instrument panel CITROEN C3 2009 Owners Manual

FAMILIARISATION
INSTRUMENTS AND CONTROLS

1. Audio equipment steering wheel
controls.

2. Steering lock and ignition.

3. Wipers/wash-wipe/trip computer
controls.

4. Instrument panel.

5. Scented air freshener.

6. Driver’s airbag.
Horn.

7. Gear lever.

8. Parking brake.

9. Central armrest with storage.

10. Exterior mirror controls.
Electric window controls.
Rear doors and electric windows deactivation control.

11. Storage compartment.

12. Electric child lock button or
Alarm button.
Electronic stability programme button (ESP/ASR).

13. Side adjustable air vent.

14. Front door window demisting/
defrosting vent.

15. Speaker (tweeter).

16. Windscreen demisting/defrosting
vent.

FAMILIARISATION
MONITORING
Instrument panel

A. With the ignition on, the fuel gauge
bars for the fuel remaining should
light up.

B. With the engine running, the associ-
ated low level warning lamp should
switch off.

C. With the ignition on, the oil level in-
dicator should display "OIL OK" for
a few seconds.
If the levels are not correct, top up the
level which is low.


 18 Warning lamps

1. With the ignition on, the orange and
red warning lamps come on.

2. With the engine running, these
warning lamps should switch off.
If a warning lamp remains on, refer to
the page concerned.


 20 Switch panel
Lighting of the indicator lamp indicates
the status of the corresponding func-
tion.

A. Activation of the electric child lock


 89
or
Deactivation of the interior volumetric alarm.
 59

B. Deactivation of the ESP/ASR system.
 92

FAMILIARISATION
Speed limiter "LIMIT"

1. Selecting/Switching off speed limiter
mode.

2. Decrease the programmed value.

3. Increase the programmed value.

4. Speed limiter on/off.


 104
DRIVING SAFELY
Cruise control "CRUISE"

1. Selecting/Switching off cruise con-
trol mode.

2. Decrease the programmed value.

3. Increase the programmed value.

4. Cruise control Off/Resume.


 106
The values must be set with the engine
running. Display in the instrument panel
The cruise control or speed limiter mode
appears on the instrument panel when
it is selected.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on a manual gearbox
(second gear on an automatic gear-
box). Cruise control
Speed limiter

1
INSTRUMENTS and CONTROLS
Panel grouping together the vehicle operation indication dials and warning lamps.
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS

5. Display management button
Servicing information.
Adjust the time and choose units.
Reset the service indicator.

6. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For further information, refer
to the paragraph relating to the
button or function and its associ-
ated display.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).

3. Fuel level.
Indicates the quantity of fuel remain- ing in the tank.

4. Screen.
A. Ambient temperature.
(°Celsius or °Fahrenheit)

B. Gear change indicator.

C. Time.

D. Engine oil level indicator.
Appears a few seconds after switch- ing on the ignition, then disappears.

E. Trip computer.

F. Service indicator
(miles or km) then,
Total mileage.
These two functions are displayed successively when switching on the
ignition.
Screen

1
INSTRUMENTS and CONTROLS
PETROL - DIESEL MANUAL OR AUTOMATIC GEARBOX
INSTRUMENT PANELS
Panel grouping together the vehicle operation indication dials and warning lamps.
Depending on the version, the instrument panel may have permanent back-lighting.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Vehicle speed.
Indicates the current speed of the moving vehicle (km/h or mph).

3. Fuel level.
Indicates the quantity of fuel remaining in the tank.

4. Screen.
5. Display management button
Alternates display between range and trip mileage recorder.
Servicing information.
Resets the selected function to zero (trip distance recorder or service
indicator).

6. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For further information, refer
to the paragraph relating to the
button or function and its associ-
ated display.
A. Speed limiter
(mph or km/h) or
Cruise control.

B. Gear change indicator.

C. Automatic gearbox information.

D. Range
(miles or km) or
Trip mileage recorder.

E. Service
indicator
(miles or km), then
Total mileage recorder
These two functions are displayed successively when switching on the
ignition

F. Engine oil level indicator
Appears a few seconds after switch- ing on the ignition, then disappears.
Screen

1
INSTRUMENTS and CONTROLS
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life.
The total and trip distances are dis-
played for thirty seconds when the igni-
tion is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.

 With the ignition on, press the button
until zeros appear.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver. Clock
Adjusting the time - Choice of units

 press the button for more than
two seconds: °C or °F is displayed,

 press the button to select °C or °F,

 press the button for more than
two seconds to complete the adjust-
ments.
After approximately 30 seconds without
any action, the screen returns to the
normal display.
To adjust the time of the clock and
choose the units used by the screen,
use the right-hand button on the instru-
ment panel, carrying out the operations
in the following order:

 press the button for more than
two seconds: the minutes fl ash,

 press the button to increase the
minutes,

 press the button for more than
two seconds: the hours fl ash,

 press the button to increase the
hours,

 press the button for more than
two seconds: 24 H or 12 H is dis-
played,

 press the button to select 24 H or
12 H,

1
INSTRUMENTS and CONTROLS
The instrument panel remains lit with
the vehicle speed and cruise control or
speed limiter information, if in use.
If there is an alert or a change in a func-
tion or to a setting, the black panel mode
is interrupted.
Activation

 With the lighting on, press the left
hand button of the instrument panel
several times to progressively re-
duce the dashboard lighting level.

 Press the button again to reduce the
lighting to the minimum level and
switch off the ambience lighting.

 Press the button again to activate
the black panel.
The dashboard lighting rheostat re-
mains operational when in black panel
mode.
Black panel
System allowing certain displays to be
switched off for night driving.
Activation
When the lighting is on:

 press the button to change the
brightness of the instruments and
controls,

 when the level of brightness required
is reached, release the button.
Deactivation
When the lighting is off, or in day mode
on vehicles fi tted with daytime running
lamps, pressing the button does not
have any effect.
Lighting rheostat
System for manual adjustment of the
brightness of the instruments and con-
trols in relation to the exterior brightness.

1
INSTRUMENTS and CONTROLS
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption...).
Screen in instrument panel
Monochrome screen A Zero reset
Data displays

 Press the button, located at the end
of the wiper stalk , to display the
various items of trip computer data
in succession.

 Press the control for more than
two seconds to reset to zero the
distance travelled, the average
fuel consumption and the average
speed.
The trip computer provides the following
information:
- range,
- current fuel consumption,
- distance travelled, - average fuel consumption,
- average speed.

 The next press then returns you to
the normal display.

2
MULTIFUNCTION SCREENS
MONOCHROME SCREEN A
Displays on the screen
This displays the following information:
- time,
- date,
- ambient temperature (this fl ashes if there is a risk of ice),
- status of the doors and boot,
- audio sources (radio, CD...),
- trip computer (refer to the "Instruments and Controls" section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Boot open") may ap-
pear temporarily. These can be cleared
by pressing the "ESC" button. Controls
From the control panel of your Audio
system, you can:

 press the "MENU" button to gain
access to the general menu ,

 press the "  " or "  " buttons to scroll
through the items on the screen,

 press the "MODE" button to change
the permanent application (date, audio
source...),

 press the "  " or "  " buttons to
change a setting value,

 press the "OK" button to confi rm,
or

 press the "ESC" button to abandon
the operation in progress. General menu

 Press the "MENU" button to gain
access to the general menu , then
press the "  " or "  " buttons to
scroll through the various menus:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.

 Press the "OK" button to select the
menu required.
Radio-CD
With the Audio system switched on, once the "Radio-CD" menu has been selected
you can activate or deactivate the func-
tions linked with use of the radio (RDS,
REG), or the CD (introscan, shuffl e, CD
repeat).
For further details concerning the
"Radio-CD" application, refer to the
Audio system part of the "Audio and
Telematics" section.

2
MULTIFUNCTION SCREENS
Vehicle configuration
Once the "Vehicle Confi guration" menu
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "guide-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not active,
faulty). Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.

 Once you have selected a setting,
press the "  " or "  " buttons to
change its value.

 Press the "  " or "  " buttons to
switch respectively to the previous
or next setting.

 Press the "OK" button to save the
change and return to the normal
display or press the "ESC" button
to cancel. Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or
km/l).
Once the fuel consumption units
have been set to mpg, the infor-
mation in the instrument panel
screen on speed and distance
will also be in mph and miles.
For safety reasons, confi guration
by the driver of the multifunction
screen must only be done when
stationary.