o2 sensor Citroen C3 2004 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 316
CLUTCH
GEARBOX
TRANSMISSION
MA/5 PILOTED MANUAL GEARBOX
Engines: KFV 8HX
Features.
The piloted gearbox is a modern manual gearbox with technology that offers
enhancements in every driving situation.
The piloted manual gearbox has two operating programmes:

«Sequential»programme.
«Automatic»programme.
The piloted manual gearbox has:
A gearbox ECU
(supplier:SIEMENS). A gearbox actuator with two electric motors (supplier:SACHS).
A clutch actuator with one electric motor (supplier:SACHS).
A gearbox input speed sensor.
The piloted manual gearbox has no gear control cable and no clutch cable.Changes of gear and clutching/declutching are activated by the gearbox
actuator and the clutch actuator.
Lubrication.
Oil capacity : 2 ± 0,15 litres.
Checking of oil level : No oil level check.(*)Lubrication intervals : Lubricated «for life».
(*)= Only a visual check of the sealing at each engine oil change interval.
B2CP3SUD
C2

Downloaded from www.Manualslib.com manuals search engine 337
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Tightening torques (m.daN).
(1)
Oil flow modulation electrovalve fixing: 1 ± 0,2
(2)
Heat exchanger fixing:5 ±1
(3)
Output speed sensor fixing:1 ±0,2
(4)
Output speed sensor fixing: 1 ± 0,2
(5)
Oil overflow and drain fixing: 4 ± 0,2
(6)
Oil level plug:2,4 ±0,4
(7)
Oil pressure sensor fixing: 0,8 ± 0,1
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3EDDB2CP311D

Downloaded from www.Manualslib.com manuals search engine 340
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
In passenger compartment.The gear selector is guided by the shape of the stepped gate and by a retaining spring which
pulls it to the left hand side.
The gear selector control has
5 positions:
Position
«P»: Park (locking and immobilisation of the vehicle).
Position «R»:Reverse gear.
Position «N»: Neutral.
Position «D»: Drive (use of the 4 gears in their autoadaptive automatic function).
Position «M»: Manual (this position lets the driver select his own gears in sequential mode
by pulling the gear selector to «M-»or pushing it to «M+»).
NOTE:Only the positions «P»or «N»authorise the starting of the engine.
In position
«M», selection is by an electronic sensor located close to the gear lever.
The variation of flux necessary to the movement of the sensor cells is obtained by a magnet
located on the lever itself. This enables the change of status.
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H7DB2CP3MUD
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 362
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV NFU 8HX
Steering mechanism
Tightening torques (m.daN.).
(4)
Balljoint fixing on pivot:3,5 ± 0,3
(5)
Steering rod locknut: 5 ± 0,5
(8)
Threaded washer
(9)Stud: 0,8 ± 0,1
(10)
Flat washers
(11)Fixing of mechanism on subframe:8 ± 0,8
Connectors.
(6)
Supply of electric assistance motor
(7)Torque sensor signals
HFX KFV 8HXNFU
Electric motor 60 A 65 A
Steering rack travel2x722x64
Steering ratio45,6/1
Number of rotations of
steering wheel 3,22,8
Inner angle of lock 38° 32°30’
Outer angle of lock 32°24’ 28°42’
B3EP13JD
C2

Downloaded from www.Manualslib.com manuals search engine 377
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV KFU NFU 8HX 8HW 8HV 8HY
Steering mechanism
Tightening torques m.daN.
(4)
Balljoint fixing on pivot: 3,5 ± 0,3
(5)
Steering rod locknut: 5 ± 0,5
(8)
Threaded washer
(9) Stud: 0,8 ± 0,1
(10)
Flat washers
(11)Fixing of mechanism on subframe:8 ±0,8
Connectors.
(6)
Supply of electric assistance motor
(7) Torque sensor signals
HFX KFV 8HX 8HWKFV (BVA)
NFU 8HY 8HV
Electric motor 60 A 65 A
Steering rack travel2x72 2x64
Steering ratio45,6/1
Number of rotations
3,22,8
of steering wheel
Inner angle of lock 38° 32°30’
Outer angle of lock 32°24’ 28°42’
B3EP13JD
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 416
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit(b)Electrical circuit
(1)Master cylinder in tandem(2)Braking servo(3)Brake caliper (or drum at the rear)(4)Hub equipped with a bearing with an integral magnetic wheel(48 pairs of poles)(5)Wheel sensor(6)Brake fluid level sensor(7)Hydraulic block plus ECU(8)Stoplamp switch(9)Instrument panel(10)Diagnostic socket(11)Builtin systems interface (BSI)
B3GP02RP
C2

Downloaded from www.Manualslib.com manuals search engine 417
C2
BRAKE SPECIFICA TIONS
(7) Hydraulic blockBRAKESRef. Components Supplier Part no. Observations
ABS MK 70 Mounted on the front LH chassis
Hydraulic block 96 514 120 80 member.
ESP ABS MK.60 4 adjustment channels.
7 96 490 288 80
ABS MK.70
ECU ESP ABS 26way connector.
MK 60 Integral to the hydraulic block.
2way blue connector.
The sensors are inductivetype.
Front wheel sensor TEVES Mounted on the pivot
Nonadjustable airgap:
0.16 to 1.6 mm.
596 387 201 80Tightening torque:0.8 ±0.2 m.daN.
2way blue connector.
The sensors are inductivetype
Rear wheel sensor Mounted on the suspension arm.
Nonadjustable airgap
: 0,35 à 1,6 mm.
Tightening torque:0,8 ± 0,2 m.daN.
Hub equipped with a bearing with
4 Hub bearing SNR an integral magnetic wheel
(48 pairs of poles).B3FP7BVC

Downloaded from www.Manualslib.com manuals search engine 430
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit
(b)Electrical circuit
(1)Master cylinder in tandem
(2) Braking servo
(3)Brake caliper (or drum at the rear)
(4) Hub equipped with a bearing with an integral magnetic wheel
(48 pairs of poles)
(5) Wheel sensor
(6) Brake fluid level sensor
(7) Hydraulic block plus ECU
(8)Stoplamp switch
(9)Instrument panel
(10)Diagnostic socket
(11)Builtin systems interface (BSI)
B3GP02RP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 447
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ESP (BOSCH 5.7)
(A) Hydraulic circuit(B) Electrical circuit
(1)Master cylinder in tandem(2)Braking servo(3)Brake caliper (or drum at the rear)(4)Toothed wheel(5) Wheel sensor(6)Brake fluid level sensor(7)Hydraulic block plus ECU(8) Stoplamp switch(9)Instrument panel(10)Diagnostic socket(11)Builtin systems interface (BSI)(12)Steering angle sensor(13)Gyrometer/accelerometer sensor(14)Switch
B3HP004P
XSARA

Downloaded from www.Manualslib.com manuals search engine 448
BRAKESBRAKE SPECIFICATIONS
Electrical circuit
ComponentsRef.
SupplierPart no.Observations
42wayconnector.
Integral to the hydraulic block..Changing only the ECU is prohibited.
2waygrey connector.
The sensors are inductivetype.Tightening torque:
0,8 ± 0,2 m.daN.
2waygrey connector.
The sensors are inductivetype.Mounted on the brake caliper support.
Nonadjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
2waygrey connector.
The sensors are inductivetype.
Mounted on the suspension arm.
Nonadjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
Incorporated in the COM 2000.
6wayblue connector.
Located on the central console.
6way connector.
Toothed wheel:
48 teeth.
Integral with the driveshaft stub housing for
the front wheels, joined to the hub bearing for
the rear wheels.
XSARA
5.7 ESP
0 265 006 389
0 265 006 202
0 265 006 203
0 265 006 441 BOSCH
VALEO
BOSCH
GKNElectronic
ECU
Front wheel sensor
Rear wheel sensor
(disc brakes)
Rear wheel sensor(Saloon: drum brakes)
Rear wheel sensor(Estate: drum brakes)
Steering angle sensor
Gyrometer/accelerometer sensor
Toothed wheel7
5
12
13
4