change Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 31
C2
CAP ACITIES (in litres)
GENERAL
HFX KFV NFU 8HX RPO 9884 8HX RPO 9885
3 3,25 3,75
1,51,81,5
2
2
±0,15
0,7 Litre version with front calipers Ø 48 / rear drums
0,8 Litre version with front calipers Ø 54 / rear discs
75,6
40 45
Diesel
P etrolC2
1.1i 1.4i 1.6i 16V 1.4 HDi
ESSENTIAL: Systematically check the oil level using the oil dipstick.
Engine type
Drain by gravity: engine
with filter change
Bandween min. and max.
MA5 5speed gearbox
MA5 piloted 5speed gearbox
Braking circuit
Cooling system
Fuel tank capacity

Downloaded from www.Manualslib.com manuals search engine 32
GENERALEngine type
Drain b
y gravity: enginewith filter changeBandween min. and max.
Drain by suction: enginewith filter changeBandween min. and max.5speed gearboxAutomatic gearboxAfter oil change
Braking circuit
Cooling system
Fuel tank capacity
RPO 9884 RPO 9885 RPO 9884 RPO 9885
HFXKFV KFU NFU 8HX 8HW 8HX 8HW 8HV 8HY 8HV 8HY
33,753,253,75
1,5 1,2 1,5 1,8 1,5 1,8 1,5
3,1 3,1
1,5 1
221,9
0,7 Litreversion with front calipers Ø 48 / rear drums
0,8 Litreversion with front calipers Ø 54 / rear discs
7 7 5,7 5,6
45
C3 CAPACITIES (in litres)
Diesel
P etrolC3
1.1i
1.4i
1.4i
16V1.4 HDI 16V
ESSENTIAL:systematically check the oil level using the oil dipstick.
(1)= The gearbox is lubricated for life. (For yorr information, the TOTAL capacity is 5,85 litres, after draining:3 litres).
AUTO.
1.4 HDi1.6i
16V
(1)

Downloaded from www.Manualslib.com manuals search engine 33
GENERAL
1.4i 1.6i 16V 1.4 HDi
Engine type KFV NFU 8HX
Drain b
y gravity: engine with filter change 3 3,25 3,75
Bandween min. and max. 1,5 1,5 1,55speed gearbox2
Braking circuit0,7 Litre
version with front calipers Ø 48 / rear drums
0,8 Litre
version with front calipers Ø 54 / rear discs
Cooling system 7 5,7
Fuel tank capacity45
ESSENTIAL: systematicall
y check the oil level using the oil dipstick.
(1)= The gearbox is lubricated for life.(For yorr information, the TOTAL capacity is 5,85 litres, after draining : 3 litres)
CAPACITIES (in litres)
PetrolC3 Pluriel
Diesel
C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 40
GENERAL
ALL TYPES
LUBRICANTS TOTAL recommended oils
S.A.E. Norms Table for selection of engine oil gradeSelection of engine oil grades recommended for climatic conditions in corntries of distribution.Evolution of the norms as at 01/01/2003
ACEA 2003 norms
The meaning of the first landter has not changed, it still corresponds
to the type of engine:
A:petrol and dual fuel petrol / LPG engines.B: dieselengines.
The figure following the first landter corresponds to the type of oil:
3:high performance oils.4:oils specifically for direct injection diesel engines.5:very high performance oils permitting lower fuel consumption.Example:
ACEA A3:high performance oils specifically for petrol and dual fuel
petrol / LPG engines.
ACEA A/B:blended oils giving very high performance for all engines,
also permitting bandter fuel economy, specifically for direct injection dieselengines
NOTE:From 01/01/2003there is no longer any reference to the year
of creation of the norm (example:ACEA A3/B3 98becomes ACEAA3/B3).
API norms
The meaning of the first landter has not changed, it still corresponds to
the type of engine:
S: petrol and dual fuel petrol / LPGengines.C: dieselengines.
The second landter corresponds to the degree of evolution of the oil
(ascending order).
Example:Norm SLis more severe than norm SJ, corresponding to a
higher level of performance.

Downloaded from www.Manualslib.com manuals search engine 74
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engine8HX
Lubrication circuit
Oil pump assembly
Pretightening
0,5 ± 0,1
Tightening0,9 ± 0,1
Coolant/oil heat exchanger1 ± 0,1
Diesel injection circuit
Sphericalbase screws for diesel injection fixing fork2,5 ± 0,2
Fuel high pressure common injection rail on engine block2,2 ± 0,2
Unions on fuel high pressure common injection rail2,5 ± 0,2
Diesel injection pump on support2,2 ± 0,2
Union on diesel injection2,5 ±0,2
Diesel injection pump pulley5 ± 0,5
Union on diesel high pressure pump2,5 ± 0,2
Cooling circuit
Coolant pump
Pretightening
0,3 ±0,1
Tightening0,9 ± 0,1
Coolant outlet housing
Pretightening
0,3 ±0,1
Tightening0,7 ± 0,1
C2

Downloaded from www.Manualslib.com manuals search engine 84
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines 8HX 8HW 8HZ
Cylinder head
Camshaft bearing covers
Pretightening0,5 ±
Tightening1 ±
Fixings of camshaft subassemblies on cylinder head
Pretightening0,5
Tightening1
Exhaust manifold2,5 ± 0,2
Valve cover2,5 ± 0,2
Camshaft pulley4,3 ±0,4
Flywheel
Flywheel
Pretightening1,7 1,7
Tightening70°±5° 75° ± 5°
Clutch mechanism 2 ± 0,2
Lubrication circuit
Oil pump assembly
Pretightening0,5 ± 0,06
Tightening0,9 ± 0,1
Coolant/oil heat exchanger1 ± 0,1
C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 88
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines8HV 8HY
Flywheel Clutch
Flywheel 1,7 ± 0,2
Clutch mechanism 2 ± 0,2
Lubrication circuit
Oil pump assembly0,9 ± 0,1
Oil/coolant heat exchanger 1 ± 0,1
Turbocharger lubrication pipe2,2 ± 0,2
Injection circuit
Injector fixing flange nut
Tightening0,4 ±0,1
Angular tightening65° ± 5°
Fuel high pressure pump
Union on diesel injector
Fuel high pressure pump pinion 5 ± 0,5
Union on fuel high pressure pump2,3 ± 0,2
Cooling circuit
Coolant pump1 ± 0,2±
C3

Downloaded from www.Manualslib.com manuals search engine 94
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines9HZ 9HY
Lubrication circuit
Oil pump assembly
Pretightening0,5 ± 0,1
Tightening0,9 ± 0,1
Oil/coolant heat exchanger 1 ± 0,2
Turbocharger lubrication pipe3 ± 0,5
Diesel injection circuit
Injector fixing flange nut
Pretightening4 ± 0,1
Angular tightening65° ± 5°
Fuel high pressure common injection rail on engine block 2,2 ± 0,2Union on fuel high pressure common injection rail
Pretightening1,7 ±0,2
Tightening2,2 ±0,2
Diesel injection pump on support2,2 ± 0,2
Union on diesel injector
Pretightening2 ± 0,5
Tightening2,5 ±0,3
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 135
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
With compressor and alternator .
B1BP2MKCB1BP2MJD
Tools.
[1]
Pliers for removing plastic pegs: 7504T
[2]Tensioner roller compression lever:().0194.E
[3]Tensioner roller setting peg Ø4 mm: ().0194.F
Removing.
Disconnect the battery negative cable.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel.
Move aside the splashshield, using tool
[1].
IMPERATIVE: In the case of belt reuse, mark the
direction of rotation of the belt. If the index on the
tensioner roller is outside the marks, change
the auxiliary equipment drive belt.
The alternator (1).
The aircon compressor (2).
Detension the auxiliary belt tensioner roller, using tool [2].
Position the peg [3].
Remove the auxiliary drive belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1BP2N0C
Tools.
[1]
Engine flywheel peg Ø 12 mm : ().0194C
[2]
Camshaft pulley peg Ø 8 mm : ().0194B
[3]
Crankshaft pulley peg Ø 5 mm : ().0194A
Preliminar
y operations.
Remove:
The front RH wheel.
The front RH splashshield.
The accessories belt
(see corresponding operation).
Uncouple:
The supply unions
(1).
The air/air heat exchanger inlet/outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connector
(2).
Support the engine by means of a roller jack equipped with a chock.
Remove the engine supports
(4) and(5).
C3