clock Citroen BERLINGO MULTISPACE RHD 2017 2.G Owner's Manual

181
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
CHANGING A BULB
Type A
All  glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
Type C
Halogen
  bulb:   release   the  
retaining spring from its
housing. T
ype B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
T

ypes of bulb
Various
 
types
  of   bulb   are   fitted   to   your  
vehicle.
T

o
 
remove
 
them:
Type D
Light-emitting diode
(LED):
  for   replacement  
of the daytime running
lamps, contact a
CITROËN dealer or a
qualified

  workshop.
QUICK HELP
8
Changing a bulb

183
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
3. Direction indicators
Type B, PY21W - 21W (amber)
-
Remove the cover by pullin
g the
flexible
  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-

Remove the bulb by pressing it
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4. Front foglamps
T

ype C, H1 - 55W
-

Remove the three clips and the
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-

Disconnect the bulb holder
connector by pressing the tab at
the

  top.-

Remove the bulb holder by
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-

Replace the module (bulb holder
and

  bulb).
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
QUICK HELP
8
Changing a bulb

185
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
After changing the rear direction
indicator bulb, the reinitialisation time is
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-

with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit

  towards   you.
For more information on bulbs, refer to
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B, PY21W - 21W (amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their
 
coating
 
and
 
seals. Chapter 9, "Changing a wheel"
section.
-

Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-

Holding the lamp, disconnect the
electrical

  connector.
QUICK HELP
8
Changing a bulb

186
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Number plate lamps
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
Third brake lamp
Type A, W16W - 16W
Type A, W5W - 5W
With tailgate
-

Disengage the plastic lens using a
screwdriver

.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it. With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-

Disconnect the connector by
moving

 
aside
 
its
 
tab.
-

T

urn the bulb holder a quarter turn
anticlockwise.
-
 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.
Changing a bulb