load capacity CHRYSLER VOYAGER 2020 Vehicle Warranty

DOT Symbol and Tire Identification Number:The “DOT” symbol
constitutes a certification that the tire conforms to applicable U.S.
Department of Transportation motor vehicle safety standards (for tires).
Following the “DOT” symbol is the tire identification number, also
known as the DOT serial number or code. For example:
(a) DOT Symbol (d) Tire Manufacturer ’s Code
(b) Manufacture Plant Code (e) Week of Production (01-52)
(c) Tire Size Code (f) Year of Production (last two digits
of year)
BRIDGESTONE® - FIRESTONE®
* For
tires
produced
from
2000-on.
In
the
example
above,
the
tire
was
produced
in
the
18th
week
of
2000.
For
tires
produced
prior
to
2000,
there
is
one
digit
in
group
(f)
which
identifies
the
last
digit
of
the
year
of
production,
i.e.
“329”
would
likely
signify
the
32nd
week
of
1999,
but
could
possibly
signify
the
32nd
week
of
1989.
If
in
doubt,
consult
a
qualified
tire
service
professional.
The
DOT


symbol
and
tire
identification
number
can
be
found
on
at
least

one
sidewall
near
the
wheel.
The
other
sidewall
may
have
a
partial
serial

code
that
excludes
(e)
and
(f)
above.
Maximum
Load
and
Inflation:
The
maximum
load
and
maximum

inflation
pressure
is
marked
on


each
sidewall
in
metric
and
English
units.

For
example:
MAX
LOAD
685
kg
(1,510
lbs)
AT
240
kPa
(35
psi)
MAX
PRESS
NOTE:

The
load
and
inflation
values
marked
on
the
tire
sidewall
are

maximum
permissible
values
for
the
tire
only.
Never
assume
that
these

values


are
the
actual
maximum
load
capacity
or
recommended
tire

pressure
values
for
your
vehicle.
See
“Tire
Inflation
Pressure,”
“Tips
for

Safe
Tire
Inflation,”
and
“Tips
for
Safe
Loading”
in
this
manual.
78

This Limited Warranty applies only to consumers actually using the tire
in the United States and Canada. For warranty conditions outside the
United States and Canada, see your local Bridgestone Firestone distribu-
tor.
Obligations under this policy may not be enlarged or altered by anyone.
In accordance with Federal Law, this Limited Warranty has been desig-
nated as aLimited Warranty.” Nothing in this Limited Warranty is
intended to be a representation that tire failures cannot occur. This
Limited Warranty is given in the United States by Bridgestone Firestone
North American Tire, LLC, 535 Marriott Dr., Nashville, TN 37214 and in
Canada by Bridgestone Firestone Canada Inc., 5770 Hurontario St., Suite
400, Mississauga, Ontario, Canada L5R 3G5.
OWNER’S OBLIGATIONS
In order to keep this Limited Warranty valid, we require you to have your
tires regularly inspected and rotated per the recommendations outlined
in the sections of this manual entitled Tire Damage, Inspection and
Service Life” and “Radial Tire Rotation” and to furnish proof of same in
order to receive an adjustment. Such proof should show the date,
mileage, and servicing location. A sales receipt containing this informa-
tion will suffice. In addition, a “Maintenance Record” is included on the
back cover of this manual. It is your obligation to maintain proper tire
inflation pressures as specified by the vehicle manufacturer and to
operate the vehicle within tire/vehicle load capacity and speed limita-
tions. It is also your obligation to maintain proper wheel alignment and
tire/wheel assembly balance. To request an adjustment, you must present
the tire to an authorized Bridgestone Firestone retailer. Complete and
sign the customer section of the Bridgestone Firestone North American
Tire, LLC Limited Warranty adjustment form and pay appropriate
replacement price, taxes, disposal fee, and service charges, if any.
ARBITRATION
You and Bridgestone Firestone North American Tire, LLC agree that all
claims, disputes, and controversies between you and it, including any of
its agents, employees, successors, or assigns, arising out of or in connec-
tion with this Limited Warranty, or any other warranties, express or
implied, including a failure of warranty and the validity of this arbitra-
tion clause, but excluding claims for personal injury or property damage,
shall be resolved by binding arbitration between you and it, according to
the formal dispute resolution procedures of the National Arbitration
BRIDGESTONE® - FIRESTONE®
84

•EXPLOSION OF TIRE/RIM ASSEMBLY DUE TO IMPROPER
MOUNTING. Only specially trained persons should mount tires.
• FAILURE TO MOUNT RADIAL TIRES ON APPROVED RIMS.
• FAILURE TO DEFLATE SINGLE OR DUAL ASSEMBLIES COM-
PLETELY BEFORE DEMOUNTING.
• TIRE SPINNING. On slippery surfaces such as snow, mud, ice, etc.,
do not spin tires in excess of 35 mph (55 kph), as indicated on the
speedometer.
• EXCESSIVE WHEEL SPINNING. This can also result in tire disinte-
gration or axle failure.
WARNING!
Vehicle handling, traction, ride comfort and other performance
parameters may be significantly affected by a change in tire size or
type. Before replacing tires, always consult and follow the vehicle
owner ’s manual because some vehicle manufacturers prohibit
changing tire size. When selecting tires that are different from the
original equipment size make certain:
1. The tires have adequate load-carrying capacity based on the vehicle placard,
2. The tires have sufficient inflation pressure to carry the load and
3. There is proper clearance with no interference points between the tire and vehicle.
The consumer must be aware to always drive safely and obey all
traffic laws. Avoid sudden, sharp turns or aggressive lane changes.
Failure to follow any of these warnings may result in loss of control
of the vehicle, leading to an accident and serious injury or death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and performance
from your Goodyear or Dunlop tires is to give them a simple but frequent
(at least monthly) inspection for proper inflation, even tread wear and the
presence of any damage.
DO MAINTAIN PROPER INFLATION PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire performance,
safety and fuel economy. Check inflation pressures at least once a month
and before long trips. Use an accurate tire pressure gauge. Always check
GOODYEAR DUNLOP TIRES
128

pressures when the tires are cold (when the vehicle has been driven less
than one mile). If you must check inflation when the tires are hot, add
4 psi (27 kPa) to the recommended cold inflation pressure. It is difficult
to tell just by looking at radial tires whether they are underinflated.*
Furthermore, when operating a vehicle equipped with radial tires, it is
difficult to notice when a tire has gone flat or nearly flat since the “feel”
of the vehicle does not change significantly.
*Evidence of air loss or repeated underinflation always requires expert
inspection to determine the source of leakage and tire removal to
determine repairability.To avoid injury, NEVER attempt to reinflate a
tire that has been run severely underinflated. Progressive air loss may
result from punctures, cuts, curbing, impacts or partial bead unseating.
Some fitment causes for air loss are (1) incomplete bead seating, (2) bead
tearing caused by a machine tool due to insufficient lubrication or
improper adjustment. Leaking valve core or rubber valve components
should be replaced when problems are detected and whenever tires are
replaced.
Always maintain inflation pressure at the level recommended by the
vehicle manufacturer as shown on the vehicle placard, vehicle certifi-
cation label or in the vehicle owner ’s manual:
Under inflation is the leading cause of tire failure and may result in
severe cracking, component separation or “blowout.” It reduces tire load
capacity, allows excessive sidewall flexing and increases rolling resis-
tance, resulting in heat and mechanical damage. Maintaining proper
inflation pressure is the single most important thing you can do to
promote tire durability and maximize tread life.
Over inflation increases stiffness, which may deteriorate ride and gener-
ate unwanted vibration. Over inflation also increases the chances of
impact damage.
DON’T OVERLOAD YOUR VEHICLE
Check your vehicle owner ’s manual to determine the load limits.
Overloading your vehicle places stress on your tires and other critical
vehicle components. Overloading a vehicle can cause poor handling or
increased fuel consumption and may cause tire failure. Overloading your
tires can result in severe cracking, component separation or “blowout.”
Never fit your vehicle with new tires that have less load capacity than
shown on the vehicle tire placard and remember that optimum rim width
GOODYEAR DUNLOP TIRES
129

GOODYEARDUNLOPTIRES
is
important
for
proper
tire
load
distribution
and
function.
The
maximum

load
capacity
stamped
on
the
sidewalls
of
P-Metric
&
European
Metric

tires
is
reduced
by
10%
when
used
on
a
light
truck,
utility
vehicle
or

trailer.
Never
fit
P-Metric
or
European
Metric
tires
to
light
trucks
that

specify
LT-type
replacement
tires.
DON’TSPINYOUR TIRES EXCESSIVELY
Avoid
excessive
tire
spinning
when
your
vehicle
is
stuck
in
snow,
ice,

mud
or
sand.
The
centrifugal
forces
generated
by
a
free-spinning

tire/wheel
assembly
may
cause
sudden
tire
explosion,
resulting
in

vehicle
damage
and/or
serious
personal
injury
to
you
or
a
bystander.

Never
exceed
35
mph
/
55
kph,
as
indicated
on
your
speedometer.
Use
a

gentle
backwar

d
and
forward
rocking
motion
to
free
your
vehicle
for

continued
driving.
Never
stand
near
or
behind
a
tire
spinning
at
high

speeds,
for
example,
while
attempting
to
push
a
vehicle
that
is
stuck
or

when
an
on-the-car
spin
balance
machine
is
in
use.
DO CHECK YOUR TIRES FORWEAR
Always
remove
tires
from
service
when
they
reach
two
thirty-seconds
of

an
inch
(2/32)
remaining
tread
depth.
All
new
tires
have
tread
wear

indicators
which
appear
as
smooth
banks
in
the
tread
grooves
when
they

wear
to
the
two
thirty
seconds
of
an
inch
(2/32)
level.
Many
wet
weather

accidents
result
from
skidding
on


bald
or
nearly
bald
tires.
Excessively

worn
tires
are
also
more
susceptible
to
penetrations.
DO CHECK YOUR TIRES FORDAMAGE
Frequent
(at
least
monthly)
inspection
of
your
tires
for
signs
of
damage

and
their
general
condition
is
important
for
safety.
If
you
have
any

questions,
have
your
tire
Dealer
inspect
them.
Impacts,
penetrations,

cracks,
knots,
bulges
or
air
loss
always
require
tire
removal
and
expert

inspection.
Never
perform
a
temporary
repair
or
use
an
inner
tube
as
a

substitute
for
a
proper
repair.


Only
qualified
persons
should
repair
tires.
PROPER TIREREPAIR
NOTE:

Goodyear
does
not
warrant
any
inspection
or
repair
process.
The

repair
is
entirely
the
responsibility
of
the
repairer
and
should
be

made
in
accordance
with
established
Rubber
Manufacturers
Association

(RMA)
procedures.
130

DON’T MIX TIRES OF DIFFERENT SIZES AND TYPES ON THE
SAME AXLE
For optimum handling and control, Goodyear recommends fitment of
four (4) tires of the same type and size unless otherwise specified by the
vehicle manufacturer.
WARNING!
Before you replace your tires, always consult the vehicle owner ’s
manual and follow the vehicle manufacturer ’s replacement tire
recommendations. Vehicle handling may be significantly affected
by a change in tire size or type. When selecting tires that are
different from the Original Equipment size, see a professional
installer in order to make certain that proper clearance, load-
carrying capacity and inflation pressure are selected. Never exceed
the maximum load capacity and inflation pressure listed on the
sidewall of the tire. Always drive safely and obey all traffic laws.
Avoid sudden, sharp turns or aggressive lane changes. Failure to
follow this warning may result in loss of control of the vehicle,
leading to an accident and serious injury or death.
When replacing tires, you must maintain the outside diameter and
load-carrying capacity of the Original Equipment tire. Inflation pressure
may need to be adjusted to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or JATMA standards
for correct load and inflation information.
NEVER FIT TIRES TO A VEHICLE THAT HAVE LESS LOAD-
CARRYING CAPACITY THAN REQUIRED BY THE ORIGINAL
EQUIPMENT MANUFACTURER
Examples: Many vehicles, such as large passenger vans, require Load
Range E tires as designated by the vehicle manufacturer. Fitment of a tire,
such as a Load Range D, with less carrying capacity is not allowed. In
other cases, tires of the same size may carry different load indexes in the
service description. You must make certain the replacement tires fitted to
the vehicle have a load-carrying capacity equal to or greater than what
the Original Equipment manufacturer specifies.
GOODYEAR DUNLOP TIRES
132

HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important.However, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover, driving
at high speed reduces the reaction time available to avoid accidents and
bring your vehicle to a safe stop. If you see any damage to a tire or
wheel, replace it with the spare at once and visit a participating
Michelin Tire Retailer.
Exceeding the maximum speeds shown on the following page for each
type of MICHELIN® tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire destruction
and rapid air loss. Failure to control a vehicle when one or more tires
experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
SPEED RATINGS
Speed Symbols are shown on the sidewall of some MICHELIN® tires.
The following table shows the maximum speed corresponding to the
symbol.
*Some V (or VR) rated tires may have a speed capacity greater than
149 mph (240 km/h). Consult your participating Michelin® tire retailer
for maximum speed rating if your vehicle capability exceeds this speed.
**Z (or ZR) rated tires are designed to use on cars with maximum speed
capabilities in excess of 149 mph (240 km/h).
(W and Y speed ratings are subcategories of Z).
Consult your Michelin tire retailer for maximum speed capabilities. For
PAX® System Tires consult an authorized PAX System Tire Retailer.
Although a tire may be speed-rated, we do not endorse the operation of
any vehicle in an unsafe or unlawful manner. Speed ratings are based on
laboratory tests which relate to performance on the road, but are not
applicable if tires are underinflated, overloaded, worn out, damaged,
altered, improperly repaired or retreaded.
MICHELIN
172

ROADSIDE ASSISTANCE
Patterns sold after May 1st 2014 by NEXEN TIRE in the United States and
Canada are eligible for a free 24/7/365 Roadside Assistance for a period
of 36 months from the purchase date. Upon purchasing Nexen tires, the
consumer will receive an activation card from the tire shop. An online
registration needs to be completed in order to have access to a toll free
phone number to call in case of a flat tire. A qualified professional will
change your flat tire with your spare tire free of charge. If a working spare
is not available, towing will be provided free of charge to the nearest
NEXEN TIRE dealer or authorized place of repair.
*Nexen Tire reserves the right to change the terms and conditions of all
warranties at any time.
TIRE CARE AND MAINTENANCE GUIDE
Tire failure can result in serious damage and/or personal injury. To
reduce the risk of tire failure we recommend the following:
•Maintain proper inflation pressure and do not use at under inflation or
over inflation. Pressure should be set at the level recommended by
vehicle manufacturer.
• Wheel alignment and balancing should be checked at regular intervals.
• Do not overload. The maximum load carrying capacity is molded on
the sidewall of the tire.
• Do not spin your tires excessively and avoid driving over curbs,
potholes, obstacles and edges of pavement.
• Never drive on smooth (bald) tires. By law, tires must be replaced
when 2/32 of tread depth remained, as indicated by tread wear
indicator molded in the tread grooves.
• Check your tires frequently for any scrapes, cuts, foreign objects,
separations or bulges. If damage is found, do not attempt to dismount
a tire yourself. Change damaged tire with the spare and contact your
local authorized NEXEN TIRE dealer immediately.
• Do not drive in excess of speed limits allowed by law or the maximum
speed justified by driving conditions.
• To achieve proper even wear and gain maximum tread life, tire
rotation at regular intervals is required.
NEXEN TIRE
191

Tire Size:A combination of alphabetic and numeric characters that
indicate the nominal dimensions of a tire:
Load Index: a numerical code indicating the maximum load carrying
capacity of a tire at the maximum cold inflation pressure.
LOAD MAXIMUM LOAD PER TIRELOAD MAXIMUM LOAD PER
TIRE
INDEX Kg Lbs INDEX Kg Lbs
80 450 992 106 950 2094
81 462 1018 107 975 2149
82 475 1047 108 1000 2205
83 487 1074 109 1030 2271
84 500 1102 110 1060 2337
85 515 1135 111 1090 2403
86 530 1168 112 1120 2469
87 545 1201 113 1150 2535
88 560 1234 114 1180 2601
89 580 1278 115 1215 2679
90 600 1323 116 1250 2756
91 615 1356 117 1285 2833
92 630 1389 118 1320 2910
93 650 1433 119 1360 2998
94 670 1477 120 1400 3087
95 690 1521 121 1450 3197
96 710 1565 122 1500 3307
97 730 1609 123 1550 3417
98 750 1653 124 1600 3528
99 775 1708 125 1650 3638
100 808 1764 126 1700 3748
101 825 1819 127 1750 3859
102 850 1874 128 1800 3969
103 875 1919 129 1850 4079
104 900 1984 130 1900 4190
105 925 2039 131 1950 4300
PIRELLI TIRES
206

8. Tire Replacement
The tires fitted to your vehicle as original equipment were tested and
approved by the vehicle manufacturer and the tire manufacturer and take
into account all aspects of the vehicle’s operation. Changes in the tire size,
type or construction should not be made without seeking advice from the
vehicle or tire manufacturer or an authorized Pirelli dealer since unap-
proved tires on your vehicle could adversely affect steering, handling,
braking and traction. The tire information (tire size, load index and speed
symbol) as found on the vehicle placard or in the owner ’s manual should
always be followed when replacing tires.
It is strongly recommended that Pirelli tires be mounted in sets of four
with the same tread type. Pirelli tires should not be mixed with other tire
brands. It is necessary to follow this procedure because different tire
constructions have different handling characteristics. Tires on the same
axle must be the same manufacturer, brand, tire size, load index, speed
rating and Pirelli part number.
When changing only two tires on a vehicle which is homogeneously
fitted (four tires of the same tire size), fit the new tires on the rear axle.
This applies to all vehicles regardless of their drive axle. (Front or Rear
Drive).
On all wheel drive or four wheel drive vehicles the tires must always be
replaced in sets of four.
When replacing tires on light truck vehicles, you should always follow
the vehicle manufacturer ’s recommendations. Passenger and light truck
tires are not interchangeable, due to differences in their pressures and
load carrying capacity.
P-Metric and Euro-metric Interchangeability: Euro-metric (Example: 225/
45R17) tires have a load index which is equal to or greater than that of the
same size P-metric (Example: P225/45R17) tire. Therefore, they have the
same or higher load carrying capacity at the maximum rated inflation
pressure. Always check with your tire dealer or Pirelli Tire Consumer
Affairs to be sure of the exact interchangeability to maintain proper
vehicle dynamics.
Please be aware that it is important that, before fitting the suggested tires,
the fitment is allowed by the technical specifications of the vehicle, the
vehicle manufacturer and the relevant homologations. Pirelli Tire does
not express any view as to the compatibility of the wheel/tire combina-
tion with the technical specifications for the chassis and vehicle.
PIRELLI TIRES
211