ADJUST IDLE SPEED Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 252
INJECTION
SPECIFICATIONS OF THE DELPHI DIESEL INJECTION PUMP XSARA
Engine
typePump
Type
ReferenceStatic timing
Initial advance
Compression
Time
(cylinder N° 4)Dynamic
timing
checking
(at idle)Reference
InjectorInjector
holder
+ injectorCode
colourInjector
needle lift
pressure
(Bar)Adjustments (rpm) Max. speed
Fast
idlingAntistall
IdlingUnladen
rpmLaden
rpm
WJYDWLP 12
R 8448 B/*RDNO
SDC
6903LDCR
0260
IAA135,5
±5950
±25875
±25875
±255350
± 125
Engine
TDC
Pegging hole.
Value «X»
engraved on
the pump.
(*) = See table page: 251.1500
+ 3
mm
shim

Downloaded from www.Manualslib.com manuals search engine 256
INJECTION
ADJUSTING THE MECHANICAL CONTROLS OF THE DELPHI INJECTION PUMP
Engine: WJY (continued)
Adjusting the antistall (residual output).
Insert a 3 mmthick shim (10)between the throttle lever (6)and the antistall screw (7).
Push the stop lever (8).
Insert a 3 mmdiameter peg (9)in the lever (2).
Adjust the engine speed to 1500 rpm ± 100using the stop screw (7).
Remove the shim (10)and the peg (9).
Adjusting the idle speed.
Adjust the speed using the idle adjustment screw (11).
Idling speed:825 ± 25 rpm.
Checking the engine deceleration.
Move the throttle lever (6)to obtain an engine speed of 3000 rpm.
Release the throttle lever (6).
The deceleration should be between 2.5and 3.5seconds.
The drop should be approximately 50 rpmin relation to the idle speed.
Deceleration too fast, (the engine has a tendency to stall)slacken the screw (7)by a quarter turn.
Deceleration too slow, (engine speed is greater than the idle speed)tighten screw (7)by a quarter turn.
NOTE:In each case, check the idle speed for any necessary adjustments.
B1HP0K9CB1HP0KAC
XSARA

Downloaded from www.Manualslib.com manuals search engine 319
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX
Engines: NFV 6FZ RFN RFS 8HV 8HY 9HZ 9HY WJY RHY RHZ
Description
(1)
Primary shaft.
(2)Clutch bearing guide.
(3)Gearbox casing.
(4)Clutch housing.
(5)Reverse idle.
(6)Drive gear (3rd gear).
(7)3rd / 4th gear synchroniser.
(8)Drive gear (4th gear).
(9)Drive gear (5th gear).
(10)5th gear synchroniser.
(11)Driven gear (5th gear).
(12)Driven gear (2nd / 4th gear).
(13) Driven gear (2nd gear).
(14)1st / 2nd gear synchroniser.
(15)Driven gear (1st gear).
(16)Secondary shaft.
(17)Differential gear.
(18)Satellite gears.
(19)Planet gears.
(20)Differential housing.
(21)Speedometer drive.
(22)Extension.
«d» Adjusting shims: 0.7 to 2.4 mm
(0.10 mm and increasing by 0.10 mm).
«c»Adjusting shims:1.4 to 1.6 mm
(0.10 mm and increasing by 0.10 mm).
B2CP3BQP
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 498
AIRCONAIRCON
AIR CONDITIONING SYSTEM R 134.a
Testing procedure
Conditions inside the vehicle.
Positions of the air conditioning controls:
Maximum cold.
Maximum blower power.
Air distribution on
«ventilation»with the air vents open.
Position the air inlet flap to outside air.
WARNING:For RFTA (1), disconnect the air inlet motor connector, first
ensuring that it is in the outside air position.
(1) RFTA= Fully automatic air conditioning.
Test procedure.When all these conditions are met, proceed in the following order:
Measure the temperature in the workshop approx. one metre in front of
the vehicle’s air inlet grille.
Start the engine
(without the air conditioning, or the blower, operating)and wait for the cooling fan slow speed to trigger (should the engine tem
perature not rise sufficiently, it is permissable to increase the engine
speed to 2000 rpm)
.
Once it is sufficiently hot in the engine compartment, return the engine
to idle and commence the test.Switch on the air conditioning and adjust the engine speed to
2500 rpm.
In an ambient temperature of 40°C, the engine speed will be brought
down to 2000 rpm, in order for the pressure safety threshold to cut off the
compressor.
For further temperatures/pressures: see Tables and Graphs on following
pages
221, 222 and 226.
After
3 minutesof operation, note down the following 3 parameters:
The temperature of the blown air coming out of the 2 central air vents
(take the average).
The high pressure, via the intermediary of the clickfit union (at the
pressure reducer inlet).
The low pressure, via the intermediary of the clickfit union (at the pressure
reducer outlet).NOTE:The low and high pressures are absolute pressures.
When measuring the blown air temperatures, avoid any contact between
the thermocouple and the air vents.
At the conclusion of the test involving vehicles with
«RFTA»
ALL TYPES