warning Citroen C3 2004 1.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine 402
AXLES
SUSPENSION
STEERING
A > B =Negative figure: – = TOEOUT
A < B = Positive figure:+ =TOEIN
WARNING
AXLE GEOMETRY
Checks at reference height (the reference height of the vehicle is set as per the table below).
NO CRD Vehicle (CRD = Difficult road conditions)
Front axle Rear axle
Vehicle Tracking Castor Pivot angle Camber Tracking Camber
Adjustable Yes No
All types0 ± 1 mm4,8 ± 1,3 mm
0°09’ at + 0°09’3° ± 18’ 10°43’ ± 30’ 0° ± 30’
0°43’ ± 0°12’ 1°13’ ± 18’
XSARA PICASSO
B3CP02UC

Downloaded from www.Manualslib.com manuals search engine 404
AXLES
SUSPENSION
STEERING
A > B =Negative figure: – = TOEOUT
A < B = Positive figure:+ =TOEIN
WARNING
AXLE GEOMETRY
Checks at reference height (the reference height of the vehicle is set as per the table below).
CRD Vehicle (CRD = Difficult road conditions)
Front axle Rear axle
Vehicle Tracking Castor Pivot angle Camber Tracking Camber
Adjustable Yes No
All types 1 ± 1 mm3,7 ± 1,3 mm
0°18’ at 0°0’2°56’ ± 18’ 10°25’ ± 30’ 0°07’ ± 30’
0°33’ ± 0°12’ 1°14’ ± 18’
XSARA PICASSO
B3CP02UC
Engines: NFV RFN RHY

Downloaded from www.Manualslib.com manuals search engine 419
BRAKES
C5FP0ELD
HANDBRAKE (Adjustment)
Adjustment.
Lift and chock the vehicle.
Remove:
The rear cover
(8).
The nut (9).
The handbrake trim (6).
The gear lever gaiter (5).
The front cover (3).
The screws (1).
Disconnect the connectors of the following components:
The cigar lighter
(2).
The electric window buttons (4).
Remove the central console
(7).
WARNING:Check that the brake cables are correctly
routed under the vehicle.
Slacken the handbrake lever.
Press gently on the brake pedal
(Then repeat the ope
ration 3 times).
Pull vigorously on the handbrake lever 4 or 5 times.
C2

Downloaded from www.Manualslib.com manuals search engine 421
BRAKES
B3FP15XC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]
Generic bleeding apparatus :«LURO»Bleeding, refilling.
Draining.
Drain the brake fluid reservoir (1)to the maximum(if necessary, use a clean syringe).
Disconnect the connector (4).
Uncouple the pipe (2).
Unscrew the shaft (3).
Remove the reservoir (1).
Empty the brake fluid reservoir (1).
Clean the brake fluid reservoir (1).
Refit:
The brake fluid reservoir
(1).
The shaft (3).
Couple the pipe (2).
Reconnect the connector (4).
Filling the braking system.WARNING:Use only those hydraulic fluids that are approved and recommended.
Fill the brake fluid reservoir (1).
Bleeding the braking system.WARNING:During the bleeding operation, take care to maintain the level of brake fluid in the reservoir
and to top it up, using only brake fluid that is clean and clear.
C2

Downloaded from www.Manualslib.com manuals search engine 422
BRAKES
B3FP15YCB3FP15ZD
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
Bleeding the primary braking circuit.
WARNING:The ABS should not be active during the
bleeding operation.
Front brake caliper, Bleed screw
(5).A: Rear brake caliperB: Rear brake drum
Bleed screw
(6).
Bleed each wheel cylinder, proceeding in the following
order:
Front LH wheel.
Front RH wheel.Rear LH wheel.
Rear RH wheel.
C2

Downloaded from www.Manualslib.com manuals search engine 433
BRAKES
BRAKE SPECIFICATIONS
Evolution: rear wheel cylinder (applies from RPO 9667)
C3 C3 Pluriel
Evolution.
New wheel cylinders at the rear, with cutoff pressure 27 bars instead of 35 bars.
Assembly.
(1)
Rear wheel cylinder.
Repair.
IMPERATIVE:The mixing of the old and new components is STRICTLY FORBIDDEN.
WARNING:
Identify the type of assembly prior to starting a repair.
ESSENTIAL: Systematically replace the wheel cylinders on both sides on the same axle.
Replacement parts.
Replacement Parts will market only the components for the new assembly.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 434
BRAKES
C5FP0ELD
HANDBRAKE (Adjustment)
Adjustment.
Lift and chock the vehicle.
Remove:
The rear cover
(8).
The nut (9).
The handbrake trim (6).
The gear lever gaiter (5).
The front cover (3).
The screws (1).
Disconnect the connectors of the following components:
The cigar lighter
(2).
The electric window buttons (4).
Remove the central console (7).
WARNING:Check that the brake cables are correctly
routed under the vehicle.
Slacken the handbrake lever.
Press gently on the brake pedal
(Then repeat the operation3 times).
Pull vigorously on the handbrake lever 4 or 5 times.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 436
BRAKES
B3FP15XC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]
Generic bleeding apparatus: «LURO» or similar.
Bleeding,refilling.
Draining.
Drain the brake fluid reservoir (1)to the maximum (if necessary, use a clean syringe).
Disconnect the connector (4).
Uncouple the pipe (2).
Unscrew the shaft (3).
Remove the reservoir (1).
Empty the brake fluid reservoir (1).
Clean the brake fluid reservoir (1).
Refit:
The brake fluid reservoir
(1).
The shaft (3).
Couple the pipe (2).
Reconnect the connector (4).
Filling the braking system.WARNING:Use only those hydraulic fluids that are approved and recommended.
Fill the brake fluid reservoir (1).
Bleeding the braking system.WARNING:During the bleeding operation, take care to maintain the level of brake fluid in the reser
voir and to top it up, using only brake fluid that is clean and clear.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 437
BRAKES
B3FP15YCB3FP15ZD
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
Bleeding the primary braking circuit.
WARNING:The ABS should not be active during the
bleeding operation.
Front brake caliper, Bleed screw
(5).A: Rear brake caliperB: Rear brake drum
Bleed screw
(6).
Bleed each wheel cylinder, proceeding in the following
order:
Front LH wheel.
Front RH wheel.
Rear LH wheel.
Rear RH wheel
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 449
BRAKES
BRAKE SPECIFICATIONS
Gyrometer sensor
(7) Hydraulic b lock
C4AP17YCB3HP002C
Observations
P art no.
Supplier
Components
XSARA
ESP
hydraulic blockBOSCH 5.7 ESPLocated on the front LH
wheelarch:4adjustment channels.
IMPERATIVE:Respect the direction of fitting of the gyrometer/accelero
meter sensor (connector towards the rear of the vehicle).
WARNING:The gyrometer/accelerometer sensor should not be subjected to any impact.Any gyrometer/accelerometer sensor havingsuffered an impact must be replaced.Tightening torque (15):0,6 ± 0,1 m.daN.