too low Citroen C3 2004 1.G Service Manual

Page 268 of 523

Downloaded from www.Manualslib.com manuals search engine 264
INJECTION
CHECKS: TURBO PRESSURE
Engines: 8HV 8HY
Tools.
[1]Pressure gauge for checking boost pressure: 4073T.A
[2]Sleeve for checking boost pressure: ().0171.F
Checks.
IMPERATIVE:
Respect the following test conditions:
Engine at operating temperature.
Vehicle in running order. Engine under full load.
Preparation.Remove the clips (1).
Fit the tool [2]in the place of the duct (2).
Couple the sleeve [2]on the pressure gauge [1] using the tube «a».Mode of operation.Position tool [1]in the vehicle.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of
1000 rpm.
Check the pressure:0,6 ± 0,05 bar (1500 rpm).
Accelerate freely (change from fourth gear to third gear)Check the pressure:0,9 ± 0,05 bar(between 2500 and 3500 rpm).
Remove tools[1],[2]at «a».
Reposition the tube (2)and tighten the clip (1).
C5FP0EJC
B1BP2NBD
C3

Page 269 of 523

Downloaded from www.Manualslib.com manuals search engine 265
INJECTION
CHECKS: TURBO PRESSURE
Engines: 9HZ 9HY
IMPERATIVE: Respect the safety and cleanliness requirements.
Preparation.
IMPERATIVE: Respect the following test conditions:
Engine at operating temperature.
Vehicle in running order.
Engine under full load.
Connect the diagnostic tool to the vehicle’s diagnostic socket, carry out parameter measures.
Mode of operation.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of
1000 rpm.
Check the pressure:0,6 ± 0,05 bar (1500 rpm).
Accelerate freely (change from fourth gear to third gear).
Check the pressure:0,9 ±0,05 bar(between 2500 and 3500 rpm).
XSARA PICASSO

Page 270 of 523

Downloaded from www.Manualslib.com manuals search engine 266
INJECTION
CHECKS: TURBO PRESSURE
Engine: RHZ
XSARA PICASSO
Tools.
[1]
Pressure gauge for checking boost pressure: 4073T.A Kit 4073T
[2]Sleeve for checking boost pressure: 4185T
[3]Adaptor sleeve: 4229T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running
temperature. Vehicle in running order at full load.
Preparation.
Remove the collar fixing (3).
Insert the tool [2]connected with tool [3], between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the sleeve [2]to the tool [1]with its tube «a».Procedure. Start the engine.
Engage first gear and start the engine.
Engage the gears up to third gear.
Decelerate to
1000 rpm.
Accelerate hard, and check the pressure:0.6 ± 0.05 Bar (1500 rpm).
Accelerate freely in kickdown (changing from fourth to third gear).
Check the pressure:0.95 ± 0.05 Bar(between 2500 and 3500 rpm).
Remove the tools, reposition the pipe (1)and refit the collar (3).B1HP12JD

Page 271 of 523

Downloaded from www.Manualslib.com manuals search engine 267
INJECTION
CHECKS: TURBO PRESSURE
Engine: RHY
Tools.
[1]
Pressure gauge for checking boost pressure: 4073T.A Kit 4073T
[2]Sleeve for checking boost pressure: 4185T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running temperature.
Vehicle running at full load.
Preparation.
Remove the collar (3) and the sleeve.
Insert the tool [2]between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the pressure gauge [1]to the tool [2]with its tube «a»long enough for the gauge to
be positioned inside the vehicle.
Procedure. Start the engine.
Engage first gear and start the engine.
Engage the gears up to third gear.
Decelerate to
2000 rpm.
Gradually accelerate.
Check the pressure:
0.95 ± 0.05 Bar Remove the tools, refit the collars (3)and the sleeve.B1BP1ZXD
XSARA PICASSO

Page 273 of 523

Downloaded from www.Manualslib.com manuals search engine 269
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
Vacuum pump.
Connect the tool [1]on the vacuum pump (1).
Start the engine.
Pressure should be
0.8 barat 780 rpm.Boost pressure regulator electrovalve. Connect the tool [1]between the electrovalve (2)and the valve (3)of the boost pressure
regulator.
Compare readings with the values in the table below.
Pressure regulator valve. Connect the tool [1]on the valve (3).
Appy a pressure of 0.5 barto activate the rod "a":
Rod "a"should be moved 12 mm.
Engine speed (rpm) Pressure (Bar)
780 0,6
4000 0,25
B1HP12FD

Page 274 of 523

Downloaded from www.Manualslib.com manuals search engine 270
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: 8HX 8HW
Engines: 8HV 8HY
Tools.
[1]
Manual pressurevacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel
injection (HDi) engines.
EGR v
alve.Connect tool [1]on the capsule takeoff (2).
Apply a vacuum of approx.0,6 barseveral times to activate the rod «a».
In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
Regulation electrovalve (EGR).(Engine:8HX8HW).Check to be performed between the electrovalve (1)and the EGR valve (2).
Link the tool [1]in series, between the electrovalve (1)and the capsule (2).
Compare the values noted with those in the table below.
Regulation electrovalve (EGR).(Engine:8HV8HY).Check to be performed between the electrovalve (2)and the EGR valve (1).
Link the tool [1] in series, between the electrovalve (2)and the capsule (1).
Compare the values noted with those in the table below.
Engine speed (rpm) Vacuum value
780 0,5
2500 0
B1HP15GD
B1HP1K6D
C2 C3

Page 275 of 523

Downloaded from www.Manualslib.com manuals search engine 271
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: 9HZ 9HY
B1HP1UPC
B1HP1UQC
XSARA PICASSO
Exhaust gas recycling (EGR) valve.
(1)
Exhaust gas recycling (EGR) electrovalve
NOTE:The engine ECU pilots the EGR valve.
Perform the check with the aid of a diagnostic tool.
Carry out the following operations with the diagnostic tool:
«INJECTION» menu.
Actuator tests.
EGE electrovalve.
Check that you can hear the click from the EGR regulation electrovalve.
Double butterfly housing (vehicle with particle filter).
(2)
Double butterfly housing.
Perform the check with the aid of a diagnostic tool.
Carry out the following operations with the diagnostic tool:
«INJECTION» menu.
Actuator tests.
Butterfly.
EGR exchanger butterfly.
Check that you can hear the click from the double butterfly housing.

Page 276 of 523

Downloaded from www.Manualslib.com manuals search engine 272
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]
Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
EGR valve.
Connect the tool [1]to the capsule union (1).
Apply several times in succession a vacuum of approx.0.6 barto activate the rod "a".
In abrupt reaction to the vacuum, the valve should close on its seating with a clicking
noise.
Exhaust gas reycling (EGR) electrovalve. Check, not under load, between the electrovalve (2)and the EGR valve (1).
Connect the tool [1]between the electrovalve (2)and the capsule (1).
Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value
7800,5
25000
B1HP12GD

Page 279 of 523

Downloaded from www.Manualslib.com manuals search engine 275
INJECTION
SPECIAL FEATURES: FORCED REGENERATION OF THE PARTICLE FILTER
Tools.
Diagnostic stations: LEXIA or PROXIA
Imperative: Respect the safety and cleanliness requirements.
Forced regeneration of the particle filter.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
ESSENTIAL: Connect the vehicle to a gas extractor approved for this type of operation.In the absence of the required installations,carry out the forced regeneration of the particle filter outside the workshop, in a concreted
area well away from any inflammable materials. Place the vehicle in the high position.
WARNING:
Check that the fuel level is sufficient (at least 20 litres).
Start the engine and allow it to warm up (60°C minimum).
Connect the diagnostic tool to the vehicle’s central socket.
Trigger the regeneration cycle, with the diagnostic tool.
Automatic running of the regeneration cycle of the particle filter:
Autocheck by the engine ECU. Stabilisation of engine speed at
4000 rpm, operating with post injection.
Change to idling speed (for 30 seconds).
Stabilisation of engine speed at 3000 rpm, checking of the efficiency of the regeneration of the particle filter.
Change to idling speed.
NOTE:Let the engine run at idling speed for the benefit of cooling.
Stop the engine.
IMPERATIVE: Wait for at least an hour before any operation on the exhaust line.
ALL TYPES

Page 280 of 523

Downloaded from www.Manualslib.com manuals search engine 276
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / FILLING OF THE ADDITIVE RESERVOIR
Imperative: Respect the safety and cleanliness requirements.
Tools.
Filling kit comprising the following items:1Container of Eolys2Filters2Tubes1Empty container2Hooks1Adaptor
Filling.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves
that are resistant to hydrocarbons.
Place the vehicle on a lift.
Disconnect the battery negative terminal.
Unclip the the factory filler connector
(1).
Couple the container of additive to the tube (2)using the adaptor and the tube (with tap)from the
filling kit.
Screw the filler connector on the additive container
(3)at «b».
Place the additive container (3)on the component lift.
Open the tap located on the filler connector at «a».
Tilt the additive container (3)(to facilitate the end of filling).
Close the tap at «a».
Remove the filler connector and the tube (4).
Couple the tube (2).
Reconnect the battery negative terminal.
IMPERATIVE: The filling kit should be recycled after this operation. Any «Eolys» additive
containers that have been opened should not be kept.
XSARA PICASSO
B1HP1UVC
C4BP1EGC

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 61-70 next >