CHRYSLER SEBRING CONVERTIBLE 2008 3.G Owners Manual

BULB REPLACEMENT
Low Beam Headlight, High Beam Headlight
1. Open the hood.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the totally integrated power
module aside prior to replacing the low beam headlight
on the driver's side of the vehicle.
2. Rotate the applicable bulb and connector assembly
1¤4
turn counterclockwise and remove the assembly from the
headlight housing.
3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
1 Ð High Beam Headlight
2 Ð Low Beam HeadlightMAINTAINING YOUR VEHICLE 4017

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the
headlight housing and rotate it
1¤4turn clockwise to lock
it in place.
Front Turn Signal/Park Light
1. Open the hood.
2. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the headlight housing.
Front Turn Signal/Park Light
402 MAINTAINING YOUR VEHICLE

3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
headlight housing and rotate the connector
1¤4turn clock-
wise to lock it in place.
Front Fog Light
NOTE:Access to the lights through the lower fascia
cutout is limited. We recommend you access the lights by
turning the steering wheel to allow access and remove
the inner fender shield.
1. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the fog light housing.Front Fog Light
MAINTAINING YOUR VEHICLE 403
7

2. Remove the bulb from the connector socket and install
the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
3. Install the bulb and connector assembly into the fog
light housing and rotate the connector
1¤4turn clockwise
to lock it in place.
Tail/Stop Light, Rear Turn Signal Light, Backup
Light
The taillights are a two-piece design. The tail/stop lights
and rear turn signal lights are located in the rear corner
body panels. The backup lights and rear fog lights are
located in the trunk lid.
Changing the Tail/Stop Light or Rear Turn Signal
Light
1. Open the trunk.
404 MAINTAINING YOUR VEHICLE

2. Remove the two plastic wing nuts from the taillight
housing.
3. Grasp the taillight housing with one hand on the
bottom of the housing and the other hand on the inboard
housing flange and pull it outward firmly to disengage
the housing from the vehicle.4. Rotate the applicable bulb's electrical connector1¤4
turn counterclockwise and remove it from the taillight
housing.
Location Plastic Wing Nuts
1 Ð Tail/Stop Light
2 Ð Turn Signal LightMAINTAINING YOUR VEHICLE 405
7

5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
taillight housing and rotate the connector
1¤4turn clock-
wise to lock it in place.
7. Reinstall the taillight housing.
Changing the Backup Light
1. Open the trunk.
2. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the housing.
3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
housing and rotate the connector
1¤4turn clockwise to
lock it in place.
Backup and Rear Fog Light
406 MAINTAINING YOUR VEHICLE

License Plate Light
1. Remove the two retaining screws from the lens.2. Gently pry the lens loose.
3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the lens and the two retaining screws.
Location and Removal of Rear License Light Lens
MAINTAINING YOUR VEHICLE 407
7

Center High-Mounted Stop Light (CHMSL)
1. Open the trunk lid.
2. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the CHMSL housing.3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
4. Install the bulb and connector assembly into the
CHMSL housing and rotate the connector1¤4turn clock-
wise to lock it in place.
High-mounted Stop Light Bulb Replacement
408 MAINTAINING YOUR VEHICLE

FLUIDS AND CAPACITIES
EngineU.S. Metric
Fuel (approximate)
All Engines 16.9 gallons 64 liters
Engine Oil with Filter
2.4L Engine (SAE 5W-20, API Certified) 4.5 quarts 4.26 liters
2.7L Engine (SAE 5W-20, API Certified) 5.5 quarts 5.2 liters
3.5L Engine (SAE 10W-30, API Certified) 5.5 quarts 5.2 liters
Cooling System *
2.4L Engine (MopartAntifreeze/Coolant 5 Year/100,000 Mile For-
mula) or equivalent.7.7 quarts. 7.3 liters
2.7L Engine (MopartAntifreeze/Coolant 5 Year/100,000 Mile For-
mula) or equivalent.9.8 quarts. 9.3 liters
3.5L Engine (MopartAntifreeze/Coolant 5 Year/100,000 Mile For-
mula) or equivalent.11.6 quarts. 11.0 liters
* Includes heater and coolant recovery bottle filled to MAX level.
MAINTAINING YOUR VEHICLE 409
7

FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
Component Fluids, Lubricants, and Genuine Parts
Engine CoolantMopartAntifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid
Organic Additive Technology) or equivalent
Engine Oil (2.4L & 2.7L)Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the en-
gine oil fill cap for the correct SAE grade meeting DaimlerChrysler Mate-
rial Standard MS-6395.
Engine Oil (3.5L)Use API Certified engine oil. SAE 10W-30 is recommended. Refer to the
engine oil viscosity chart for the correct SAE grade meeting
DaimlerChrysler Material Standard MS-6395.
Oil Filter (2.4L) Mopart04884900AB or equivalent.
Oil Filter (2.7L & 3.5L) Mopart04884899AB or equivalent.
410 MAINTAINING YOUR VEHICLE