belt Citroen BERLINGO 2004 1.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine 186
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1EP18GC
Setting the timing.
Remove the upper timing cover (1).
Rotate the engine by means of the crankshaft screw (2).
NOTE:The pegging hole is located under the crankshaft bearing cap cover.
Peg the engine flywheel, using tool
[3].
Remove the lower timing cover (3).
Uncouple the exhaust line from the manifold.
IMPERATIVE: Uncouple the exhaust line in order to avoid damaging the front flexible pipe. Twisting,
pulling and bending the front flexible pipe reduces its life.
Remove:
The engine speed sensor (6).
The belt retaining stop (5).
The screw (2).
The crankshaft pinion (4)(with its magnetic track «a»).
IMPERATIVE: The magnetic track should show no signs of damage and should not be approached
by any other source of magnetism.Should this not be adhered to,it is essential to replace the crank
shaft pinion.
Refit the screw (2).
B1BP2LXC
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 188
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1EP18HC
Setting the timing (continued).
Hold the tensioner roller, using a hexagonal spanner at «b».
Slacken the screw (9).
Remove the timing belt (10).
Refitting.
IMPERATIVE: Check that both the tensioner roller and the fixed roller turn freely
(no tight spots). If this is not the case, replace the rollers.
Fitting of the pulle
ys.
Camshaft pulley: Tighten to 4,3 ± 0,4 m.daN.
Fuel high pressure pump pulley: Tighten to 5 ± 0,5 m.daN.
The crankshaft pinion is located without a screw at the end of the crankshaft.
Fitting of the rollers.
IMPERATIVE: Check that the tensioner roller turns freely (no tight spot).Otherwise, replace the rollers.
Guide roller:Tighten to 4,5 ± 0,4 m.daN.
Tensioner roller :Pretighten to 0,1 m.daN.
Check the condition of the seals at the camshaft and at the crankshaft pinion.
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine ENGINE
189
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1EP18JD
Setting the timing (continued).
NOTE:
Screw (9)slackened.
Position the timing belt
(10)observing the following sequence:
Crankshaft pinion
(4).
Guide roller
(12).
Camshaft pulley
(11)(check that the belt is held correctly against the roller).
Coolant pump pinion
(13).
Fuel high pressure pump pulley
(15).
Tensioner roller
(14).
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 190
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1EP18KC
Setting the timing (continued).
Turn the tensioner roller to the right to bring the index «c»to position «d», using a
hexagonal spanner.
Tighten the screw
(9)of the tensioner roller, tighten to 3 ± 0,3 m.daN.
Remove the tools [4]and [5].
Rotate the engine
ten times(check that the timing pinion is correctly up against the
crankshaft).
Check:
The pegging of the camshaft.
The crankshaft pinion.
The fuel high pressure pump pinion
(15).
The correct positioning of the index of the dynamic tensioner.
If these are not correct, repeat the operation to position the timing belt.Refit:
The engine speed sensor
(6).
The belt retaining stop (5), tighten to 0,7 m.daN.
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1EP18LCB1BP2LZC
Setting the timing (continued).
Refit:
The intermediate RH engine support, tighten the screws
(16)to 5,5 ± 0,5 m.daN.
The RH engine support, tighten the screws
(17)to 4,5 ± 0,4 m.daN.
The bottom timing cover
(3).
Immobilise the engine flywheel, using tool
[3].
Remove the screw
(2).
Refit the accessories drive pulley and tighten to:
Pretighten to
: 3 ± 0,3 m.daN.
Angular tighten to
:180° ± 1,8°.
Remove tool
[3].
Refit:
The top cover
(1).
The accessories belt
(see corresponding operation).
The exhaust line
(see corresponding operation).
The front RH splashshield. The front RH wheel.
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1BP2N0C
Tools.
[1]
Engine flywheel peg Ø 12 mm : ().0194C
[2]
Camshaft pulley peg Ø 8 mm : ().0194B
[3]
Crankshaft pulley peg Ø 5 mm : ().0194A
Preliminar
y operations.
Remove:
The front RH wheel.
The front RH splashshield.
The accessories belt
(see corresponding operation).
Uncouple:
The supply unions
(1).
The air/air heat exchanger inlet/outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connector
(2).
Support the engine by means of a roller jack equipped with a chock.
Remove the engine supports
(4) and(5).
C3

Downloaded from www.Manualslib.com manuals search engine 194
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18YD
Checks (continued).
Refit the screw (8).
Rotate the crankshaft six times
(clockwise).
IMPERATIVE: Never rotate the engine backwards.
Peg:
The camshaft, using tool
[2](oil the pegs).
The fuel high pressure pump pulley (14), using tool [3]at «c».
WARNING:The magnetic track should show no signs of damage and should not be
approached by any source of magnetism.
Peg the crankshaft at
«b», using tool [3].
IMPERATIVE:Should it be impossible to peg the camshaft, check that the
offset between the hole in the camshaft pinion and the pegging hole is not
greater than 1 mm.Otherwise repeat the operation to position the timing belt
(see corresponding
operation)
.
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
195
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18ZC
Checks (continued).
NOTE:
The index «e»of the dynamic tensioner roller should be centred within the area «d».
Check the correct positioning of the index
«e».
If it is not correct, repeat the operation to tension the timing belt
(see corresponding operation).
Refitting.
Refit the tool [1]at «a».
Remove the screw
(8).
Refit:
The upper timing cover
(11).
The lower timing cover
(10).
The accessories drive pulley
(9).
The screw
(8).
Tightening torque.
Screw (8):
Pretighten to
:3 ±0,3 m.daN.
Angular tightening
:180° ± 5°.
Remove the tool
[1].
C3

Downloaded from www.Manualslib.com manuals search engine 196
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1BP2N0C
Checks (continued).
Refit:
The engine support (7), tighten to 1,5 ± 0,4 m.daN.
The engine support
(4), tighten to 6,1 ± 0,6 m.daN.
The engine support
(5), tighten to 6 ± 0,6 m.daN.
The electrical harness
(6).
Couple:
The exhaust line, tighten the collar to : 2,5 ± 0,3 m daN.
The fuel supply unions
(1).
The air/air heat exchanger inlet/outlet pipes
(3).
Connect the connector
(2).
Refit:
The accessories belt (see corresponding operation).
The front RH splashshield
(see corresponding operation).
The front RH road wheel, tighten to
9 ±1 m.daN.
Reconnect the battery.
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
197
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18VD
Setting the timing.
Perform the preliminary operations for checking the timing up to removing tool [1]at «a»for immobiling the
engine flywheel.
Refit screw
(8).
Rotate the crankshaft to bring the camshaft towards its pegging point.
Peg the camshaft, using tool
[2](oil the pegs).
WARNING: Do not press or damage the track which is the target for the engine speed sensor (14).
Peg the crankshaft at «b», using tool [3].
Remove:
The timing protector
(13).
The engine speed sensor
(14).
Slacken the screw
(12)of the tensioner roller, keeping it slack with the aid of a hexagonal spanner at
«c».
Detension the belt by pivoting the tensioner roller
(clockwise).
Remove the timing belt, commencing with the coolant pump pinion.
Peg the pulley
(15), using a 5 mmdiameter peg at «d».
C3