height CITROEN C CROSSER 2010 Owners Manual

II
!
C O M F O R T
48
FRONT SEATS
Forwards-backwards adjustment
Raise the control bar and slide the seat
forwards or backwards.
When your seat is at the correct dis-
tance, move it forwards and backwards
slightly without using the control bar to
check that it is secured correctly. Driver's seat cushion height and
angle adjustment
Pull and/or push the control several
times to adjust the height of the seat.
Seat back angle adjustment
Pull the control upwards to adjust the
seat back.
When the seat back is at the correct angle,
release the control.
Manual mode
To prevent the seat back from
moving forward sharply and
knocking you, press on it with
your back or push it with your hand
while operating the lever.

II
C O M F O R T
49
Electric mode (driver's seat only)
Forwards-backwards adjustment
Push the control forwards or rearwards to
move the seat to the position required. Driver's seat cushion height and
angle adjustment
Pull or push the front of the control to raise
or lower the front of the seat cushion.
Pull or push the rear of the control to raise
or lower the rear of the seat cushion.
Pull or push the entire control to raise or
lower the entire seat cushion. Seat back angle adjustment
Tilt the control forwards or rearwards to
straighten or tilt the seat back.
FRONT SEATS
To avoid discharging the battery, use
the electric mode with the engine
running.

II
!
C O M F O R T
50
Front armrest
You can move the console housing cover
in order to use it as an armrest.

With the engine running , tilt the button
to the position required.
The temperature of the seat is regulated
automatically.
There are two setting positions:
- "HI": High heating
- "LO": Low heating
When the button is in the intermediate
position, the heating is switched off.
The indicator lamps A come on when
the system is activated.
Heated seats adjustment
To raise the head restraint, pull it up-
wards.
To lower the head restraint, push it
downwards pressing the height adjust-
ment button at the same time.
To remove the head restraint, bring it to
the uppermost position then remove it
pressing the height adjustment button
at the same time.
To refi t the head restraint, engage the
stems of the head restraint in the holes
pressing the height adjustment button
at the same time.
Head restraint height adjustment
Never drive with the removed
head restraints in the vehicle as
they could be thrown around the
vehicle on sharp braking. They must
be in place and adjusted correctly.
After installing the head restraint,
check that the height adjustment but-
ton is locked correctly.
The adjustment is correct when the
top of the head restraint is aligned
with the top of the head of the seated
person.

II
!
C O M F O R T
60
REAR VIEW MIRROR
Adjust the mirror by moving it up or
down and/or to the left or right.
The rear view mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other, push
or pull the lever on the lower edge of
the mirror.
STEERING WHEEL MANUAL
HEIGHT ADJUSTMENT

 Pull the locking lever downwards
(position B ) while supporting the
steering wheel.

 Adjust the steering wheel to the re-
quired height.

 Lock the steering wheel adjustment
by pushing the lever upwards (posi-
tion A ). The sun visors fold forwards, and to the
side when they are unhooked.
They are fi tted with a courtesy mirror
and a ticket holder.
As a safety precaution, these op-
erations must only be carried out
while the vehicle is stationary.

VI
S A F E T Y
102
SEAT BELTS Height adjustment
Fastening

 Pull the strap, then insert the tongue
in the buckle A .

 Check that the seat belt is fastened
correctly by pulling the strap.
 to lower the attachment point, press
the control B and slide the fi xing C
down,

 to raise the attachment point, press
the control B and slide the fi xing C up.
Unfastening

 Press the red button on the buckle A .
Front seat belts
The front seat belts are fi tted with a pre-
tensioning and force limiting system.
This system improves safety in the front
seats in the event of a front or side im-
pact. Depending on the severity of the
impact, the pretensioning system in-
stantly tightens the seat belts against
the body of the occupants.
The pretensioning seat belts are active
when the ignition is on.
The force limiter reduces the pressure
of the seat belt on the chest of the oc-
cupant, so improving their protection.