remote control CHRYSLER PACIFICA HYBRID 2017 2.G User Guide

NOTE:Be careful when moving the vehicle - ensure that
control of the vehicle is maintained. Also, ensure that
vehicle is secured to prevent unintentional movement
during and after moving the vehicle. If the external 12V
power becomes disconnected from the vehicle jump posts
or there is an interruption of the 12V power while moving
the vehicle, the vehicle’s transmission may engage Park.
When the vehicle is at the charging location, shift the
transmission back to Park, apply the electric park brake,
and start the high voltage battery charging. Once the
vehicle has been secured against unintentional movement
and high voltage battery charging has been initiated, the
jumper cables can be removed from the vehicle jump posts.
Jump-starting can be dangerous if done improperly so
please follow the procedures in this section carefully.
NOTE: When using a portable battery booster pack follow
the manufacturer ’s operating instructions and precautions.
WARNING!
Do not attempt jump-starting if the battery is frozen. It
could rupture or explode and cause personal injury.
CAUTION!
Do not use a portable battery booster pack or any other
booster source with a system voltage greater than 12
Volts or damage to the battery, starter motor, alternator
or electrical system may occur.
Preparations For Jump-Start
The remote battery posts in your vehicle is located on the
left side of the engine compartment.
418 IN CASE OF EMERGENCY

MULTIMEDIA
CONTENTS
UCONNECT RADIOS ....................495
 PERSONALIZED MENU BAR ...............495
 CYBERSECURITY ....................... .495
 UCONNECT SETTINGS ...................497
▫ Customer Programmable Features — Uconnect 8.4
Settings ............................. .497
 STEERING WHEEL AUDIO CONTROLS .......520
▫ Radio Operation ....................... .521
 AUX/USB/MP3 CONTROL ................521
 UCONNECT THEATER — IF EQUIPPED ......523
▫ Uconnect Theater Overview ...............523
▫ Getting Started ....................... .523
▫ Accessing The System From The Uconnect
Radio .............................. .524
▫ Uconnect Theater Controls ................525 ▫
Accessing The System From The Uconnect Theater
Rear Screens ......................... .526
▫ Pairing The Remote .....................527
▫ Unpairing The Remote ...................528
▫ Media Sources ........................ .528
▫ Uconnect Theater Remote Control ...........529
▫ Uconnect Theater Home Screen And Controls . . .530
▫ Play A DVD/Blu-ray Or USB Media File From
Uconnect System ...................... .532
▫ Blu-ray Controls – Disc Specific Functions .....534
▫ Uconnect Theater Apps ...................535
▫ Using The Rear Video USB Port .............537
▫ Play Video Games ..................... .538
▫ Headphones Operation .................. .538
▫ Disc

Menu ........................... .541
10

System Information
After pressing the “System Information” button on the
touchscreen, the following settings will be available:
Setting NameSelectable Options
System Information System Software Information Screen
NOTE:
When this feature is selected, a “System Information” screen will appear, displaying the system software version.
STEERING WHEEL AUDIO CONTROLS
The remote sound system controls are located on the rear
surface of the steering wheel at the three and nine o’clock
positions.
Steering Wheel Audio Controls (Back View Of Steering Wheel)
520 MULTIMEDIA

UCONNECT THEATER — IF EQUIPPED
Uconnect Theater Overview
Your Uconnect Theater is designed to give your family
years of enjoyment.
There are multiple ways to interact with your Uconnect
Theater system.
•Play your favorite CDs, DVDs or Blu-ray Discs
• Plug and play a variety of standard video games or
devices into the HDMI port
• Listen to audio over the wireless headphones
• Plug and play a variety of devices into the Video USB
port
• Plug in standard headphones to listen to audio
Please review this Owner’s Manual to become familiar
with its features and operation.
Getting Started
There are three different ways to operate the features of the
Uconnect Theater:
• The Remote Control
• The Uconnect Radio
• The Individual Uconnect Theater Touchscreens
Uconnect Theater Screen
1 — Uconnect Theater Touchscreen
2 — Uconnect Radio
3 — Uconnect Theater Media Hub10
MULTIMEDIA 523

Press this button and use the “Listen In” feature to listen to
audio through cabin speakers.
Accessing The System From The Uconnect
Theater Rear Screens
You can also access your Uconnect Theater system from the
rear screens from the steps below:
1. Lift screen upward, the system will automatically poweron.
NOTE: A message asking if you would like to pair a
remote will pop up if one has not already been paired to
the system.
2. If “YES” is selected to Pair a Remote, press any button on the remote and pairing will immediately start.
3. If “NO” is selected, the Uconnect Theater home screen will pop up. NOTE:
•
There will be a touchscreen notification message when
pairing is successful. Refer to “Pairing The Remote” on
the full procedure of how to pair the remotes.
• Test to make sure the remote is successfully paired by
dragging your finger across the gesture pad. If you do
not see the on screen arrow, try using the “Screen”
button to switch between screen one and screen two to
make sure the remote is controlling the intended screen.
It may take several seconds for the remote to react when
initially paired.
• If remote is ever non-operational, try performing the
pairing process again.
526 MULTIMEDIA

Pairing The Remote
If the remote needs to be paired to your Uconnect Theater
system, follow the procedure below:
1. Install batteries into both remotes.
2. Press and hold theScreen,” “Down,” and “Play/Pause
buttons on each remote control simultaneously until the
remote backlight flashes.
3. Press the Settings icon found in the lower left portion of the Uconnect Theater touchscreen. 4. Press the “Remote” button on the Uconnect Theater
touchscreen found in the settings menu.
5. Press the “Manage Remote Controls” button and con- firm that there are no remotes already paired to the
system.
6. Push the back arrow button on the Remote to go back to the remote menu.
7. Press the “Pair Remote” option. Press and hold down the “OK” button until pairing process is fully complete.
A touchscreen notification will appear indicating that
your remote has been paired successfully or unsuccess-
fully.
8. Test to see if the remote is paired to the intended screen by running your finger on the gesture pad to see if the
cursor responds.
NOTE:
• If remote is ever non-operational, try pairing remote.
• The system can accommodate up to 10 paired remote
controls.
Remote Pairing
10
MULTIMEDIA 527

Unpairing The Remote
In events such as updating the Uconnect Theater software,
or taking a remote to another vehicle, the remote will need
to be unpaired from your Uconnect Theater system. To
unpair the remote, follow the procedure below:
1. Select “Manage Remote Controls” from the Remotesection of Settings” and follow the on screen instruc-
tions to complete the unpairing process.
2. Push and hold the “Screen”, “Down Arrow”, and “Play/Pause” buttons for 5 seconds, or until the remote
screen indicator light flashes.
3. Once complete, the remote will be ready to pair again.
NOTE: There will be a touchscreen notification message
when unpairing is successful. Repeat the above steps to
unpair a second remote.
Media Sources
Media Sources
1 – Available Sources Screen 1
2 – USB Source Playing Screen 2
528 MULTIMEDIA

Users can select content for each screen from the radio by
choosing desired content from drop down menu.
NOTE:Use the “View Screen” function to pull content
from one screen to the other in a single press of a button.
Doing this however will disable and gray out certain
player controls on the screen viewing the other screen’s
content.
Uconnect Theater Remote Control
1. Gesture Pad — Control mouse pointer position in this
area to move and select items on the touchscreen,
functions similar to a mouse.
2. Mute Button — Mutes headphone audio.
3. Home Button — Push to access “Sources”.
4. Arrow Buttons — Push the arrow
buttons
to highlight an item or scroll through menus.
5. Fast Forward Button— Push and hold to fast
forward through the current audio track or video
chapter. Push once to skip to the next track.
6. Play/Pause Button— Begin/resume or pause
disc play.
7. Fast Rewind Button— Push and hold to fast
rewind through the current audio track or video
chapter. Push once to revert back to the previous
track.
8. OK Button — Push to select the highlighted option in a
menu.
9. Screen Selector Button — Push the screen selector to
toggle between screen 1 (Driver Side), or screen 2
(Passenger Side).
Remote Control
10
MULTIMEDIA 529

10.Back Button — Push to exit out of menus or return to
previous screen.
11 . Power Button — Turns the screen and wireless head-
phone transmitter for the selected Channel on or off.
12. Screen Indicator — Indicates which screen (1 or 2) is
being controlled by the remote control when a button is
pushed.
Replacing The Remote Control Batteries
Each remote control requires two AAA batteries for opera-
tion.
To replace the batteries:
1. Locate the battery compartment on the back of the remote, then slide the battery cover downward.
2. Remove the old batteries and follow battery recycling procedures for your area.
3. Install new batteries, making sure to orient them accord- ing to the polarity diagram shown inside the battery
compartment.
4. Replace the battery compartment cover.
Uconnect Theater Home Screen And Controls
Uconnect Theater Home Screen
1 — Search Button (Media
Search)
2 — Power Button
3 — Settings Button
4 — Toggle Button List and Icon
Vi e w5 — Source Card Page Indicator
6 — Wired Headphone Volume
7 — Climate Control Button
8 — Home Button
9 — Source Cards
530 MULTIMEDIA

You can choose sources such as HDMI, USB, Apps, or
Blu-ray. You may also view content of the opposite screen
in one step by choosing the “View Screen” source card.
NOTE:
•Source card order can be changed by pressing the
Settings button on the touchscreen and scrolling down
to Source Card Order.
• Use the “View Screen” function to pull content from one
screen to the other. Doing this however will disable and
gray out certain player controls. General Settings
To change source card order, select “Source Card Reorder”,
then press and hold source card on the touchscreen, and
drag and drop in desired order.
You can also adjust the following below and more.
•
Brightness
• Media port lighting on and off
• Clock on and off
NOTE: System information can also be displayed under
General Settings.
Remote Settings
Under this setting, you can access the following:
• Manage Remotes
• Pair Remote
• Remote sensitivity (This adjusts the speed and sensi-
tivity of cursor on screen when using gesture pad)
Source Card Selection
10
MULTIMEDIA 531