Sump Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 30
GENERAL
CAPACITIES (in litres)
Draining mandhod.
The oil capacities are defined according to the following mandhods.
1/
Vehicle on level surface (in high position, if equipped with hydropneumatic suspension).
2/Engine warm (oil temperature 80°C).
3/ Draining of the oil sump + removal of the cartridge (duration of draining + dripping = 15 min).
4/Refit plug + cartridge.
5/ Engine filling.
6/Engine starting (allowing the cartridge to be filled).
7/ Engine stopped (stationary for 5 min).
ESSENTIAL: Systematically check the oil level using the oil dipstick.

Downloaded from www.Manualslib.com manuals search engine 40
GENERAL
ALL TYPES
LUBRICANTS TOTAL recommended oils
S.A.E. Norms Table for selection of engine oil gradeSelection of engine oil grades recommended for climatic conditions in corntries of distribution.Evolution of the norms as at 01/01/2003
ACEA 2003 norms
The meaning of the first landter has not changed, it still corresponds
to the type of engine:
A:petrol and dual fuel petrol / LPG engines.B: dieselengines.
The figure following the first landter corresponds to the type of oil:
3:high performance oils.4:oils specifically for direct injection diesel engines.5:very high performance oils permitting lower fuel consumption.Example:
ACEA A3:high performance oils specifically for petrol and dual fuel
petrol / LPG engines.
ACEA A/B:blended oils giving very high performance for all engines,
also permitting bandter fuel economy, specifically for direct injection dieselengines
NOTE:From 01/01/2003there is no longer any reference to the year
of creation of the norm (example:ACEA A3/B3 98becomes ACEAA3/B3).
API norms
The meaning of the first landter has not changed, it still corresponds to
the type of engine:
S: petrol and dual fuel petrol / LPGengines.C: dieselengines.
The second landter corresponds to the degree of evolution of the oil
(ascending order).
Example:Norm SLis more severe than norm SJ, corresponding to a
higher level of performance.

Downloaded from www.Manualslib.com manuals search engine 62
GENERAL
ENGINE OIL CONSUMPTION
I Oil consumption depends on:
the engine type.
how runin or worn it is. the type of oil used.
the driving conditions.
II An engine can be considered
RUNINafter:

3,000 miles (5,000 km)for a PETROLengine.
6,000 miles (10,000 km)for a DIESELengine.
III
MAXIMUM PERMISSIBLEoil consumption for a RUNINengine:
0.5 litresper 600 miles (1,000 km)for a PETROLengine. 1 litreper 600 miles (1,000 km)for a DIESELengine.DO NOT INTERVENE BELOW THESE VALUES.
IV OIL LEVEL:The level should NEVER be above the MAX. markon the dipstick after changing or topping up the oil.
This excess oil will be used up rapidly.
It will reduce the engine output and adversely affect the operation of the air circuits and gas recycling
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 68
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
EnginesHFX KFV NFU
Crankshaft
Accessories drive pulley2,5 ± 0,2
Pinion fixing on crankshaft
Tightening4 ± 0,4
Angular tightening45° ± 4°
Cylinder block
Sump0,8 ± 0,2
Timing belt tensioner roller2,1 ± 0,2
Accessories belt guide roller2,5 ± 0,2
Alternator support2,5 ±0,2
Alternator TU1JPTU3JP
Pretightening
1 ±
Tightening3,7 ± 0,3
Alternator TU5JP4
Pretightening
1 ±
Tightening4 ±,04
Aircon compressor support 2,2 ± 0,2
Aircon compressor2,3 ± 0,2
C2

Downloaded from www.Manualslib.com manuals search engine 72
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engine8HX
Crankshaft
Bearing cap fixing screws
Pretightening
1 ± 0,2
Slackening180°
Tightening3 ± 0,3
Angular tightening140°
Con rod screws
Tightening
1 ± 0,1
Angular tightening100° ± 5°
3 ± 0,3
Angular tightening180° ± 5°
Cylinder block
Sump1,3 ±0,1
Timing belt guide roller2,3 ± 0,2
Timing belt tensioner roller3,7 ± 0,3
C2

Downloaded from www.Manualslib.com manuals search engine 76
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Crankshaft
Engine types HFX KFV NFU
Accessories drive pulley0,8 ± 0,2
Pinion fixing on crankshaft10 ± 1 2,5 ± 0,2
Cylinder block
Sump0,8 ± 0,2
Timing belt tensioner roller2 ± 0,2 2,2 ± 0,2
Accessories belt tensioner roller2 ± 0,2 2,5 ± 0,2
Alternator support fixing1,7 ±0,3
Alternator fixing on support3,7 ± 0,3
Cylinder head
Coolant outlet housing0,8 ± 0,2
Camshaft bearing cap
Tightening
2 ± 0,2 2 ± 0,2
Angular tightening44°±4°50° ± 5°
0,8 ± 0,2
Exhaust manifold1,7 ± 0,3 2 ± 0,2
Valve rockers adjusting screw1,75 ±0,25
Sparking plugs2,75 ± 0,25
Camshaft pulley screw8 ± 0,8
C3

Downloaded from www.Manualslib.com manuals search engine 79
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
EngineKFU
Crankshaft
Accessories drive pulley0,8 ± 0,2
Pinion fixing on crankshaft
Pretightening
4 ± 0,4
Angular tightening45 ± 4°
Cylinder block
Sump0,8 ± 0,2
Accessories belt guide roller4 ± 0,4
Timing belt tensioner roller2,1 ± 0,2
Accessories belt tensioner roller2,5 ± 0,2
Alternator support2,5 ± 0,3
Crankshaft bearing caps
Tightening
2 ±0,3
Angular tightening44°(reused screws cleaned and greased)
Cylinder head
Coolant outlet housing0,8 ± 0,2
Camshaft bearing caps1 ± 0,2
Camshaft bearing cap covers0,9 ± 0,1
Inlet manifold0,8 ± 0,2
C3

Downloaded from www.Manualslib.com manuals search engine 83
ENGINE
83
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines 8HX 8HW 8HZ
Crankshaft
Bearing cap fixing screw
Pretightening1
SlackeningYES
Tightening3
Angular tightening140°
Con rod nuts
Pretightening1
SlackeningYES
Tightening1,5 ± 0,1
Angular tightening100°±5°
Accessories drive pulley
Pretightening3 ±0,4
Angular tightening180°±5°
Cylinder block
Sump1 ± 0,1
Timing belt guide roller 4,5 ± 0,4 3,7 ± 0,4Timing belt tensioner roller3 ± 0,3 2,3 ± 0,3
C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 87
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines8HV 8HY
Crankshaft
Bearing cap fixing screw
Tightening3 ± 0,3
Angular tightening140° ± 1°,4’
Crankshaft pullet hub
Angular tightening180°±5°
Cylinder block
Oil sump1 ±0,1
Timing belt tensioner roller 4 ± 0,4
Timing belt guide roller
2,5 ±0,2
Timing belt guide roller support
Cylinder head
Camshaft bearing cap cover
1 ±0,1
Inlet manifold
Exhaust manifold2,5 ± 0,2
Cylinder head cover Screws (M6) to 1 ± 0,2
Camshaft pinion4,3 ± 0,4
Fuel high pressure pump pinion 5 ± 0,5
C3

Downloaded from www.Manualslib.com manuals search engine 92
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines9HZ 9HY
Crankshaft
Bearing cap fixing screw
Pretightening1 ± 0,2
Slackening180°
Tightening3 ± 0,3
Angular tightening140°
Con rod screws
Tightening1 ±0,1
Angular tightening100 ±5°
Accessories drive pulley
Pretightening3,5 ± 0,4
Angular tightening190 ± 5°
Cylinder block
Sump 1,3 ± 0,1
Timing belt guide roller3,7 ± 0,3
Timing belt tensioner roller2,7 ± 0,2
XSARA PICASSO