Console Citroen C2 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
NOTE:The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch. Automatic gearbox ECU.
Electrical harnesses.
Battery voltage.
Remove:
The gear lever knob
(1)(pull upwards).
The cover (2)(Unclip).
The top of the central console (3).
Unlock the «shift lock» (4)with the aid of a screwdriver.
Move the gear selection lever out of position «P».
Engine: KFV
C3
C5FP0ETCB2CP3GZC

Downloaded from www.Manualslib.com manuals search engine 419
BRAKES
C5FP0ELD
HANDBRAKE (Adjustment)
Adjustment.
Lift and chock the vehicle.
Remove:
The rear cover
(8).
The nut (9).
The handbrake trim (6).
The gear lever gaiter (5).
The front cover (3).
The screws (1).
Disconnect the connectors of the following components:
The cigar lighter
(2).
The electric window buttons (4).
Remove the central console
(7).
WARNING:Check that the brake cables are correctly
routed under the vehicle.
Slacken the handbrake lever.
Press gently on the brake pedal
(Then repeat the ope
ration 3 times).
Pull vigorously on the handbrake lever 4 or 5 times.
C2

Downloaded from www.Manualslib.com manuals search engine 420
BRAKES
B3FP16ED
HANDBRAKE (Adjustment)
Adjustment (continued).
A
: Drum brakes.B:Disc brakes.(10)Nut for adjusting cable tensions.
Remove:
The rear wheels.
The drums
(according to version).
Release the handbrake.Use a gauge set to measure at
«a»the travel of the lever
from its stop.
Adjust the nut
(10)to obtain a travel of less than or equal
to 1 mmat «a».
Refit the brake drums without tightening them (according
to version).
Action the handbrake lever 8 times with an effort of 40 m.daN.
With the handbrake released, check the travel of the
lever at
«a», using a gauge set.NOTE:The travel should be less than 1 mmand more
than 0,05 mm.
Refit:
The brake drums. The wheels.
The central console.
Check the operation of the handbrake.
C2

Downloaded from www.Manualslib.com manuals search engine 434
BRAKES
C5FP0ELD
HANDBRAKE (Adjustment)
Adjustment.
Lift and chock the vehicle.
Remove:
The rear cover
(8).
The nut (9).
The handbrake trim (6).
The gear lever gaiter (5).
The front cover (3).
The screws (1).
Disconnect the connectors of the following components:
The cigar lighter
(2).
The electric window buttons (4).
Remove the central console (7).
WARNING:Check that the brake cables are correctly
routed under the vehicle.
Slacken the handbrake lever.
Press gently on the brake pedal
(Then repeat the operation3 times).
Pull vigorously on the handbrake lever 4 or 5 times.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 435
BRAKES
B3FP16ED
HANDBRAKE (Adjustment)
Adjustment (continued).
(10)
Nut for adjusting cable tensions
Remove:
The rear wheels.
The drums
(according to version).
Release the handbrake.Use a gauge set to measure at
«a»the travel of the lever
from its stop.
Adjust the nut
(10)to obtain a travel of less than or equal
to 1 mmat «a».
Refit the brake drums without tightening them (accor
ding to version).
Action the handbrake lever 8 times with an effort of
40 m.daN.
With the handbrake released, check the travel of the
lever at
«a», using a gauge set.NOTE:The travel should be less than 1 mm and more
than 0,05 mm.
Refit: The brake drums.
The wheels.
The central console.Check the operation of the handbrake.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 448
BRAKESBRAKE SPECIFICATIONS
Electrical circuit
ComponentsRef.
SupplierPart no.Observations
42wayconnector.
Integral to the hydraulic block..Changing only the ECU is prohibited.
2waygrey connector.
The sensors are inductivetype.Tightening torque:
0,8 ± 0,2 m.daN.
2waygrey connector.
The sensors are inductivetype.Mounted on the brake caliper support.
Nonadjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
2waygrey connector.
The sensors are inductivetype.
Mounted on the suspension arm.
Nonadjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
Incorporated in the COM 2000.
6wayblue connector.
Located on the central console.
6way connector.
Toothed wheel:
48 teeth.
Integral with the driveshaft stub housing for
the front wheels, joined to the hub bearing for
the rear wheels.
XSARA
5.7 ESP
0 265 006 389
0 265 006 202
0 265 006 203
0 265 006 441 BOSCH
VALEO
BOSCH
GKNElectronic
ECU
Front wheel sensor
Rear wheel sensor
(disc brakes)
Rear wheel sensor(Saloon: drum brakes)
Rear wheel sensor(Estate: drum brakes)
Steering angle sensor
Gyrometer/accelerometer sensor
Toothed wheel7
5
12
13
4

Downloaded from www.Manualslib.com manuals search engine 450
BRAKES
HANDBRAKE
XSARA
Checking and adjusting the handbrake.
Remove the handbrake console.
Jack up and chock the vehicle with the rear wheels hanging free. Check the correct routing of the brake cables under the vehicle.
Apply and release the handbrake ten times. Set the handbrake to the
3rd notch.
Tighten the nut (1)until the rear brakes are applied.
Pull the handbrake lever vigorously 4 to 5 times.
Set the handbrake to the 3rd notch.
Check that the rear brakes are applied.
Check that the wheels can be turned freely by hand with the
handbrake released.
Lower the vehicle. Refit the handbrake console.
B3FP095D