temperature Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 5
C2
OPERA TIONS TO BE CARRIED ORT AFTER A REPAIR
GENERAL
Sun roof.The antipinch function has to be reinitialised.
Place the sun roof switch in the maximum tilt position.
Keep the sun roof switch pressed until the sun roof ceases its movement.
Release the sun roof switch within 5 seconds.
Keep the sun roof switch pressed until the end of the sun roof opening sequence.
Multifunction screen.It is necessary to adjust the date, time and ortside temperature.
Adjust the display language of the multifunction screen if necessary.
NOTE:The default display language of the multifunction screen is French.
Navigation.Warning, the vehicle has to be in the open air (on switching on the ignition, the ECU searches for satellites).
Vehicle location is only effective after some ten minutes.Reprogramme the customer paramanders.
Radio.Reprogramme the radio stations.
Radiotelephone RT3.Reprogramme the radio stations.

Downloaded from www.Manualslib.com manuals search engine 30
GENERAL
CAPACITIES (in litres)
Draining mandhod.
The oil capacities are defined according to the following mandhods.
1/
Vehicle on level surface (in high position, if equipped with hydropneumatic suspension).
2/Engine warm (oil temperature 80°C).
3/ Draining of the oil sump + removal of the cartridge (duration of draining + dripping = 15 min).
4/Refit plug + cartridge.
5/ Engine filling.
6/Engine starting (allowing the cartridge to be filled).
7/ Engine stopped (stationary for 5 min).
ESSENTIAL: Systematically check the oil level using the oil dipstick.

Downloaded from www.Manualslib.com manuals search engine ENGINE
227
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
Plaque engine XFX KFV NFU 8HX
Temperature (°C) 90°C
Pressure (Bars) 3 4 1,3 3,5
Rpm 2000 4000 1000 4000
Tools (Kit 4103T)
2279T.Bis X X X X
4103T.B X X X X
7001T X X X1503.JX
C3 C3 Pluriel
Plaque engineHFXKFVKFUNFU8HX8HW8HV 8HY
Temperature (°C) 90°C
Pressure (Bars) 3 4 1,3 3,5
Rpm 2000 4000 1000 4000
Tools (Kit 4103T)
2279T.Bis X X X X X X X X
4103T.B X X X X X X X X
7001T X X X X
1503.JXX XX
NOTE:The oil pressure
should be checked with the
engine hot, after the oil level
has been checked.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 228
ENGINECHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA
Plaque engine KFW NFU RFN RFS 8HZ WJY RHY RHZ
Temperature (°C) 90°C 80°C 90°C
Pressure (Bars) 3 4 1,5 5,1 2 5,5 1,3 3,5 1,8 4,5 2 4
Rpm 2000 4000 1000 4000 1000 4000 1000 4000 1000 4000 1000 4000
Tools (Kit 4103T)
2279T.BisXXXXXX XX
4103T.B X X X X X X X X
7001T X
4202T X X X
5709T.B2 X
1503JX
4156TX
7017T.X23X
NOTE:
The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA

Downloaded from www.Manualslib.com manuals search engine 229
ENGINE
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA PICASSO
Plaque engine NFV 6FZ RFN 9HZ 9HY RHY
Temperature (°C) 90°C 80°C 90°C
Pressure (Bars) 3 4 3,3 6,3 1,5 5 1,3 3,5 2 4
Rpm 2000 4000 1000 4000 1000 3000 1000 4000 1000 4000
Tools (Kit 4103T)
2279T.Bis X X X X X X
4103T.B X X X X X X
7001T X
4202T X X X
1503JXX
NOTE:
The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 233
INJECTION
Emission standard Engine type
Injection make
and type
PETROL INJECTION
Air temperature sensor
resistive value (ohms)
C2
M. MARELLI 48P2 SAGEM S2000 BOSCH M.7.4.4.
Fuel pressure (bars)
Overspeed cutoff (rpm)
Injector resistive value (ohms)
Engine coolant temperature
sensor resistive value (ohms)
Idling actuator or stepper
motor resistive value (ohms)
HFX KFV NFU
L4/IFL5 L4/IFL5 IFL5
1.1i 1.4i 1.6i 16V
333
5500 5500 6600
14,5 12,2 14,5
Stepper motor: 53 3 800 at 10°C 2500 at 20° C 800 at 50°C 230 at 90° C
3 800 at 10°C 2500 at 20° C 800 at 50°C 230 at 90° C
C2

Downloaded from www.Manualslib.com manuals search engine 234
INJECTION
Emission standard Engine type
Injection make
and type
PETROL INJECTION
C3 C3 PLURIEL
Air temperature sensor
resistive value (ohms)
C3 PLURIEL
C3
M. MARELLI
48P2M. MARELLI
6LP SAGEM
S2000BOSCH
M.7.4.4.SAGEM
S2000BOSCH
M.7.4.4.
Fuel pressure (bars)
Overspeed cutoff (rpm)
Injector resistive value (ohms)
Engine coolant temperature
sensor resistive value (ohms)
Idling actuator or stepper
motor resistive value (ohms)
HFX
K’L4INFL4/IFL5 L5 K’L4INFL4/IFL5 L4 L4/IFL5 IFL5
1.1i 1.4i 1.4i 16V 1.6i 16V
1.6i 16V
1.4i
KFU
KFV NFU KFV NFU
3,53,5
3,5
3,5 3,5 3,5
14,5 14,5 14,5
12,214,5 14,5
5500
5800
5500
5500
5500 5800
Stepper motor:53 3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C
3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C

Downloaded from www.Manualslib.com manuals search engine 235
INJECTION
Emission standard Engine type
Injection make
and type
PETROL INJECTION
XSARA XSARA PICASSO
Air temperature sensor
resistive value (ohms)
XSARA PICASSO
XSARA 2
SAGEM
S2000M. MARELLI
6LP BOSCH
M.7.4.4.BOSCH
M.7.4.4.SAGEM
S2000M. MARELLI
6LP
Fuel pressure (bars)
Overspeed cutoff (rpm)
Injector resistive value (ohms)
Engine coolant temperature
sensor resistive value (ohms)
Idling actuator or stepper
motor resistive value (ohms)
KFW
L4/IFL5/L5 L4/IFL5 L4/IFL5 L4 IFL5L4/IFL5
1.4i 1.6i 16V 2.0i 16V 1.6i
2.0i 16V
1.8i 16V
RFN
NFU NFV 6FZ RFN
3,53,5
3
3 3,5 3,5
14,5 14,5 14,5
14,512,2 14,5
5500
5700
6000
5800
5500 6000
Stepper motor:53 3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C
3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C

Downloaded from www.Manualslib.com manuals search engine 263
INJECTION
CHECKS: TURBO PRESSURE
Engines: 8HX 8HW
B1BP2NXD
C5FP0F5C
C2 C3
Tools.
[1]Pressure gauge for checking boost pressure: 4073T.A
[2]Sleeve for checking boost pressure: ().0171.F
Checks.IMPERATIVE: Respect the following test conditions:
Engine at operating temperature.
Vehicle in running order. Engine under full load.Preparation.
Remove the clips (1).
Fit the tool [2]in the place of the duct (2).
Couple the sleeve [2]on the pressure gauge [1]using the tube «a».Mode of operation.Position tool [1]in the vehicle.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of
1000 rpm.
Check the pressure:0,6 ± 0,05 bar (1500 rpm).
Accelerate freely (change from fourth gear to third gear).
Check the pressure:0,9 ± 0,05 bar(between 2500 and 3500 rpm).
Remove tools [1], [2]at «a».
Reposition the tube (2)and tighten the clips (1).

Downloaded from www.Manualslib.com manuals search engine 264
INJECTION
CHECKS: TURBO PRESSURE
Engines: 8HV 8HY
Tools.
[1]Pressure gauge for checking boost pressure: 4073T.A
[2]Sleeve for checking boost pressure: ().0171.F
Checks.
IMPERATIVE:
Respect the following test conditions:
Engine at operating temperature.
Vehicle in running order. Engine under full load.
Preparation.Remove the clips (1).
Fit the tool [2]in the place of the duct (2).
Couple the sleeve [2]on the pressure gauge [1] using the tube «a».Mode of operation.Position tool [1]in the vehicle.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of
1000 rpm.
Check the pressure:0,6 ± 0,05 bar (1500 rpm).
Accelerate freely (change from fourth gear to third gear)Check the pressure:0,9 ± 0,05 bar(between 2500 and 3500 rpm).
Remove tools[1],[2]at «a».
Reposition the tube (2)and tighten the clip (1).
C5FP0EJC
B1BP2NBD
C3