Fluid Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 58
GENERAL
LUBRICANTS TOTAL recommended oils
GEARBOX OILS
ALL TYPES
TOTAL TRANSMISSION BV
norms S.A.E.: 75W80
Part No.: 9730 A2.
TOTAL FLUIDE ATX
TOTAL FLUIDE AT 42
Special oil distributed by
CITROËN
Part No.: 9730 A3
Special oil distributed by
CITROËN
Part No.: 9736 22
TOTAL TRANSMISSION X4Part No.:9730 A4
Manual gearbox and SensoDrive
MB3 automatic gearbox
4HP20 and AL4 autoactive
automatic gearboxes
Transfer box and rear axle
All countries

Downloaded from www.Manualslib.com manuals search engine 59
GENERAL
LUBRICANTS TOTAL recommended oils
POWER STEERING OILS
ENGINE COOLANT FLUID
ALL TYPES
TOTAL FLUIDE ATX
TOTAL FLUIDE DAS
Special oil distributed by
CITROËN
Part No.: 9730 A1
Power steering
All countries
Very cold countries
All countriesCITROËN fluid
Protection: 35C°
2Litres
5Litres
20 Litres
210Litres
9979 70
9979 71
9979 769979 779979 72
9979 73
9979 749979 75 PackCITROËN Part No.
REVKOGEL 2000
GL YSANTIN G33

Downloaded from www.Manualslib.com manuals search engine 60
GENERAL
LUBRICANTS TOTAL recommended oils
BRAKE FLUIDS
Synthetic brake fluid
HYDRAULIC CIRCUIT
WARNING: TOTAL FLUIDE LDS fluid cannot be blended with TOTAL LHM.
WARNING: CITROËN C5: Use exclusively TOTAL FLUIDE LDS suspension fluid.
All countriesTOTAL HYDRAURINCAGE
All countriesCITROËN fluid
0,5Litre
1 Litre
5 Litres
9979 05
9979 069979 07 Pack
CITROËN Part No.
ALL TYPES
Pack
CITROËN Part No.
Norm
Colour
All countries
TOTAL FLUIDE LDS
TOTAL LHM PLUS
TOTAL LHM PLUS
Very cold countries Orange 9979 69
ZCP 830095
9979 20 Green1
Litre

Downloaded from www.Manualslib.com manuals search engine 61
GENERAL
SCREEN WASH FLUID
GREASE
General use
All countriesConcentrated:
250ml
Fluid ready
for use9980 33
9980 06
9980 05ZC 9875 953U
ZC 9875 784U
ZC 9885 077U9980 56
ZC 9875 279U Pack
CITROËN Part No.
LUBRICANTS TOTAL recommended oilsALL TYPES
1Litre
5Litres
Norms NLGI
2
TOTAL MULTIS 2
TOTAL SMALL MECHANISMS
All countries
Note:NLGI = National Lubricating Grease Institute.

Downloaded from www.Manualslib.com manuals search engine 198
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18WD
Setting the timing (continued).
Chec
king the setting.
IMPERATIVE: Just prior to refitting, carry out the following tests.
Check that:
the rollers and the coolant pump operate freely
(no play and no tight spot).
there are no traces of oil
(from the crankshaft and camshaft sealing rings).
there is no leak of coolant fluid
(from the coolant pump).
the target track of the engine speed sensor
(14)is not damaged or scratched
(if necessary replace the defective components).
Refitting.
Fit the timing belt on the crankshaft pinion.
Position the belt on the guide roller, with the belt well tensioned.
Refit:
The timing protector
(13).
The sensor
(14).
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
201
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple: The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.
Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pretighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to 5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
The tube (2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splashshield
(see corresponding operation).
The front RH wheel, tighten to 9 ±1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE:Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).

Downloaded from www.Manualslib.com manuals search engine 205
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple:
The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 207
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1EP1E6D
Refit the screw (10).
Turn the crankshaft to bring the camshaft towards its pegging point.
Peg the camshaft at
«c», using tool [2](oil the pegs).WARNING: Do not press or damage the track of the engine speed sensor target
(13).
Peg the crankshaft at «e», using tool [3].
Remove:
The timing belt protector
(13).
The engine speed sensor (14).
Slacken the screw (15)of the tensioner roller, and keep it slackened using an allen
spanner at «d».
Detension the timing belt by pivoting the tensioner roller (clockwise).
Remove the timing belt, starting with the coolant pump pinion.
Checks.
ESSENTIAL: Just prior to refitting, proceed to the checks as below.
Check:
That the rollers and the coolant pump pulley turn freely (without play and without tight
spot).
That there are no signs of oil leaks (at the crankshaft and camshaft seals).
That there are no leaks of coolant fluid(at the coolant pump).
That the track of the engine speed sensor target (15)is not damaged or scratched.
Replace any components that are defective (if necessary).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting (continued).
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pretighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Disengage the jack from under the engine.
Couple:
The tube
(2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splashshield (see corresponding operation).
The front RH wheel, tighten to 9 ± 1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE: Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).