEX 415
10

Cassette Tape and Player Maintenance....... 217
Catalytic Converter..................... 341
CD (Compact Disc) Player.............188,195
Cellular Phone.......................... 72
Chains, Tire........................... 279
Changing A Flat Tire.................... 314
Chart, Tire Sizing....................... 264
Check Engine Light
(Malfunction Indicator Light).............. 333
Child Restraint...................50,52,55,56
Child Restraint Tether Anchors...........54,55
Child Safety Locks....................... 25
Clean Air Gasoline...................... 290
Cleaning
Wheels............................. 360
Climate Control........................ 219
Clock.......................186,190,196,207
Compact Disc (CD) Maintenance........... 218
Compact Spare Tire..................... 274
Compass............................. 178
Compass Calibration.................... 178
Compass Variance...................... 179
Computer, Trip/Travel................... 175Console.............................. 153
Console, Floor......................... 153
Console, Overhead...................... 140
Contract, Service....................... 408
Coolant Pressure Cap (Radiator Cap)........ 351
Cooling System........................ 349
Adding Coolant (Antifreeze)............. 351
Coolant Capacity..................... 382
Coolant Level.....................349,352
Disposal of Used Coolant............... 352
Drain, Flush, and Refill................. 350
Inspection........................... 352
Points to Remember................... 352
Pressure Cap........................ 351
Radiator Cap........................ 351
Selection of Coolant (Antifreeze)....350,382,383
Cruise Control (Speed Control).......... 118,121
Cruise Light........................... 163
Cup Holder.....................151,362,363
Customer Assistance.................... 406
Data Recorder, Event..................... 49
Daytime Running Lights................. 106
416 INDEX