engine timing Citroen C3 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 148
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV NFU
B1BP2M7CB1BP2M9CB1BP2M8C
Tools.
[1]
Engine flywheel peg: 4507T.A
[2]Camshaft pulley peg : 4507T.B
[3a]Camshaft peg: 4533TA.C1
[3b] Camshaft peg: 4533TA.C2
[4]Dynamic tensioner roller pin: 4200T.H
[5]Belt retaining pin: 4533T.AD
[6]Pliers for removing plastic pins: 7504T
Checking the valve timing.
Engines:
HFX – KFV – NFU.
Raise and support the front RH side of the vehicle.
Disconnect the battery positive terminal.
Engage 5th gear.
Remove the oil filter
(1).
Engines:HFX – KFV.
Remove: The timing top casing (2).
Turn the wheel to rotate the engine (normal direction of rotation).
Peg the camshaft pulley, using tool [2].
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
149
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
B1BP2MAC
Checking the timing (continued).
Engine:
NFU.
Place a jack under the engine, peg the engine.
Remove:
The engine support
(4)complete.
The timing casing
(3).
The sparking plugs
(eases engine rotation).
Turn the wheel to rotate the engine
(normal direction of rotation).
Position the pegs
[3a]and[3b].
Peg the flywheel, using tool
[1].
If the setting is not correct, recommence the operation.
Remove the tools
[1], [2], [3a]and [3b].
Complete the refitting.
B1BP2MBCB1EP18MC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 150
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV
B1BP2MBCB1BP2M9CB1BP2MDC
Setting the timing.Preliminary operation.Lift and support the vehicle, wheels hanging.
Disconnect the battery.
Remove:
The front RH wheel.
The splashshield, using tool
[6].
The accessories belt (See corresponding operation).
The crankshaft pulley.
The oil filter.
Place a jack under the engine, peg the engine.
Removing.
Engines:HFX – KFV.Turn the engine by means of screw (1)(normal direction of rotation).
Remove the timing casings.Peg the camshaft pinion, using tool
[2].
Peg the flywheel, using tool [1].
Remove:
The fixing screws
(2).
The upper engine support (3).
B1BP2MCC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
151
CHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV
B1BP2MECB1EP18NC
Setting the timing (continued).
Engines:
HFX – KFV.
Slacken the screws (4)without removing them.
Remove the bottom engine support assembly
(5), and the fixing screws (4).
Slacken the nut
(6).
Completely detension the belt by acting on the tensioner roller
(7).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller turns freely (no tight spot).
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 152
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
B1BP2MBC
Engine:NFU.
Setting the timing (continued).
Remove:
The bottom plastic casing.
The engine support
(9).
The middle support.
The timing cover
(8).
Peg the flywheel, using tool
[1].
Position the tools
[3a]and [3b].
B1BP2MFCB1EP18MC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
153
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
B1EP18PC
Setting the timing (continued).
Engine:
NFU.
Slacken the tensioner roller.
Turn the tensioner roller so as to be able to position the tool
[4], with the aid of an Allen key placed at «a».
Turn the tensioner roller towards the right to bring it to the index
«c»in position «b».
Peg the tensioner roller in this position in order to slacken the timing belt to the maximum.
IMPERATIVE: Never make the dynamic tensioner roller turn by a complete rotation.
Remove the timing belt (8).
Check that the rollers
(9)and (10)turn freely (no tight spot).
B1EP18QC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 154
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV
B1EP18QC
Setting the timing (continued).
Engines:
HFXKFV.
Refit.
WARNING: Respect the direction of fitting of the belt
(the arrows «d» indicate the direction of rotation
of the crankshaft).
Refit the timing belt.
Position the timing belt, belt
«e»well tensioned, in the following order:
Crankshaft pinion, hold the belt using tool [5].
Camshaft pulley.
Coolant pump pulley. Tensioner roller.
Remove the pegs
[1]and [2].
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
155
CHECKING AND SETTING THE VALVE TIMING
Engines: KFX KFV NFU
Setting the timing (continued).
Engines:
HFXKFV.Refitting.
NOTE:Check that the pegs [1]and [2]are in place.WARNING:Respect the direction of fitting of the timing belt, the arrows «d»indicate the direction of rotation
of the crankshaft.Refit the timing belt.
Position the timing belt, belt
«e»well tensioned, in the following order:
Crankshaft pinion, hold the belt using tool [5].
Camshaft pulley. Coolant pump pulley.
Tensioner roller.
Remove the tools
[1], [2].
Engine:NFU.Fit the timing belt in position in the following order:
Inlet camshaft pulley. Exhaust camshaft pulley.
Guide roller.
Crankshaft pulley.
Position tool
[5].
Coolant pump pulley.
Dynamic tensioner roller.
Remove the tools
[1], [3]and [5].B1EP18RC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 156
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
B1EP18SD
Timing belt overtensioned.
A:Engine:HFX – KFV.
B:Engine:NFU.
Turn the tensioner roller
(7)with the aid of a hexagonal spanner at «a».
Bring the index
«c»to position «f», to tension the belt to the maximum of the
interval indicated.Hold the tensioner roller
(7), using tool [4].
Tighten the fixing nut of the tensioner roller, tightening to
1 ± 0,1 m.daN.
Turn the crankshaft by
4 rotations(normal direction of rotation).
IMPERATIVE: Never make the crankshaft rotate backwards.
Make sure that the timing is correctly set by refitting the tools [1], [2]and [3].
Remove the tools
[1], [2]and [3].
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
157
CHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV NFU
B1EP18TD
Adjusting the fitting tension of the timing belt.
A:Engine:HFX – KFV.
B:
Engine:NFU.
Slacken the nut while maintaining the position of the tensioner roller, with the aid of
a hexagonal spanner at
«a».
Next bring the index
«c»to its adjusting position «a».
The index
«c»should not go beyond the notch «g».
WARNING:The index«c» must not go beyond the notch«g».If it should do this,
restart the timing belt tensioning operation.
Hold the tensioner roller
(7)in this position, with the aid of a hexagonal spanner.
Tighten the tensioner roller fixing nut to :
2 ±0.2 m.daN.(HFX - KFV engines)
2.2 ± 0.2 m.daN.(NFU engine)
IMPERATIVE: The tensioner roller must not rotate during the tightening of its
fixing. If it does, restart the timing belt tensioning operation.
Complete the refitting.
C2 C3 C3 PLURIEL