wheel bolts Citroen C3 PICASSO RHD 2012.5 1.G Owner's Manual

Practical information
156














Changing a wheel
The tools are installed under the boot floor.
For access to them:)open the boot, )remove the boot floor, )lift up the boot carpet, )remove the box containing the tools, )remove the polystyrene storage box.

Other accessories
5.
Removable towing eye.
Refer to the paragraph "Towing the vehicle".
Access to the tools
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.


List of tools

All of these tools are specific to your vehicle. Do not use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts. 2. Jack with integral handle.
For raising the vehicle. 3. "Bolt cover" tool.
For removing the bolt protectors (covers)on alloy wheels. 4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special "security" bolts (if your vehicle has them).

11
Practical information
157

Wheel with trim
When removing the wheel
, firstdetach the trim using the wheelbrace 1pulling at the valve passage hole. When refitting the wheel
, refit the trim starting by placing its notch facing the valve and press around its edge withthe palm of your hand.

Access to the spare wheel
The spare wheel is installed in the boot under
the floor.
According to country, the spare wheel may be steel or of the "space-saver" type.
For access to it, refer to the paragraph "Access
to tools" on the previous page.
Fitting the steel or "space-saver" type sparewheel

If your vehicle is fitted with alloy wheels, it is normal to notice, when tightening the bolts on fitting, that the washers donot come into contact with the steel or "space-saver" type spare wheel. Thewheel is secured by the conical contactof each bolt.

11
Practical information
159
Removing a wheel

List of operations
)
Remove the bolt cover from each of the bolts using the tool 3(with allow wheels
only).) Fit the security socket 4
to the
wheelbrace 1to slacken the security bolt(if your vehicle has them).) Slacken the other bolts using the
wheelbrace 1only.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,stable and non-slippery. Apply the parking brake, switch off theignition and engage first gear to lockthe wheels. If necessary, place a chock under thewheel diagonally opposite the wheel to be changed. You must ensure that the occupants getout of the vehicle and wait where theyare safe. Never go underneath a vehicle raisedusing a jack; use an axle stand.

Practical information
160
Place the jack 2 in contact with one of the
two front A or rear Blocations provided on
the underbody, whichever is closest to the
wheel to be changed. )Extend the jack 2 until its base plate is in contact with the ground. Ensure that thecentreline of the jack base plate is directly below the location A
or Bused.
)
Raise the vehicle until there is sufficient space between the wheel and the ground
to admit the spare (not punctured) wheeleasily. ) Remove the bolts and store them in a clean place.)
Remove the wheel.

11
Practical information
161

List of operations
)
Put the wheel in place on the hub. )
Screw in the bolts by hand as far aspossible.)
Pre-tighten the security bolt (if your vehiclehas them) using the wheelbrace 1
fitted
with the security socket 4 . )
Pre-tighten the other bolts using the
wheelbrace 1only.

Refitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checkedby a CITROËN dealer or a qualified workshop without delay. Have the punctured wheel repaired and replace it on the vehicle as soon aspossible.

Practical information
162
Tighten the security bolt (if your vehicle has
them) using the wheelbrace 1 fitted with thesecurity socket 4
. )
Tighten the other bolts using the
wheelbrace 1 only.)
Refit the bolt covers on each of the bolts(with alloy wheels only).)
Store the tools in the box.
)Lower the vehicle fully. )Fold the jack 2
and detach it.

11
Practical information
187
"Comfort":
front and rear parking sensors, insulated module, reading lamp, sun blinds, head
restraint-mounted coat hanger, centre armrest,
air deflector, scented air freshener car tridges, portable ashtray, solar films for windows...


"Protection":

mats *
, seat covers, mudflaps, bumper
protectors, vehicle protective cover, dog guard,
pet seat and boot covers...

"Transport solutions":

boot liner, boot carpet, towbar, towbar wiring harness, transverse and longitudinal roof
bars, bicycle carrier, ski carrier, roof box, bootspacers, boot net, business/commercial vehicle
conversion kit, sliding boot floor...
"Safety and security":
anti-theft alarm, warning triangle, high visibility
vest, breathalyzer, first aid kit, snow chains,non-skid covers, security wheel bolts, vehicle
tracking system, child seats, fire extinguisher,
caravan mirror, glass security films...
"Style":
allow wheels, chromed mirror shells, leather
steering wheel, gear lever knob, aluminium
footrest, wheel caps...




Accessories A wide range of accessories and genuine par ts is available from the CITROËN dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from CITROËN's recommendation and warranty.

*
To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and
secured correctly,
- never fit one mat on top of another.