steering Citroen BERLINGO MULTISPACE RHD 2015 2.G Owner's Guide

 117
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Good practice
Sit in a normal upright position.
W ear   a   correctly   adjusted   seat   belt.
d

o not leave anything between the
occupants and the airbags (a child,
pet,
  object...).  
This
  could   hinder   the  
operation

  of   the   airbags   or   injure   the  
occupants.
a

fter an accident or if the vehicle has
been
  stolen   or   broken   into,   have   the  
airbag

  systems   checked.
All
  work   on   the   airbag   system   is   strictly  
forbidden unless it is carried out by
qualified

  personnel   at   a   CITROËN  
dealer

  or   a   qualified   workshop.
Even if all of the precautions
mentioned
  are   observed,   a   risk   of  
injury

  or   of   minor   burns   to   the   head,  
chest

  or   arms   when   an   airbag   is  
deployed

  cannot   be   ruled   out.   In   fact,  
the

  bag   inflates   almost   instantly   (within  
a

  few   milliseconds)   then   deflates   within  
the

  same   time   discharging   the   hot   gas  
via

  openings   provided   for   this   purpose.Lateral airbags
Only
  put   recommended   covers   on  
the

  seats.  
These
  will   not   hinder  
inflation

  of   the   lateral   airbags.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
Do

  not   fix   or   attach   anything   to   the   seat  
backs.

 
This
  could   cause   injury   to   the  
chest

  or   arms   when   the   lateral   airbag  
inflates.
d

o not sit with the upper part of the
body any nearer to the door than
necessary.
Front airbags
d

o not drive holding the steering wheel
by
  its   spokes   or   resting   your   hands   on  
the

  centre   part   of   the   wheel.
d

o not allow passengers to place
their
  feet   on   the   dashboard,   they   risk  
serious

  injury   if   the   airbag   is   deployed.
Smoke
  as   little   as   possible   as  
deployment

  of   the   airbags   can   cause  
burns

  or   the   risk   of   injury   from   a  
cigarette

  or   pipe.
Never
  remove   or   pierce   the   steering  
wheel

  or   hit   it   violently.
Airbags only operate when the
ignition is switched on.
This
 
equipment
 
only
 
operates
 
once.
 
If

 
a
 
second
 
impact
 
occurs
 
(during
 
the
 
same

 
or
 
a
 
subsequent
 
accident),
 
the
 
airbag

 
will
 
not
 
operate.
The
 
deployment

 
of

 
an

 
airbag

 
or

 
airbags

 
is

 
accompanied
 
by
 
a
 
slight
 
discharge
 
of

 
smoke
 
and
 
a
 
noise,
 
due
 
to
 
the
 
activation of the pyrotechnic cartridge
incorporated

 
in
 
the
 
system.
This
 
smoke
 
is
 
not
 
harmful,
 
but
 
sensitive

 
individuals
 
may
 
experience
 
some

 
irritation.
The
 
noise
 
of
 
the
 
detonation
 
may
 
result
 
in a slight loss of hearing for a short
time. The

 
passenger's
 
front
 
airbag
 
must
 
be deactivated if a child seat is
installed

 
facing
 
rearward.
Chapter 5, "Children on board"
section.
airbags
SaFETY
5

 119
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Front airbags
The front airbags are fitted in the centre of the steering wheel for the
driver and in the dashboard for the
front  passenger.
d

eployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front
  impact   applied   to   all   or   part   of   the  
front

  impact   zone   A in the longitudinal
centreline of the vehicle on a horizontal
plane
  directed   from   the   front   towards  
the

  rear   of   the   vehicle.
The
  front   airbag   inflates   between   the  
front occupant of the vehicle and the
dashboard to cushion their forward
movement.
d
eactivationo
nly the passenger's front airbag can
be   deactivated:
-

with the ignition switched off
,
insert
  the   key   into   the   passenger's  
front airbag deactivation switch,
-


turn it to the of
f "OFF" position,
-
 
then
  remove   the   key,   keeping   the  
switch

  in   the   new   position.
The passenger's front
airbag
  warning   lamp   in   the  
instrument

  panel   is   on   while  
the

  airbag   is   deactivated.If
  the   two   airbag   warning   lamps  
are on continuously

, do not install
a rear-facing child seat, contact
a
  CITROËN   dealer   or   a   qualified  
workshop.
Front airbag fault
T
o ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rear-facing child seat on the
front
  passenger   seat.   Otherwise,   the  
child

 
would
 
risk
 
being
 
kille
d  
or
 
seriously
 
injured

  if   the   airbag   were   to   inflate.
r
eactivation
In the "OFF" position, the passenger's
front airbag will not be deployed in the
event   of   an   impact.
As   soon   as   the   child   seat   is   removed,  
turn the airbag switch to the

"O n "
position to re-activate the passenger's
front airbag and so ensure the safety
of your passenger in the event of an
impact.
If   this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, contact a
CITR

o Ë n dealer or a
qualified
  workshop   to   have  
the

  system   checked.
airbags
SaFETY
5

Berlingo_2_VP_en_Chap06_Accessoire_ed02-2014
 137
OtHEr AccESSOrIES
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
vehicle. 
A 
wide   range   of   recommended  
accessories and genuine parts is
available.
a further range is also available,
structured

  around   comfort,   leisure   and  
maintenance:
Anti-theft

  alarm,   window   etching,   first  
aid

  kit,   high   visibility   vest,   front   and  
rear

  parking   sensors,   warning   triangle,  
security

  bolts   for   alloy   wheels,   ...
Seat
  covers   compatible   with   airbags  
for the front seats, bench seat, rubber
mats,

 
carpet
 
mats,
 
snow
 
chains,
 
blinds,
 
tailgate

  bicycle   carrier,   ...
To
  prevent   the   mat   from   becoming  
caught

  under   the   pedals:
-
 
ensure
  that   the   mat   and   its   fixings  
are positioned correctly

,
-
 
never
  fit   one   mat   on   top   of   another.Audio
  equipment,   hands-free   kit,
 speakers,
  CD   changer,   satellite navigation
 system,  USB  box,  V ideo  kit,  ...
Regardless
  of   the   audio   and   telematic
 equipment

  offered   on   the   market,   the
 technical constraints associated with


the
  fitting   of   equipment   of   these   product
 groups

  mean   that   the   special   features
 of

  the   equipment   and   its   compatibility
 with the capacities of your vehicle's


standard
  equipment   must   be   taken   into
 account.

  Please   ask   a   CITROËN   dealer
 for

  more   information   before   fitting   such
 equipment.
Maximum weights on bars
-


T
ransverse bars on longitudinal
bars:
  75   Kg   (these   bars   are   not  
compatible

  with   the   Modutop   roof).Installing radiocommunication
transmitters
You are advised to contact a CITR
o Ë n
dealer before installing accessory
radiocommunication
  transmitters   with  
external

  aerial   on   your   vehicle.
The
  CITROËN dealer   network  
will

  inform   you   of   the   specification  
(frequency

  band,   maximum   output  
power

,   aerial   position,   specific  
conditions of installation) of the
transmitters

  which   can   be   fitted,   in  
accordance with the Motor V

ehicle
Electromagnetic
  Compatibility  
Directive
  (2004/104/EC).
Front
  mud   flaps,   rear   mud   flaps,  
15/17 inch

  alloy   wheels,   wheelarch  
trim,

  leather   steering   wheel,   ...
Screenwash, interior and exterior
cleaning
  and   maintenance   products,  
spare

  bulbs,   ...
Equipment
AccESSOrIES
6

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
141
PEtrOL EnGInE
1. Screenwash  reservoir.
2.  
Fusebox.
3.

 
Engine
  coolant   header   tank.
Battery
  connections:
+
  Positive   terminal.
-
  Negative   point   (earth).
Take
  care   when   working   under   the   bonnet.
4.  Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.7.
 Engine   oil   filler   cap.
8.  
Power
  steering   fluid   reservoir.
Under the bonnet
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
142
dIESEL EnGInE
4. Brake  and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick. 7.
 Engine   oil   filler   cap.
8.  
Power
  steering   fluid   reservoir.
9.
 
Priming
  pump.
1.
 Screenwash
 
reservoir.
2.
 
Fusebox.
3.

 
Engine

 
coolant
 
header
 
tank.
Battery
  connections:
+
  Positive   terminal.
-
  Negative   point   (earth).
Take
 
care
 
when
 
working
 
under
 
the
 
bonnet.
Under the bonnet

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
144
cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
topping up
The

 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required

 
to
 
top
 
up
 
the
 
level,
 
have
 
the
 
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your safety , we would advise that you use
products
  of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
diesel additive level
( d iesel with particle
emission filter)
topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
emission
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
159
The temporary tyre repair kit consists of  a   compressor   and   a   bottle  
(containing

  a   sealant).
using the kit
1. Tick  the   deflated   wheel   on   the  speed
  limitation   sticker   then   affix  
the

  sticker   to   the   vehicle's   steering  
wheel

  to   remind   you   that   a   wheel   is  
in

  temporary   use.
2.

Clip the bottle
1 on the
compressor 2.
3.

Connect the bottle
1 to the valve of
the
  tyre   to   be   repaired.
4.
 
T
ake   care   to   unwind   the  
compressor

  pipe   before   connecting  
it

  to   the   bottle.
5.

Connect the power lead to one of
the

  vehicle's   12V   sockets.
6.
 
Switch
  on   the   compressor   by  
pressing button

A until the tyre
pressure
  reaches   2.0   bars.   If   this  
pressure cannot be reached, the
tyre

  cannot   be   repaired.
7.
 
Remove
  and   store   the   compressor.
8.
 
Drive
  immediately,   for   a   few   miles  
(kilometres),

  at   reduced   speed,  
to
  fill   the   puncture.
9.
 
Adjust
  the   pressure   using   the  
compressor

  in   accordance   with   the  
recommendation

 
for
 
the
 
vehicle
 
and
 
check

  that   the   leak   is   filled   correctly  
(no

  further   loss   of   pressure).
10.
 
Drive
  at   reduced   speed   (50 mph  
[80

  km/h]).  
The
  tyre   must   be  
examined

  and   repaired   by   a  
specialist

  as   soon   as   possible.
a
fter use, the bottle can be stored in
a   plastic   bag,   supplied   in   the   kit,   to  avoid staining your vehicle with traces
of
  fluid.
Warning:
  the   bottle   of   gel   contains  
ethylene-glycol, a product which
is

  harmful   if   swallowed   and   which  
causes

  irritation   to   the   eyes.
Keep
  it   out   of   reach   of   children.
a

fter use, do not discard the bottle into
the
  environment,   take   it   to   a   CITROËN  
dealer or to an specialised waste
disposal

  site.
Replacement
  bottles   of   sealant   are  
available

  from   CITROËN   dealers.
PuncturE rEPAIr KIt
The kit is located in one of the two storage  compartments   located   under  
the

  front   seats.
Vehicles
  supplied   with   a   temporary  
puncture

  repair   kit   do   not   have   a   spare  
wheel

  or   tooling   (jack,   wheelbrace,   ...).
Changing a wheel
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
176
FuSES undEr tHE BOnnEt
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
9 10Headlamp
  beam   motor,   parc   management   unit
10 30 Engine
  components
11 40 Spare
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
Changing a fuse

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
178
Without lifting (4 wheels on the
road)
You should always use a towing bar.
BEInG tOWEd
Ths procedure involves the use of the
towing eye supplied with the tools for
changing
  a   wheel.
From the front
- Unclip the cover by pressing the
bottom  part.
-
 
Fully
  screw   in   the   removable   towing  
eye.
From the rear
- Unclip the cover using a coin or the
flat  part   of   the   towing   eye.
-
 
Fully
  screw   in   the   removable   towing  
eye. When towing with the engine
switched

  off,   there   is   no   braking   or  
steering

  assistance.
Lifting (only 2 wheels on the
road)
It is preferable to raise the vehicle
using
  professional   lifting   equipment.
Vehicles fitted with a manual
gearbox (d iesel version)
In the case of vehicles fitted with a  manual   gearbox,   the   gear   lever  
must

  be   in   neutral,   failure   to   observe  
this

  special   condition   may   result   in  
damage

  to   transmission   and   braking  
components

  and   the   absence   of  
braking

  assistance   when   the   engine   is  
started

  again.
Chapter
 
9,
 
"Changing
 
a
 
wheel"
 
section.
Having your vehicle towed

10.3
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
The system is protected in such a way that it will only operate  in   your   vehicle.
eMyWay
01 First steps - c ontrol panel
For safety reasons, the driver must carry out operations which
  require   prolonged   attention   while   the   vehicle   is  
stationary

.
When the engine is switched off and to prevent
discharging
  of   the   battery,   the   system   switches   off  
following

  the   activation   of   the   energy   economy   mode.
cOntEntS
02
Steering mounted
controls
03

General operation
04

n avigation - Guidance
05
t
raffic information
06

u sing the telephone
07
r adio
08

Music media players
09


Audio
settings
10
c onfiguration
11
t
rip
computer p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
10.4
10.6
10.7
10.9
10.22
10.25
10.35
10.38
10.44
10.45
10.47
Satellite navigation system
Multimedia audio system
Bluetooth
® telephone
12

Screen menu
map
Frequently asked questions p.
p.
10.48
10.52