reset Citroen C CROSSER 2012 1.G Owner's Manual

I
!
!
MONITORING
32 The total distance is
displayed in zone 1
of
the screen and the trip
distance in zone 2
.
DISTANCE RECORDERS (A/B)

System for measuring the total distance
travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear. When the engine is
running, this indicates
the temperature of the
coolant.
COOLANT TEMPERATURE
If the bar is close to the critical
position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

You must stop your vehicle as soon
as it is safe to do so.


Wait a few minutes before switching
off the engine.

Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running
, this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles/
kilometres travelled.
RANGE
When the range is less than 30 miles
(50 km)
, dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the
pressure to drop.
When the pressure has dropped,
remove the cap and top up the level, if
necessary.
Contact a CITROËN dealer or a
qualifi ed workshop. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current fuel consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the
battery, the previous fuel
consumption data is lost and the
value displayed will be different from
that displayed before the battery was
disconnected. The distance displayed
must be considered an approximate
indication.

I
MONITORING
33
SERVICE INDICATOR Resetting the service indicator to zero
Your CITROËN dealer or a qualifi ed
workshop carries out this operation
after each service.
If you have carried out your vehicle's
service yourself, the zero reset
procedure is the following:


)
switch off the ignition.

)
press the INFO
button several times
in succession until the service indi-
cator is displayed.

)
press and hold the INFO
button for
a few seconds until the spanner
fl ashes
.

)
press the INFO
button while the
spanner is fl ashing to change the dis-
play "---"
to "CLEAR"
then the time
remaining before the next service is
due is displayed.


Service overdue
O
peration
When the ignition is switched on, you
must press the INFO
button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
next service is due.
After a certain distance and a certain
time, the display of "---"
is reinitialised
and the display indicates the time
remaining before the next service is
due. System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:


- the distance travelled (in miles (km)),

- the time elapsed since the last ser-
vice (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user's driving habits.
Example:
the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--"
remains displayed
until the fi rst service of a new vehicle
has been carried out.

Example:
the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer or
a qualifi ed workshop. Each time the ignition is switched on,
the display "PERIODIC INSPECTION"

is displayed for a few seconds to
indicate that the service must be carried
out without delay.

I
MONITORING
34
TRIP COMPUTER Average fuel consumption (l/100 km or km/l or mpg)
This is the average fuel
consumption since the
last zero reset.
This fi gure may change following
a change in the style of driving or
the relief resulting in an increase
or decrease in the current fuel
consumption.


Average speed (km/h
or mph)
This is the average
speed calculated since
the last zero reset.
Resetting the information to zero

When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.
If dashes "---" are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer or
a qualifi ed workshop.


Current fuel consumption(l/100 km or km/l or mpg)
This is the average fuel
consumption during the
last few seconds of driving.
Information display

With the ignition on, press the INFO

button on the dashboard, to the left
of the instrument panel, several times
in succession to display the different
information:


- average fuel consumption,

- average speed,

- current fuel consumption. When the required information is
displayed, press the INFO
button for
more than two seconds to reset all of
the information to zero.

Automatic
If the ignition key remains in the
OFF position for more than 4 hours,
the information is reset to zero
automatically.

I
MONITORING
40
Set the time using the buttons as
indicated below:


)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.

)
Press the appropriate button to set
the time:

Button
H:
to set the hours
The hours digits scroll when you press
this button.

Button M:
to set the minutes
The minutes digits scroll when you
press this button.

Button 00:
to reset the minutes to zero.


- from 1 to 29 min
:
rounded down to
the previous hour,

- from 30 to 59 min:
rounded up to
the next hour.
Automatic mode

In this mode, setting is automatic using
the signal from the RDS radio stations.

)
After setting the time, press the
DISP
button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the "minutes" display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.


)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).

)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode" menu
automatically.

XI
214
AUDIO and TELEMATICS

Calendar, trip

D - Consult the driving information:
D1 - the average speed,
D2 - the average fuel consumption,
D3 - the current fuel consumption,
D4 - for speed and fuel consumption
graphs in 5 minute intervals,
D5 - choose an automatic reinitiali-
sation (key at off for more than
4 hours) or manual reinitialisation
(press [Reset]),
D6 - the distance which can still be
travelled (in relation to the fuel re-
maining and the recent average
consumption),
D7 - the distance travelled since the
fuel tank was last fi lled (press
[Refuel] to reinitialise),
D8 - the driving time (duration be-
tween the key being turned to on
then to off).
- press [Start] to measure interme-
diate times with:
D9 - the duration,

D10 - the distance,

D11 - the speed,

D12 - the fuel consumption. C - Make a note on the calendar of
special days, birthdays, ...

Use the arrows to fi nd a date and
press directly on the day required
to enter the event.
These double arrows permit
access to the driving infor-
mation screen, previous or
next.
D
C
D1D2D3
D4D5
D6D7D8
D7
D9D10D11D12