length Citroen C2 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 326
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Engines: 8HV 8HY
(4)Gear engagement balljoint Ø 10 mm.
(5) Gear selection balljoint Ø 10 mm.
Length ALength B
Gear
selection907 mm 645 mmcable(5)
Length D Length C
Gear
engagement965 mm 610 mmcable(4)B2CP3J5D
B2CP3J4C
C3

Downloaded from www.Manualslib.com manuals search engine 329
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Principles of adjusting the gear controls.
WARNING: Cables should be adjusted each time the gearbox, gear controls or power unit are
removed.
Principles.
Lock the gear lever in neutral position, using tool:9607T.
Place the gearbox in neutral.
Couple the cables on the lever.
Fit the balljoints on the gearbox lever.
Lock the cable lengths with the balljoint locking keys.
WARNING: Do not use any tool to unclip the balljoints.
To unlock the balljoint, press at the centre «a», then pull the balljoint upwards.
NOTE:Changing an individual balljoint is possible as long as the locking key is removed.
Unclip at «b», using two small screwdrivers.
Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3BXCB2CP3BYC

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1] Tool for positioning the gear lever: 9607T.
Adjustements.
WARNING: Cables should be adjusted each
time the gearbox, gear controls or power unit
are removed.
Inside the vehicle:
Remove the trim under the gear lever.
Lock the gear lever in neutral position,
using tool
[1].
Under the bonnet: Remove the air filter assembly.
Unlock the balljoint keys at «a».
Place the gear selection and control levers on
neutral.
Lock the cable lengths with the balljoint locking
keys.
Checks.
Remove the tool [1].
Check that all the gears engage without
«tightness ».
Check that the gear lever moves identically
forwards and backwards and to right and left. If it
does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3C6CB2CP3C0C

Downloaded from www.Manualslib.com manuals search engine 392
AXLES
SUSPENSION
STEERING
Adjusting the rear dummy damper
Lengths of the rear dummy damper (mm)
Grand export
346
339
346
342 Normal driving
339
318
336
XSARA REAR DAMPER
E5AP14WC
Engines
1.9 D
1.6i 16V 3door
1.6i 16V 5door
2.0i 16V (RFN) 1.4 HDi
2.0 HDi
2.0i 16V (RFS)
Estates and
Entreprise all types

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
XSARA
Steering wheel Manual steering
MANUAL STEERING SPECIFICATIONS
(a): LHD/RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAG to steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5) Steering column to support fixing:2.3 (6)Steering cardan joint fixing:2.3
(b) = Locating bush.
The locating bush must be centred in the reference window before
tightening the cardan bolts
(6).
B3EP08PD

Downloaded from www.Manualslib.com manuals search engine 395
AXLES
SUSPENSION
STEERING
22/1 Steering ratio
MANUAL STEERING SPECIFICATIONSXSARA
Manual steering (continued)
Number of teeth
Pinion Steering rack
travel
(mm)
73,56 teeth
(RH helix)29(13)
Yellow thicknessmm4,3
Left hand driveSteering rackSteering stop
colour codeNumber
of steering
wheel turns
Length of the steering track rods (Preadjustment)= 371mm (Between balljoint centres)or391mm (Between the centre of the pivot balljoint and the contact face of the steering rack balljoint).

Downloaded from www.Manualslib.com manuals search engine 396
AXLES
SUSPENSION
STEERING
XSARA POWERASSISTED STEERING SPECIFICATIONS
Steering wheel Powerassisted steering
(a): LHD = Blue.
: RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAGto steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5)Steering column to support fixing: 2.3 (6)Steering cardan joint fixing: 2.3
(b) = Locating bush.
The locating bush must be centred in the reference
window before tightening the cardan bolts
(6).
B3EP08QD

Downloaded from www.Manualslib.com manuals search engine 398
AXLES
SUSPENSION
STEERING
POWERASSISTED STEERING SPECIFICATIONS
XSARA
Powerassisted steering (Continued)
Number of teeth
Pignon Steering rack
travel
(mm)
71,7(
*)
(RH helix)
28
Protector colour Vehicles
BLACKAll Types (except 1.6i 16V 1.9 TD)7
Steering valve
Number of teeth (*) 3,3
LHDSteering rackNumber of
steering wheel
turns
Length of the steering link rods (Preadjustment)= 371mm (Between balljoint centres)or391mm (Between the centre of the pivot balljoint and the contact face of the steering rack balljoint).
1.6i 16V 1.9 TDORANGE8
18,8/1 Steering
ratio

Downloaded from www.Manualslib.com manuals search engine 409
AXLES
SUSPENSION
STEERING
Steering Rack pinion Number of teeth Number of steering Turning circle Turning circle
rack travel in rack wheel turns between walls between kerbs
Left hand drive
71,7 x 2
LH helix28 Teeth 3,22 12 m 11,48 m
Right hand driveRH helix
Engines Steering valve
NFV 6FZ RFN RHY
number of teeth :7
Length of the steering link rods (preadjustment):
Between balljoint centres =
392 mm.
Between the centre of the pivot balljoint and the contact face of the steering rack balljoint =
412 mm.
STEERING COLUMN SPECIFICATIONSXSARA PICASSO