tire type CHRYSLER PACIFICA 2020 Vehicle Warranty

Fuel
Economy
Underinflated
tires
will
increase
tire
rolling
resistance
resulting
in
higher

fuel
consumption.
Tread
Wear
Improper
cold
tire
inflation
pressures
can
cause
abnormal
wear
patterns

and
reduced
tread
life,
resulting
in
the
need
for
earlier
tire
replacement.
Ride
Comfort
And
Vehicle
Stability
Proper
tire
inflation
contributes
to
a
comfortable
ride.
Overinflation

produces
a
jarring
and
uncomfortable
ride.
TireInflation Pressures
The
proper
cold
tire
inflation
pressure
is
listed
on
the
driver’s
side

B-Pillar
or
rear
edge
of
the
driver’s
side
door.
At
least
once
a
month:
• Check

and
adjust
tire
pressure
with
a
good
quality
pocket-type
pressure
gauge.
Do
not
make
a
visual
judgement
when
determining
proper
inflation.
Tires
may
look
properly
inflated
even
when
they
are
underinflated.
• Inspect tires for signs of

tire wear or visible damage.
CAUTION!
After inspecting or adjusting the tire pressure, always reinstall the
valve stem cap. This will prevent moisture and dirt from entering the
valve stem, which could damage the valve stem.
Inflation pressures specified on the placard are always “cold tire inflation
pressure”. Cold tire inflation pressure is defined as the tire pressure after
the vehicle has not been driven for at least three hours, or driven less than
1 mile (1.6 km) after sitting for a minimum of three hours. The cold tire
inflation pressure must not exceed the maximum inflation pressure
molded into the tire sidewall.
Check tire pressures more often if subject to a wide range of outdoor
temperatures, as tire pressures vary with temperature changes.
Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air
temperature change. Keep this in mind when checking tire pressure
inside a garage, especially in the Winter.
TIRES
13

Example:
If
garage
temperature
=
68°F
(20°C)
and
the
outside
tempera-
ture
=
32°F
(0°C)
then
the
cold
tire
inflation
pressure
should
be
increased

by
3
psi
(21
kPa),
which
equals
1
psi
(7
kPa)
for
every
12°F
(7°C)
for
this

outside
temperature
condition.
Ti re
pressure
may
increase
from
2
to
6
psi
(13
to
40
kPa)
during
operation.

DO
NOT
reduce
this
normal
pressur

e
build
up
or
your
tire
pressure
will

be
too
low.
Tire Pressures For High Speed Operation
The
manufacturer
advocates
driving
at
safe
speeds
and
within
posted

speed
limits.
Where
speed
limits
or
conditions
are
such
that
the
vehicle

can
be
driven
at
high
speeds,
maintaining
correct
tire
inflation
pressure
is

very
important.
Increased
tire
pressure
and
reduced
vehicle
loading
may

be
required
for
high
speed
vehicle
operation.
Refer
to
an
authorized
tire

dealer
or
original
equipment
vehicle
dealer
for
recommended
safe

operating
speeds,
loading


and
cold
tire
inflation
pressures.
WARNING!
High speed driving with your vehicle under maximum load is
dangerous. The added strain on your tires could cause them to fail.
You could have a serious collision. Do not drive a vehicle loaded to
the maximum capacity at continuous speeds above 75 mph
(120 km/h).
Radial Ply Tires
WARNING!
Combining radial ply tires with other types of tires on your vehicle
will cause your vehicle to handle poorly. The instability could cause
a collision. Always use radial ply tires in sets of four. Never combine
them with other types of tires.
TIRES
14

TireTy p e s
All Season Tires —IfEquipped
All
œeason
tires
provide
traction
for
all
seasons
(Spring,
Summer,
"VUVNO,

and
Winter).
Traction
levels
may
vary
between
different
all
season

tires.
All
season
tires
can
be
identified
by
the
M+S,
M&S,
M/S
or
MS

designation
on
the
tire
sidewall.
Use
all
season
tires
only
in
sets
of
four;

failure
to
do
so
may
adversely
affect
the
safety
and
handling
of
your

vehicle.
Summer Or Three Season Tires —IfEquipped
Summer
tires
provide
traction
in
both
wet
and
dry
conditions,
and
are

not
intended
to
be
driven
in
snow
or
on
ice.
If
your
vehicle
is
equipped

with
Summer
tires,
be
aware
these
tires
are
not
designed
for
Winter
or

cold
driving
conditions.
Install
inter
tires
on
your
vehicle

when
ambient
temperatures
are
less
than
40°F
(5°C)
or
if
roads
are

covered
with
ice
or
snow.
For
more
information,
contact


an
authorized

dealer.
Summer
tires
do
not
contain
the
all
season
designation
or
mountain/
snowflake
symbol
on
the
tire
sidewall.
Use
ummer
tires
only
in
sets

of
four;
failure
to
do
so
may
adversely
affect
the
safety
and
handling
of

your
vehicle.
WARNING!
Do
not
use
ummer
tires
in
snow/ice
conditions.
Yo u
could

lose
vehicle
control,
resulting
in
severe
injury
or
death.
Driving
too

fast
for
conditions
also
creates
the
possibility
of
loss
of
vehicle

control.
Snow Tires
Some
areas
of
the
country
require
the
use
of
snow
tires
during
the
inter.

Snow
tires
can
be
identified
by
a
“mountain/snowflake”
symbol
on
the

tire
sidewall.
If you need snow tires, select tires equivalent in size
and type to the original equipment tires. Use snow
tires only in sets of four; failure to do so may adversely
affect the safety and handling of your vehicle.
Snow tires generally have lower speed ratings than
what was originally equipped with your vehicle and
should not be operated at sustained speeds over 75 mph (120 km/h). For
speeds above 75 mph (120 km/h) refer to original equipment or an
TIRES
19

authorized
tire
dealer
for
recommended
safe
operating
speeds,
loading

and
cold
tire
inflation
pressures.
While
studded
tires
improve
performance
on
ice,
skid
and
traction

capability
on
wet
or
dry
surfaces
may
be
poorer
than
that
of
non-studded

tires.
Some
states
prohibit
studded
tires;
therefore,
local
laws
should
be

checked
before
using
these
tire
types.
Spare Tires—IfEquipped
NOTE:

For
vehicles
equipped
with
Tire
Service
Kit
instead
of
a
spare
tire,
please

refer
to
“Tire
Service
Kit”
in
“In
Case
Of
Emergency”
in
your

Owner ’s
Manual
for
further
information.
CAUTION!
Because of the reduced ground clearance, do not take your vehicle
through an automatic car wash with a compact or limited use
temporary spare installed. Damage to the vehicle may result.
TIRES
SpareTireMatching Original Equipped Tire And Wheel —If
Equipped
Your
vehicle
may
be
equipped
with
a
spare
tire
and
wheel
equivalent
in

look
and
function
to
the
original
equipment
tire
and
wheel
found
on
the

front
or
rear
axle
of
your
vehicle.
This
spare
tire
may
be
used
in
the
tire

rotation
for
your
vehicle.
If
your
vehicle
has
this
option,
refer
to
an

authorized
tire
dealer
for
the
recommended
tire
rotation
pattern.
Compact Spare Tire—IfEquipped
The
compact
spare
is
for
temporary
emergency
use
only.
Yo u
can
identify

if
your
vehicle
is
equipped
with
a
compact
spare
by
looking
at
the
spare

tire
description
on
the
Tire
and
Loading
Information
Placard
located
on

the
driver ’s
side
#QJMMBS

UIF
SFBS
FEHF
PG
UIF
ESJWFST
TJEF
EPPS
or
on
the

sidewall
of
the
tire.
Compact
spare
tire
descriptions
begin
with
the

letter
“T”
or
“S”
preceding
the
size
designation.
Example:
T145/80D18

103M.
T,
S
=
Temporary
Spare
Tire
Since
this
tire


has
limited
tread
life,
the
original
equipment
tire
should
be

repaired
(or
replaced)
and
reinstalled
on
your
vehicle
at
the
first

opportunity.
Do
not
install
a
wheel
cover
or
attempt
to
mount
a
conventional
tire
on

the
compact
spare
wheel,
since
the
wheel
is
designed
specifically
for
the
20

DRIVING ON ANY TIRE THAT DOES NOT HAVE THE CORRECT
INFLATION PRESSURE IS DANGEROUS
Any underinflated tire builds up excessive heat that may result in sudden
tire destruction. If tires are supplied as original equipment, refer to the
tire decal on the vehicle (check vehicle and/or vehicle owner ’s manual
for decal location) for the recommended operating pressures. For replace-
ment tires, the correct inflation pressure will be provided by your tire
retailer; if not, refer to the vehicle decal.
These inflation pressures must be maintained as a minimum. However,
do not exceed the maximum pressure rating indicated on the tire
sidewall.
CHECK THE COLD INFLATION PRESSURES IN ALL YOUR TIRES,
INCLUDING THE SPARE, AT LEAST ONCE EACH MONTH
Failure to maintain correct inflation may result in improper vehicle
handling and may cause rapid and irregular tire wear, sudden tire
destruction, loss of vehicle control and serious personal injury. Therefore,
inflation pressures should be checked at least once each month and
always prior to long distance trips. This applies to all tires, including
sealant types, and Self-Supporting tires which are as susceptible to losing
air pressure as any other type of tire if not properly maintained.
UNDERINFLATION
It is impossible to determine whether tires are properly inflated by
simply looking at them. It is almost impossible to “feel or hear” when a
tire is being run underinflated or nearly flat. Tires must be checked
monthly with a tire pressure gauge.
Pressures should be checked when tires are cold, in other words, before
they have been driven on. Driving, even for a short distance, causes tires
to heat up and air pressure to increase.
Checking pressure when tires are hot:
If pressures are checked after tires have been driven for more than three
minutes or more than one mile, (1.6 km) the tires become hot and the
pressures will increase by approximately 4 psi. Therefore when the tire
pressure is adjusted under these conditions, it should be increased to a
gauge reading of 4 psi greater than the recommended cold inflation
pressure.
BFGOODRICH TIRES
31

TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
speedometer. Excessive speed in a free-running, unloaded tire can cause
it to “explode” from centrifugal force. The energy released by such an
explosion is sufficient to cause serious physical injury or death. Never
allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not engage
in excessive wheel spin. Accelerating the motor excessively, particularly
with automatic transmission vehicles, may cause a drive tire that has lost
traction to spin beyond its speed capability. This is also true when
balancing a drive tire/wheel assembly on the vehicle using the vehicle
engine to spin the tire/wheel assembly.
HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important.However, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover, driving
at high speed reduces the reaction time available to avoid accidents and
bring your vehicle to a safe stop.
If you see any damage to a tire or wheel, replace it with the spare at
once and visit a participating BFGoodrich Tire Retailer.
Exceeding the maximum speeds shown on the following page for each
type of BFGoodrich tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire destruction
and rapid air loss. Failure to control a vehicle when one or more tires
experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
BFGOODRICH TIRES
33

The maximum load rating of your tires is molded on the tire sidewall. Do
not exceed this rating. Follow the loading instructions of the manufac-
turer of your vehicle and this will ensure that your tires are not
overloaded. Tires which are loaded beyond their maximum allowable
loads for the particular application will build up excessive heat that may
result in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any BFGoodrich® tire
retailer for advice concerning the correct size tire and pressures. Tire size
and pressures will depend upon the type and size of trailer and hitch
utilized, but in no case must the maximum cold inflation pressure or tire
load rating be exceeded. Check the tire decal and the owner ’s manual
supplied by the manufacturer of your vehicle for further recommenda-
tions on trailer towing.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR
SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES CHECK
HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH
MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect excessive
vibration, your vehicle may be out of alignment or balance. These
conditions not only shorten the life of your tires but adversely affect the
handling characteristics of your vehicle, which could be dangerous. If
you detect irregular wear or vibration, have your alignment and balance
checked immediately. Tires which have been run underinflated will show
more wear on the shoulders than in the center of the tread.
TIRE MIXING
BFGoodrich® tires are radial tires and for best performance it is recom-
mended that the same size and type of tire be used on all four wheel
positions. Before mixing tires of different types in any configuration on
any vehicle, be sure to check the vehicle manufacturer ’s Owner‘s Manual
for its recommendations.
It is especially important to check the vehicle manufacturer ’s owner ’s
manual when mixing, matching or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
BFGOODRICH TIRES
37

BFGOODRICH TIRES
FULL-SIZESPARE
Full-size
spare
tires
(not
temporary
spares)
of
the
same
size
and
construc-
tion
should
be
used
in
a
five
(5)
tire
rotation.
Always
check
the
inflation

pressure
of
the
full-size
spare
immediately
before
incorporating
it
into

rotation.
Follow
the
vehicle
manufacturer ’s
recommended
pattern
for

rotation,
or
if
not
available,
see
a
qualified
tire
technician.
REPLACEMENT
OF
TWO
(2)


TIRES
It
is
recommended
that
all
four
(4)
tires
are
replaced
at
the
same
time.

However,
whenever
only
two
tires
are
replaced,
the
new
ones
should
be

put
on
the
rear.
The
new
tires,
with
deeper
tread,
may
provide
better
grip

and
water
evacuation
in
wet
driving
conditions.
CUSTOMIZATION OF TIRES, WHEELS, ORSUSPENSION ON
SUVS ANDLIGHT TRUCKS
Due
to
their
size,
weight
and
higher
center
of
gravity,
vehicles
such
as

SUVs
and
light
trucks
do
not
have
the
same
handling
characteristics
as

automobiles.
Because
of
these
differing
characteristics,
failure
to
operate

your
SUV/truck
in
a
proper
and
safe
manner
can
increase
the
likelihood

of
vehicle
rollover.
Modifications
to
your
SUV/truck
tire
size,
tir
e
type,

wheels
or
suspension
can
change
its
handling
characteristics
and
further

increase
the
likelihood
of
vehicle
rollover.
Whether
your
SUV/truck
has

the
original
equipment
configuration
for
tires,
wheels
and
suspension
or

whether
any
of
these
items
have
been
modified,
always
drive
safely,

avoid
sudden,
sharp
turns
or
lane
changes
and
obey
all
traffic
laws.

Failure
to


do
so
may
result
in
loss
of
vehicle
control
leading
to
an
accident

and
serious
injury
or
death.
TIRE
ALTERATIONS
Do
not
make
or
allow
to
be
made
any
alterations
on
your
tires.

Alterations
may
prevent
proper
performance,
leading
to
tire
damage

which
can
result
in
an
accident.
Tires
which
become
unserviceable
due
to

alterations
such
as
truing,
whitewall
inlays,
addition
of
balancing
or

sealant
liquids,
or
the
use
of
tire
dressing
containing
petr

oleum
distillates

are
excluded
from
warranty
coverage.
39

REPAIRS - WHEREVER POSSIBLE, SEE YOUR BFGOODRICH®
TIRE RETAILER AT ONCE
If any BFGoodrich® tire sustains a puncture, have the tire demounted
and thoroughly inspected by any BFGoodrich® tire retailer for possible
damage that may have occurred.
A tread area puncture in any BFGoodrich® passenger or light truck tire
can be repaired provided that the puncture hole is not more than 1/4” in
diameter, not more than one radial cable per casing ply is damaged, and
the tire has not been damaged further by the puncturing object or by
running underinflated. Tire punctures consistent with these guidelines
can be repaired by following the Rubber Manufacturers Association
(RMA) recommended repair procedures.
TIRE REPAIRS
Repairs of all tires must be of the combined plug and inside patch type.
Plug only repairs are improper.A tire should be removed from the rim
and inspected prior to repair. Any tire repair done without removing the
tire from the rim is improper. An improperly repaired tire will cause
further damage to the tire by either leaking air or allowing air, moisture
and contaminants to enter the structure of the tire. An improperly
repaired tire can fail suddenly at a later date.
Never repair a tire with less than 2/32 nds of an inch tread remaining. At
this tread depth, the tire is worn out and must be replaced.
TEMPORARY SPARE TIRES
When using any temporary spare tire, be sure to follow the vehicle
manufacturer ’s instructions.
READING THE DOT
DOT XXXX XXXX XXX (prior to August 2000)
DOT XXXX XXXX XXX (1990-1999)
DOT XXXX XXXX XXXX (after July 2000)
THE DOT
The “DOT” symbol certifies tire manufacturer ’s compliance with U.S.
Department of Transportation tire safety standards. Next to the symbol is
the tire identification or “serial number”. The first two characters identify
the plant where the tire was manufactured. The next two characters
BFGOODRICH TIRES
40

reflect the tire size. The following one to four digits may be used at the
tire manufacturer ’s option as a descriptive code. The last three characters
are numbers identifying the week and year of manufacture. (Example:
“O25” means second week of the year of decade, eg.: 1995, 1985, etc.)
Tires produced after July 2000 have an additional digit to identify a given
decade. For example, 2800 means the tire was produced during the 28th
week of 2000; 0201 during the 2nd week of 2001. If the last digits of your
DOT number contain three numeric characters consult a qualified tire
technician to determine the year and decade of manufacture.
STORAGE
Tires contain waxes and emollients to protect their outer surfaces from
ozone and weather checking. As the tire rolls and flexes, the waxes and
emollients continually migrate to the surface, replenishing this protection
throughout the normal use of the tire. Consequently, when tires sit
outdoors, unused for long periods of time (a month or more) their
surfaces become dry and more susceptible to ozone and weather check-
ing and the casing becomes susceptible to flat spotting.
For this reason, tires should always be stored in a cool, dry, clean,
indoor environment. If storage is for one month or more, eliminate the
weight from the tires by raising the vehicle or by removing the tires
from the vehicle. Failure to store tires in accordance with these
instructions could result in damage to your tires or premature aging of
the tires and sudden tire failure.
When tires are stored, be sure they are placed away from sources of heat
and ozone such as hot pipes and electric generators. Be sure that surfaces
on which tires are stored are clean and free from grease, gasoline or other
substances which could deteriorate the rubber.(Tires exposed to these
materials during storage or driving could be subject to sudden failure.)
FOLLOW THESE MOUNTING RECOMMENDATIONS
Tire changing can be dangerous and must be done by professionally
trained persons using proper tools and procedures as specified by the
Rubber Manufacturers Association (RMA).
Your tires should be mounted on wheels of correct size and type and
which are in good, clean condition. Wheels that are bent, chipped, rusted
(steel wheels) or corroded (alloy wheels) may cause tire damage. The
inside of the tire must be free from foreign material. Have your retailer
check the wheels before mounting new tires. Mismatched tires and rims
BFGOODRICH TIRES
41