Servo Citroen C3 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 421
BRAKES
B3FP15XC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]
Generic bleeding apparatus :«LURO»Bleeding, refilling.
Draining.
Drain the brake fluid reservoir (1)to the maximum(if necessary, use a clean syringe).
Disconnect the connector (4).
Uncouple the pipe (2).
Unscrew the shaft (3).
Remove the reservoir (1).
Empty the brake fluid reservoir (1).
Clean the brake fluid reservoir (1).
Refit:
The brake fluid reservoir
(1).
The shaft (3).
Couple the pipe (2).
Reconnect the connector (4).
Filling the braking system.WARNING:Use only those hydraulic fluids that are approved and recommended.
Fill the brake fluid reservoir (1).
Bleeding the braking system.WARNING:During the bleeding operation, take care to maintain the level of brake fluid in the reservoir
and to top it up, using only brake fluid that is clean and clear.
C2

Downloaded from www.Manualslib.com manuals search engine 423
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles. Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw. Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C2

Downloaded from www.Manualslib.com manuals search engine 430
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit
(b)Electrical circuit
(1)Master cylinder in tandem
(2) Braking servo
(3)Brake caliper (or drum at the rear)
(4) Hub equipped with a bearing with an integral magnetic wheel
(48 pairs of poles)
(5) Wheel sensor
(6) Brake fluid level sensor
(7) Hydraulic block plus ECU
(8)Stoplamp switch
(9)Instrument panel
(10)Diagnostic socket
(11)Builtin systems interface (BSI)
B3GP02RP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 432
BRAKESBRAKE SPECIFICATIONS
Brake pedal gear Front brakes Rear brakes
(16)
Servo fixing: 2,2 ± 0,3
(17) Fixing on master cylinder: 2 ± 0,5(12)Yoke fixing on caliper:10,5 ±1
(13)Yoke fixing on caliper: 3 ± 0,3(14)
Rear caliper fixing on arm: 5,3 ± 0,5
(15)Yoke fixing on caliper:2,7 ± 0,5
Tightening torques (m.daN).
B3FP166DB3FP164CB3FP165C
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 436
BRAKES
B3FP15XC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]
Generic bleeding apparatus: «LURO» or similar.
Bleeding,refilling.
Draining.
Drain the brake fluid reservoir (1)to the maximum (if necessary, use a clean syringe).
Disconnect the connector (4).
Uncouple the pipe (2).
Unscrew the shaft (3).
Remove the reservoir (1).
Empty the brake fluid reservoir (1).
Clean the brake fluid reservoir (1).
Refit:
The brake fluid reservoir
(1).
The shaft (3).
Couple the pipe (2).
Reconnect the connector (4).
Filling the braking system.WARNING:Use only those hydraulic fluids that are approved and recommended.
Fill the brake fluid reservoir (1).
Bleeding the braking system.WARNING:During the bleeding operation, take care to maintain the level of brake fluid in the reser
voir and to top it up, using only brake fluid that is clean and clear.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 438
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container. Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 447
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ESP (BOSCH 5.7)
(A) Hydraulic circuit(B) Electrical circuit
(1)Master cylinder in tandem(2)Braking servo(3)Brake caliper (or drum at the rear)(4)Toothed wheel(5) Wheel sensor(6)Brake fluid level sensor(7)Hydraulic block plus ECU(8) Stoplamp switch(9)Instrument panel(10)Diagnostic socket(11)Builtin systems interface (BSI)(12)Steering angle sensor(13)Gyrometer/accelerometer sensor(14)Switch
B3HP004P
XSARA

Downloaded from www.Manualslib.com manuals search engine 458
BRAKESBLEEDING THE BRAKESXSARA PICASSO
Tools.Bleeding equipment of type «LURO» or similar.IMPERATIVE: For bleeding the secondary circuit, use ELIT, LEXIA or PROXIA diagnostic tools.
Draining.
Drain the brake fluid reservoir as empty as possible using a syringe.
Disconnect the brake fluid warning lamp connector.Retrieve the brake fluid reservoir from its supply pipes by pulling upwards.
Finish emptying the reservoir of brake fluid.
Clean the brake fluid reservoir.
Refit the brake fluid reservoir.
Reconnect the brake fluid warning lamp connector.
Filling.Refill the reservoir with brake fluid.WARNING:Use only the recommended hydraulic fluids.
Bleeding.
NOTE:Two technicians are required.
IMPERATIVE:During bleed operations, ensure that the level of brake fluid is maintained in the
reservoir and top it up, use only new brake fluid.
Bleed each wheel cylinder, proceeding in the following order:
Rear right hand wheel.
Front left hand wheel.
Rear left hand wheel.
Front right hand wheel.

Downloaded from www.Manualslib.com manuals search engine 486
ELECTRICAL
SYSTEM
MANULLI calibrated seal (3).
Direction of fitting of the seal (3).
Before fitting the seal, amply lubricate the seal with air conditioningcompressor oil
(SP10). The condenser
(5)has a cylinder (6)incorporating the function of aircon
fluid reservoir and with integral filtering cartridge.The inlet
(7)and the outlet (8)of the condenser (5)are equipped with
new seals (3) (MANULLI).
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Seals (MANULLI seal)
Condenser (MANULLI seal)
C5HP18VDC5HP18XD
C2 C3 XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 490
AIRCONAIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Changing the filtering/drying cartridge
Tools.
[1]
Charge station :(according to workshop equipment)[2]TORX adaptor: TORX 70 FACOM
[3]Inertia extractor:1671T Tool kit 4114T
[4]Endpiece Ø 20 : 1671T.D20
[5]Set of plugs: ().0188.T
[6]Circlip pliers: FACOM
Removing.
Depressurise the aircon circuit, using tool [1].
Remove the grille.At
«a», remove the pin and the plastic cover.
Unclip the condenser at «b»and «c», using a screwdriver.
Tilt the condenser towards the front.
Lift and release the condenser.Clean the area around the cap
(3).
Remove the plastic cap (3), using tool [2].
Remove the safety circlip (4), using tool [6].
Position the tool [3]and[4]in the aperture of the cartridge (5).
Extract the cartridge from the reservoir (6), using tool [3]and [4].
Block the reservoir (6), using tool [5].
C4AP163CC4AP164CC4AP166CC4AP165C
C2 C3 C3 PLURIEL