engine Citroen BERLINGO MULTISPACE RHD 2017 2.G User Guide

34
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Front / lateral
airbag flashing
  or  
remaining

  on.a
  failure   of   an   airbag.Have
  the   system   checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop   without   delay.
Chapter
  5,   "Airbags"   section.
Front
passenger's
airbag
deactivated on. the intentional deactivation
of this airbag in the
presence of a rearward
facing
  child   seat.Chapter
  5,   "Airbags"   or   "child   safety"   section.
Low fuel
level on with gauge
needle in the
red
  zone.When
  it   first   comes   on,  
there remains around
8 litres

  of   fuel   in   the   tank.  
The distance you can drive
on this fuel depends on
your style of driving and the
engine

  type.You
  must   fill   up   with   fuel   to   avoid   running   out.
This warning lamp comes on each time you
switch
  on   the   ignition   until   you   have   filled   up.
Capacity
  of   the   tank:   approximately   60   litres   (or  
55

  litres   according   to   version).
Never
  risk   driving   until   the   tank   is   empty,   this  
could

  damage   the   emissions   and   injection  
systems.
flashing. cutting of

f of the fuel supply
following
  a   serious   impact.Restore
  the   supply.
Chapter
  7,   "Fuel"   section.
EOBD
emission
control
system flashing
  or  
remaining

  on.a
  failure   of   the   system.There
  is   a   risk   of   damage   to   the   catalytic  
converter

.   Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Battery
charge on.
a fault in the charging
circuit. Check
  the   battery   terminals,   …
Chapter
  8,   "Battery"   section.
flashing. placing of the active
functions on standby
(economy
  mode).Chapter
  8,   "Battery"   section.
remaining on,
in spite of the
checks. an
  ignition   or   injection  
malfunction.Have

  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.

+ +
39
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
SCR emissions control system
Alerts InformationSolution - action
The UREA, Service and diagnostic warning lamps
come on, an SCR emissions control system fault
has
  been   detected. This is is temporary fault, the alert disappears as
soon as the exhaust emissions return to normal
levels.
After 30 miles (50 km) without AdBlue
®
Confirmation of the fault which is not related to a lack   of   fluid. The
  remaining   driving   range   700   miles  
(1   100   km).
Go   to   a   CITROËN   dealer   or   a   qualified   workshop  
as

  soon   as   possible   to   avoid   a   breakdown.
The
  fault   is   confirmed.
The next time the ignition is switched on, the
authorised driving range will be displayed in miles
(kilometres)
  and   the   alert   will   be   repeated   every  
30
  seconds.
The limit of the driving range has been reached,
exhaust
  emissions   levels   are   above   the   limits.
Starting
  is   impossible. To restart the engine, you must contact a
CITROËN
  dealer   or   a   qualified   workshop.
- BlueHDi Diesel
READY TO GO
3

40
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
FUEL GAUGEC OOLANT TEMPERATURE
The needle is positioned before the
red zone:
  normal   operation.
In arduous conditions of use or hot
climatic conditions, the needle may
move
  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-
stop immediately
, switch off the
ignition.  
The
  fan   may   continue   to  
operate for a certain time, up to
approximately 10 minutes,
-

wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As the cooling system is pressurised,
follow the procedure below to avoid the
risk   of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   in   the   header   tank,
- if necessary , remove the cap to
top up.
If the needle remains in the red
zone,
  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The fuel level is tested each time the
key
 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the warning lamp comes on
continuously.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.

47
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
SERVICE INDICATOR
This programmes service intervals
according  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
A few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance recorder resumes normal
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few
seconds,   the   spanner   flashes   and   the   number   of miles/kilometres

  remaining   is   displayed:
A few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance recorder resumes normal
operation
  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A few moments after the ignition
has been switched on, the spanner
indicating a service operation comes
on; the display for the total distance
recorder
 
gives
 
(in
 
round
 
figures)
 
the
 
distance remaining before the next
service.
The points at which a service is due
are calculated from the last indicator
zero

 
reset.
The point at which a service is due is
determined
 
by
 
two
 
parameters:
-

the distance travelled,
-


the time which has elapsed since
the

 
last
 
service.
The distance remaining before the
next service may be weighted by
the time factor, depending on the
type
 
of
 
driving. With the engine running the spanner
remains on until the service has been
carried
  out.
For BlueHDi Diesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination of the Service warning
lamp,
  on   switching   on   the   ignition.
Each time the ignition is
switched on and for a few
seconds, the spanner
flashes
  and   the   excess  
distance

  is   displayed.
For BlueHDi Diesel versions, the
spanner can also come on early,
according the level of deterioration
of
  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
READY TO GO
3

48
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Trip recorder zero
reset button
After this operation, if you wish
to  disconnect   the   battery,   lock  
the

 
vehicle   and   wait   for   at   least   five  
minutes, otherwise the zero re-set will
not

 
be   registered.
Engine oil level indicator
Depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service warning lamp,
accompanied by an
audible signal and a message in the
screen, indicates a low oil level which
could
  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction of the
engine   oil   level   indicator.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.Dipstick
A = maximum, never exceed
this level as a surplus of oil
may
  damage   the   engine.
Contact a CITROËN dealer
or   a   qualified   workshop  
without

  delay.
B = minimum, top up the level
via   the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting reaches
the minimum


(or maximum) setting, release the
button then press it again to increase
(or
 
reduce)
 
the   brightness.
As soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.

51
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It is only possible to come out
of position N
  if   the   brake   pedal   is  
pressed.
The change from position

A (driving in
automatic mode) to position M (driving
in manual mode) or vice versa can be
made
  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector must be in position N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle is moving, do not select this
position

  even   momentarily.
READY TO GO
3
Gearbox and steering wheel

52
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes automatically to neutral N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed (for example when
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator completely during gear
changes.
-


A
gear change instruction is
accepted only if the engine speed
permits.
-

For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic mode, without any action on
your
 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

53
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode
  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The engine restarts automatically -
START mode - as soon as you want to
move
  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level
  when   stationary.
Operation
Going into engine STOP modeThe "ECO" warning lamp
comes on in the instrument
panel and the engine goes
into
  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

, at speeds below 5 mph
(8
  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a time counter calculates the sum of
the periods in ST

OP mode during a
journey.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox, for your comfort during
parking   manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking,   power   steering,   for   example.
Never refuel with the engine in
STOP mode; you must switch off
the   ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
READY TO GO
3
Stop & Start

54
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Going into engine START modeThe "ECO" warning lamp
goes
  off   and   the   engine   starts:
-

with a manual gearbox
, when you
fully depress the clutch pedal,
-

with a 6-speed electronic
gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position   N and
the
  brake   pedal   released,   when  
you move the gear lever to
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With a manual gearbox in STOP
mode, if a gear is engaged without
fully depressing the clutch pedal, a
warning lamp comes on or a message
is
  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.
Special cases: START invoked
automatically
For your safety and comfort, START is
invoked
  automatically   when:
-

you open the driver's door
,
-

you unfasten the driver's seat belt, In this case the

"ECO"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
This operation is perfectly normal.
Deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in
the passenger compartment, it may be
preferable
  to   deactivate   Stop   &   Start.
At any time, press the "ECO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp coming on accompanied by a
message

  in   the   screen.
If the system has been deactivated
in STOP mode, the engine restarts
immediately.
Reactivation
Press the "ECO OFF" switch again.
The system is active again; this is
confirmed
  by   the   switch   warning  
lamp going of

f and a message in the
instrument
  panel.
The system is reactivated
automatically at every new start
using
  the   key.
Operating fault
In the event of a malfunction
with the system, the "ECO
OFF" switch warning lamp
flashes,  then   comes   on  
continuously

.
This
  system   requires   a   specific  
battery

  with   a   special   specification  
and technology (reference
numbers available from a CITROËN
dealer

 
or
  a   qualified   workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
have
 
it
 
checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop.
In the event of a fault in STOP mode,
the
 
vehicle   may   stall.  
All
  of   the   warning  
lamps in the instrument panel come
on.

 
It
 
is
 
then   necessary   to   switch   off  
the ignition and start the engine again
using

 
the
  key.
-

the speed of the vehicle exceeds
15

 
mph
 
(25
 
km/h)
 
with
 
a
 
manual
 
gearbox

 
or
 
7
 
mph
 
(11
 
km/h)
 
with
 
the 6-speed electronic gearbox
system,
-
some special conditions (battery


charge,
 
engine
 
temperature,
 
braking
 assistance,

 
ambient
 
temperature...)
 where the engine is needed to


assure
 
control
 
of
 
a
 
system.
Stop & Start

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start