parking brake CITROEN C ZERO 2010 Owners Manual

.
Contents
Instrument panel 18
Indicator and warning lamps 19
Main battery state of charge indicator 26
Energy consumption/generation indicator 27
Distance recorder 28
Trip distance recorder 28
Lighting dimmer 29
Ser vice indicator 29
Range indicator 30
Monitoring Familiarisation
Remote control key 31
Electric windows 34
Doors 35
Boot 36
Charging fl aps 37
Access
Front seats 38
Rear seats 40
Mirrors 42
Interior fi ttings 44
Heating and Ventilation 47
Air conditioning 49
Rear screen demist - defrost 51
Comfort
Starting - stopping the vehicle 52
Manual parking brake 53
Drive selector 54
Driving
Lighting stalk 56
Automatic illumination of headlamps 58
Headlamp adjustment 58
Wiper controls 59
Courtesy lamp 60
Visibility

Familiarisation
8
Instruments and controls
1.
Parking brake.2.
Drive selector. 3.
12 V accessory socket.
4.
Passenger’s airbag deactivation.
USB por t. 5. Glove box.
6.Cup holder.
7. Windscreen demisting vents.8.Lighting and direction indicator stalk.9.
Audio system.10.Hazard warning lamps switch. 11.
Centre vents. 12 .Heating/air conditioning controls.13.Emergency or assistance call.

.Familiarisation
15
Driving safely
P.
Parking.
Press the brake pedal to come out of this
position.R.Reverse.N. Neutral. D.Drive (forward).


Drive selector
54- Check that the drive selector is in position
P
. PP- Inser t the key in the ignition switch.
- Turn the key to position 4 (START).- Hold it in this position for a few seconds,until the " READY" lamp comes on,
accompanied by an audible signal.
- Release the key.
The switch returns automatically to
position
3 (ON) .
Starting the motor
52



- Stop the vehicle.

- Keep your foot on the brake pedal.

- Put the drive selector in position P
. P

- Apply the parking brake.

- Turn the key anti-clockwise to the LOCKposition.


Stopping the motor
52

1
Monitoring
21
Warning/indicator lampStateCauseAction/Observations
Ready(readyto move off)
On fixed,
accompanied by an
audible signal when it
comes on. The vehicle is read
y to move off andyou can press the accelerator. The illumination period corresponds to the powering-
up of the vehicle.


Parking brake
On fixed. The parking brake is applied or notproperly released. Release the parking brake to switch off the warninglamp, keeping your foot on the brake pedal.
Obser ve the safety recommendations.
For further information on the parking brake, refer to
the "Driving" section.
Main batterycharge(normal or fast)
On fixed.The main battery is on charge. On completion of the charge, the lamp goes off.
Flashin
g. The charging cable is connected to
the vehicle but the main battery is not yet charging. Check the connection of the char
ging cable.

4
!
Driving
53





Manual parking brake


Applying
)Pull the parking brake lever fully up to
immobilise your vehicle.
When parking on a slope, direct your wheels against the kerb, apply the parking brake, place the drive selector in position P and switch off the ignition.

Releasing
)
Pull the parking brake lever up gently,
press the release button then lower
the lever full
y.
When the vehicle is being driven, i
f
the parking brake is still on or hasnot been fully released, this warning
lamp comes on.

Driving
54
P. Park.
This position is used for star tingthe vehicle.
To come out of the P
position, you must have your foot on the brake. R.Reverse.N.
Neutral.D.
Drive (For ward).












Drive selector
Selector positions

When you move the drive selector through the grille to select a position, the correspondingindicator is displayed in the instrument panel.


Displays in the instrument panel

With the motor running, Pappears in
the instrument panel screen.
)Press the brake pedal to come out of position P.P)Select for ward (D) or reverse ( R ) gear. R)Release the parking brake. )Ta k e your foot off the brake pedal, the
vehicle then moves off slowly to facilitatemanoeuvring. )Accelerate to go forwards or backwards. )"D"
or "R"
appears in the instrument panelscreen.


Moving off

4
!
Driving
55
To tow your vehicle, the drive selector must be in position N
, refer to "PracticalInformation".



Parking the vehicle

To stop the motor, you must select position P.P
You must apply the parking brake to immobilise
the vehicle.
To remove the key from the ignition switch, thedrive selector must be in position P.P

!
!
i
Practical information
80








Charging the main battery
)Pull lever 1
, located at the bottom of the
dashboard, driver's side, to open the
access flap for the normal charging socket(right hand side of the vehicle).
Normal charging
Before connecting, check that the power point you want to use is standardand is compatible with the current rating on the charging cable control unit. In all cases, it is recommended that your installation be checked by a qualified electrician.
There are two types of charging: normal and fast.
Normal charging should be used in pre
ference;
it is done from a domestic power point.
Fast charging is done at a compatible fastcharge station.
) Apply the parking brake and put the driveselector in position P
. P)
Switch off all electrical consumers and turn
the ignition switch to the "LOCK"
position.
Always use a genuine CITROËN charging cable.

If the ambient temperature is below -25 °C, charging may not be possible.

!
!
Practical information
84
Check the compatibility of the charging station and its charging cable with your vehicle.
)
Press latch 4to open the socket cover.)
Ensure that there is no foreign body on the
vehicle's charging socket.
Fast charging
)Apply the parking brake and put the drive
selector in position P.P)Switch off all electrical consumers and turn
the ignition switch to the "LOCK"position. )Pull lever 3 , located under the driver's seat,
outer side, to open the access flap for the
fast char
ging socket (left hand side of the
vehicle).
Do not touch the metal end of thenormal charging socket or of thecharging cable. Risk of electrocution and/or faults.
)Connect the charging cable of the charging station to the vehicle following the
instructions on use of the station.

i
Practical information
94








Changing a wheel



- A jack: for lifting the vehicle.

- A wheelbrace: for removin
g and refitting
the wheel bolts.

- A handle: for operating the jack.
These tools are not supplied with your vehicle.
Parking the vehicle

Immobilise the vehicle where it does notblock traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off the ignition and put the drive selector in
position Pto lock the wheels.
If necessary, place a chock under thewheel diagonally opposite the wheel to be changed.
You must ensure that the occupants get out of the vehicle and wait where they are safe. Never go underneath a vehicle raised using a jack; use an axle stand.