ignition Citroen BERLINGO 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
NOTE:The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch. Automatic gearbox ECU.
Electrical harnesses.
Battery voltage.
Remove:
The gear lever knob
(1)(pull upwards).
The cover (2)(Unclip).
The top of the central console (3).
Unlock the «shift lock» (4)with the aid of a screwdriver.
Move the gear selection lever out of position «P».
Engine: KFV
C3
C5FP0ETCB2CP3GZC

Downloaded from www.Manualslib.com manuals search engine 346
CLUTCH
GEARBOX
TRANSMISSION
XSARAAL4 AUTOMATIC GEARBOX
Engines: NFU RFN RHZ
SHIFT LOCK.
NOTE:
The «shift lock»«P».
U
nlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed. Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch.
Automatic gearbox ECU.
Electrical harnesses. Battery voltage.
Remove:
The cover
(1).
Unlock the «shift lock» (2) with the aid of a screwdriver.
Move the gear selection lever out of position «P».
C5FP06ZC
C5FP06YC

Downloaded from www.Manualslib.com manuals search engine 347
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
SHIFT LOCK.
NOTE:
The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).
NOTE:It is impossible to unlock the «shift lock»
«Shift lock»
«shift lock»by pressing at «a»with a screwdriver placed in the gear selection
control gate.
Move the gear selection lever out of position
«P».
Engine: RFN
XSARA PICASSO
B2CP3N8C

Downloaded from www.Manualslib.com manuals search engine 480
ELECTRICAL
SYSTEM
CHARGING CIRCUIT ALTERNATOR WITH MONOFUNCTION REGULATOR
Checking the alternator output.
Connect as shown in the diagram opposite, using an ammeter (A), a voltmeter (V),
and a rheostat
(R)or a Volt/Ammeter/Rheostat combination.
Referring to the vehicle’s equipment specification
(see table opposite), adjust the
engine speed and rheostat charge to obtain
U = 13.5 V.
Reminder:The excitation energising current will flow through the warning lamp;
check that the warning lamp comes on when the ignition is switched on. It shouldgo out when the engine has started
(accelerate slightly).
Checking the voltage regulator.
Set the rheostat to zero and disconnect all the electrical consumers.
Display
3000alternator rpm. If U alternator is > 14.7 V, the regulator is faulty.
Note:These tests should be performed with the engine hot and the battery fully
charged.
Method of reading the alternator speed.
Fit a reflecting shim on the pulley of the alternator.
Adjust a stroboscope to the frequency equivalent to the control speed.
(e.g. 2000 rpm = 2000/60 = 83 Hz).
Adjust the engine speed so that the shim appears fixed.
D1AP025C
A: Ammeter.B:Battery.G: Generator.L: Warning lamp.K1and K2:Switch.R: Electric charge.S:Shunt 200mV/200A.V:Voltmeter.1 : Alternator.