Steering Citroen C3 2004 1.G Service Manual

Downloaded from www.Manualslib.com manuals search engine 381
AXLES
SUSPENSION
STEERING
Front axle Rear axle
AXLE GEOMETRY
Reference heights
: 4300T N°RPO 9429
# Tools. [1] Gauge for measuring the radius of wheels with 4 bolts
Setting the reference height.
Front
Fr ont
Measure the dimension «R1».
Calculate the dim.
H1 = R1 L1.Measure the dimension
«R2».
Calculate the dim.
H2 = R2 + L2.
Compress the suspension until the values
(H1)and (H2)are obtained.
NOTE:The difference in height between the two sides should be less than10 mm.
XSARA
Reference heights
(in mm)115,5
90,575,5 73
8388 103 Engines2.0i 16V
(RFS)All engines (except
2.0 i 16V and CRD)All CRD
engines 2.0i 16V
(RFS)All Saloon (except
2.0i 16V and CRD)EstateAll CRD
engines
B3CP04AD

Downloaded from www.Manualslib.com manuals search engine 382
AXLES
SUSPENSION
STEERING
ESSENTIAL: When checking the suspensions, the vehicle should be at reference height.
XSARA
AXLE GEOMETRY
Values of the front and rear suspensions, at reference height
Tools.
Compress the suspension, to obtain the values at reference height.
[1]Set of two suspension compressors: 9511T.A
[2] Set of four straps : 9511T.B
[3] Set of four shackles :9511T.C
A > B =
Negative figure: – = TOEOUT
A < B = Positive figure: + = TOEIN
WARNING
B3CP04LC

Downloaded from www.Manualslib.com manuals search engine 383
AXLES
SUSPENSION
STEERING
AXLE GEOMETRYXSARA
Values of the front and rear suspensions, at reference height
Front axle
Adjustable
YES
NO
Pivot angle
Camber CastorTracking
Camber
(*) CRD
= Difficult road conditions.
Tracking
Tolerances
± 30’ ± 30’ ±18’ ± 1 mm 1,5 ± 1 mm
0°15’ ± 10’
(toe-out)
3° 2°55’ 3° ± 07’ 2°55’
10°22’ 11° ± 07’ 10°26’
0°12’ 0° ± 07’ 0°07’ 10°40’
0°
Saloon or
entreprise KFWSaloon all engine
typesexcept KFW
Estate
all engine types
except CRD (*)
Rear axle
NO YES
Saloon CRD (*)
KFW2.0i 16V (RFS)Saloon CRD (*)
all engine types
except KFW
Estate CRD (*)
all engine types
Adjustable TolerancesSaloon all engine types
Saloon entreprise2.0i 16V (RFS)Estate
all engine typesSaloon CRD (*)
all engine types
Estate CRD (*)
all engine types
10°44’
± 1,3 mm
± 15’4,54 ± 1,3 mm 5,1 ± 1,3 mm 4,27 ± 1,3 mm 3,45 ± 1,3 mm
0°41’ ± 11’ 0°46’ ± 11’ 0°39’ ± 11’ 0°31’ ± 10’
0°57’ 0°58’ 0°59’

Downloaded from www.Manualslib.com manuals search engine 384
AXLES
SUSPENSION
STEERING
XSARA
AXLE GEOMETRY
a= Angle which defines the tracking between the front and rear axles.
Its value must not exceed
12'.
B3CP04UC

Downloaded from www.Manualslib.com manuals search engine 385
AXLES
SUSPENSION
STEERING
XSARA
FR ONT AXLE
Tightening torques (m.daN).
(1)
Damper nut: 4,5 ± 0,4
(2)Cup screw : 2,5 ± 0,3
(3)Suspension leg(4)Antiroll bar link rod upper balljoint: 3,7 ± 0,3
(5)Suspension leg pivot (hollow pivot): 4,5 ± 0,5
(5) Suspension leg pivot (pivot «H»): 5,5 ± 0,5
(6)Antiroll bars(7)Antiroll bar link rod lower balljoint:3,7 ± 0,3
(8)Pivot lower balljoint:4 ± 0,4
(9)Driveshaft nut: 32,5 ± 2,5
(10) Wheel bolt:9 ±1
(11)Lower arm front mounting: 7,6 ± 0,7
(12) Lower arm rear mounting
and antiroll bar bearing: 6,8 ± 0,6
(13)Screw under rear mounting: 3,1 ± 0,3
(14) Balljoint fixing on lower arm:5 ±0,5Subframe to bodyshell fixing screw: 8,5 ± 0,8
B3CP040PB3CP041D
VehiclesRPO 8667#are all equipped
as standard with ventilated discs.

Downloaded from www.Manualslib.com manuals search engine 386
AXLES
SUSPENSION
STEERING
FRONT AXLE
Evolution: Suspension arm balljoint
XSARA
Application from RPO: 7968.
New components:
Suspension arm balljoint.
Pivot.
Old fitting
ØA = 16 mm.
New fittingØA = 18 mm.
Repair requirements.
ESSENTIAL:Swapping of old and new components is forbidden.
It is permitted to fit a new pivot/balljoint assembly on one side of an old
vehicle.
Replacement Parts.
The old components are still available from Replacement Parts.
B3CP054D

Downloaded from www.Manualslib.com manuals search engine 387
AXLES
SUSPENSION
STEERING
FRONT AXLE
Antiroll bar
Diameter
Engine ver sions
1.6i 1.6i 16V 1.9 D
2.0i 16V (RFV) 1.4 HDi 2.0 HDi
19 Blue
20
21Yellow
White
2.0i 16V (RFS)colour reference
XSARA
Saloon
Estate
Saloon

Downloaded from www.Manualslib.com manuals search engine 388
AXLES
SUSPENSION
STEERING
FRONT AXLE
XSARA
Pivot balljoint:
Manual steering, groove at «b».
Power steering, groove at
«b».
Tongue «a» towards the front.
B3CP049C
B3CP043D

Downloaded from www.Manualslib.com manuals search engine 389
AXLES
SUSPENSION
STEERING
XSARA
REAR AXLE
Tightening torques (m.daN).
(1)
Antiroll bar lever: 3,2 ± 0,3
(2)Antiroll bar(3)Transversal torsion bars(4)Rear crossmember flanges: 8,3 ± 0,8
(5) Front silentblocks: 5,5 ± 0,5
(6)Rear silentblocks: 4,5 ± 0,4
(7)Antivibration clamp(8) Damper pin:9,6 ± 0,9
(9)Stub axle nuts (lubricated):18,5 ±1
NOTE:
The RHtorsion bar is identified by 1 paint line.
The
LHtorsion bar is identified by 2 paint lines.
B3DP04SP

Downloaded from www.Manualslib.com manuals search engine 390
AXLES
SUSPENSION
STEERING
REAR AXLE
XSARA
Vehicles
Engines Diameter colour reference Diameter colour referenceTorsion bars (mm) Antiroll bar (mm)
3door Entreprise
19,3 Violet 19 Orange
3 and 5door TT
exc. Entreprise
Estates All types
18,7
20 Grey20 Green
3 and 5door TT19,3
Violet19 Orange
Estates All types20 Grey20 Green
3door VTS
3 and 5door TT
Estates All types21Light green
23
19,3Violet19
20
Grey20Without colour,
or white sticker yellow 18 Blue
1.9 D
1.6i 16V 2.i 16V
1.4 HDi 2.0 HDi
2.0i 16V
Grand Export
«CRD»
Orange
Green