Rod Citroen C3 PLURIEL 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 90
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
CYLINDER HEAD (mm)
Engine types 6FZ RFN RFS WJY RHY RHZ
Maximum permissible bow 0,05 0,03
Gasket surface regrinding 0,30 0,20 0,40
TIGHTENING TORQUES ( m.daN)
Pretightening (1) Ø 11 : 1 ± 0,1 2 ± 0,1 2,5 ± 0,3
(2) Ø 6 : 1 ± 0,1
Slackening Ø 11 (only)
Tightening Ø 11 to 1 ± 0,1 8,5 ± 0,8 7 ± 0,7
Crankshaft then to 2 ± 0,1
bearing screws Tightening Angular Ø 11 at 70° ± 5° 60° ± 6° 60° ± 6°
Tightening Ø 6 to 1 ± 0,1
Pretightening 1 ± 0,1 4 ± 0,4 2 ± 0,2
ConnectingSlackening 180° (1/2 turn)
rod screws Tightening 2,3 ± 0,2 2,3 ± 0,2 2± 0,2
Angular tightening46°±5°46° ±4,6° 70° ± 7° 70° ± 7°
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 91
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines: 9HZ 9HY
Torque reaction rod
1 : 5,4 ± 0,8
2 : 5,4 ± 0,8
13 : 6 ± 0,9
LH upper engine support
3 : 2,1 ± 0,2
4 : 5 ± 0,5
LH lower engine support
5 : 2,1 ± 0,2
6 : 5,7 ± 0,8
RH lower engine support
7 : 5,5 ± 0,5
RH engine support
8:4,5 ±0,4
9 : 4,5 ± 0,6
10:2,5 ±0,6
11:2,1 ± 0,2
12 : 6,1 ± 0,6
B1BP2Z4P
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 92
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines9HZ 9HY
Crankshaft
Bearing cap fixing screw
Pretightening1 ± 0,2
Slackening180°
Tightening3 ± 0,3
Angular tightening140°
Con rod screws
Tightening1 ±0,1
Angular tightening100 ±5°
Accessories drive pulley
Pretightening3,5 ± 0,4
Angular tightening190 ± 5°
Cylinder block
Sump 1,3 ± 0,1
Timing belt guide roller3,7 ± 0,3
Timing belt tensioner roller2,7 ± 0,2
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 220
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Remove:
The fixings of the pipe linking the power steering pump with the rotary valve.
The clutch lower closing plate.
Lock the engine flywheel, using tool
[6].
Remove the screw (8).
Refit the screw (8)without its thrust washer.
Remove:
The accessories pulley
(9), using tool[8].
Tool [6].
The lower torque reaction rod.
Support the engine by means of a workshop hoist.
Remove:
The bearing shell fitting
(10).
The nut (12).
Screws (11).
The bracket (13).
NOTE:Lift then lower the engine with the workshop hoist, to have access to the
timing cover fixing screws.
Remove:
The intermediate timing cover.
The lower timing cover.
B1CP04BCB1BP2R3CB1BP2R4C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 269
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
Vacuum pump.
Connect the tool [1]on the vacuum pump (1).
Start the engine.
Pressure should be
0.8 barat 780 rpm.Boost pressure regulator electrovalve. Connect the tool [1]between the electrovalve (2)and the valve (3)of the boost pressure
regulator.
Compare readings with the values in the table below.
Pressure regulator valve. Connect the tool [1]on the valve (3).
Appy a pressure of 0.5 barto activate the rod "a":
Rod "a"should be moved 12 mm.
Engine speed (rpm) Pressure (Bar)
780 0,6
4000 0,25
B1HP12FD

Downloaded from www.Manualslib.com manuals search engine 270
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: 8HX 8HW
Engines: 8HV 8HY
Tools.
[1]
Manual pressurevacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel
injection (HDi) engines.
EGR v
alve.Connect tool [1]on the capsule takeoff (2).
Apply a vacuum of approx.0,6 barseveral times to activate the rod «a».
In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
Regulation electrovalve (EGR).(Engine:8HX8HW).Check to be performed between the electrovalve (1)and the EGR valve (2).
Link the tool [1]in series, between the electrovalve (1)and the capsule (2).
Compare the values noted with those in the table below.
Regulation electrovalve (EGR).(Engine:8HV8HY).Check to be performed between the electrovalve (2)and the EGR valve (1).
Link the tool [1] in series, between the electrovalve (2)and the capsule (1).
Compare the values noted with those in the table below.
Engine speed (rpm) Vacuum value
780 0,5
2500 0
B1HP15GD
B1HP1K6D
C2 C3

Downloaded from www.Manualslib.com manuals search engine 272
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]
Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
EGR valve.
Connect the tool [1]to the capsule union (1).
Apply several times in succession a vacuum of approx.0.6 barto activate the rod "a".
In abrupt reaction to the vacuum, the valve should close on its seating with a clicking
noise.
Exhaust gas reycling (EGR) electrovalve. Check, not under load, between the electrovalve (2)and the EGR valve (1).
Connect the tool [1]between the electrovalve (2)and the capsule (1).
Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value
7800,5
25000
B1HP12GD

Downloaded from www.Manualslib.com manuals search engine 273
INJECTION
PARTICLE FILTER SAFETY AND CLEANLINESS REQUIREMENTS
General.
ESSENTIAL: Given the very high pressures prevailing in the fuel high pressure circuit (1600 Bars), respect the following regulations.
It is forbidden to smoke in the immediate proximity of the high pressure circuit during a repair.
Avoid working close to flames or sparks.When the engine is running:
Do touch the fuel high pressure circuit.
Always keep out of range of possible projections of fuel, which could cause serious injuries.
Do not place your hand near to any leak on the fuel high pressure circuit. After the engine has stopped, wait 30 seconds before starting any operation.
NOTE:The waiting time is necessary to allow the fuel high pressure circuit to return to atmospheric pressure.
Safety rules.
IMPERATIVE:Wait at least an hour before starting any repair on the exhaust line.
Forced regeneration of the particle filter:
Check that there are no aerosols or inflammable products inside the vehicle’s boot.
Wear high temperature gloves.
Connect the vehicle to a gas extractor approved for this type of operation.
IMPERATIVE: In the absence of the required installations, carry out the forced regeneration of the particle filter outside the workshop,
in a concreted area well away from any inflammable materials. Place the vehicle in the high position.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 274
INJECTION
PARTICLE FILTER SAFETY AND CLEANLINESS REQUIREMENTS
Operations on the fuel additive circuit.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves that are resistant to hydrocarbons.
The work area must be ventilated.
In the event of any significant dispersion of additive:
Wear a breathing mask for filtering the particles.
Recover as much of the product as possible.
Place the product thus recovered in an appropriately labelled container. Wash the soiled area with copious amounts of water.
Dispose of materials and solid residues in an authorised recovery point.
IMPERATIVE:The filling kit should be recycled following a repair. All «Eolys» additive containers that have been opened should be
disposed of.
Cleanliness rules.
ESSENTIAL: The operator should wear clean overalls.
Before working on the injection circuit, it may be necessary to clean the unions of the following sensitive components(see corresponding operations).
Fuel filter.
Fuel high pressure pump.
Fuel high pressure regulator.
Fuel high pressure common injection rail. Fuel high pressure piping. Diesel injector carriers.
IMPERATIVE: After dismantling, immediately blank the unions of the sensitive components with plugs, to prevent any ingress of impurities.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 279
1.1iHFX
FR7 DE RFN 58 LZ RC 8 YLC
C2 1.4i KFV
1.6i 16V NFU FR7 ME 0,9 ± 0,1 RFN 58 HZ
1.1i HFX
FR7 DERFN 58 LZ RC 8 YLC
1.4i KFV
C3 1.4i 16V KFU VR8 SE 0,9 ± 0,05
1.6i 16V NFU FR7 ME RFN 58 HZ
C3 1.4i KFV FR7 DE RFN 58 LZ RC 8 YLC
PLURIEL1.6i 16VNFUFR7 MERFN 58 HZ
0,9 ± 0,05 0,9 ± 0,05 2.5 ± 0,2
1.4iKFWFR7 DE0,9 ±0,1 RFN 58 LZ RC 8 YLC mda.N
XSARA 1.6i 16V NFU FR7 ME RFN 58 HZ
2.0i 16V RFN FR8 ME RFN 52 HZ REC 9 YCL
RFSFR6 DE RFN 62 LZ
1.6i90 hp
NFVRFN 58 LZ
XSARA100 hpFR7 DE RC 8 YLC
PICASSO 1.8i 16V 6FZ
FR8 ME0,9 ± 0,1
RFN 52 HZ REC 9 YCL
2.0i 16V RFN
SPARKING PLUGS ALL TYPES
Vehicles
BOSCH Engine
typeEYQUEM
CHAMPION Electrode
gap settingTightening
torque
IGNITION
Electrode
gap settingElectrode
gap setting