steering wheel Citroen C4 2005 2.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 391
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
(*) = Difficult road conditions.
Compress the suspension to obtain the calculated values.
NOTE: The difference in height between the two sides should be less than10 mm. Measure the radius of the rear wheel: R2.
Calculate the dimensionH2. Measure the radius of the front wheel: R1.
Calculate the dimension H1 orH1’.
Checks at reference height (the reference height of the vehicle is set as per the table below).
B3CP05BCB3CP05AC
XSARA PICASSO
Front axleRear axle
Front axle
Rear axle CRD vehicle versions (*)
H1 = R1 – L1 or H1’ = R1 – L1’
L1 = 75,5 mmL1’ = 109 mmL2 = 23,5 mmH2 = R2 + L2
B3DP079C
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 391

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).(1) Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg
(4)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6)Anti-roll bar
(7)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(8)Lower swivel ball-joint: 4 ± 0.4
(9)Hub nut
(greased): 32.5 ± 2
(10)Wheel bolt
(face and threads not greased): 9 ± 1
(11) Lower arm front pivot: 7.6 ± 0.7
(12) Lower arm rear pivot and
anti-roll bar bearing: 6.8 ± 0.6
(13) Screw under rear pivot : 3.5 ± 0.3
Lower arm in forged steel : 3.7 ± 0,3
Lower arm in plate steel: 3.1 ± 0,3
Screw fixing subframe on bodyshell: 8.5 ± 0,8
Screw fixing ball-joint on lower
arm
(plate steel): 4.5 ± 0,4
Anti-roll bar
Engines
ALL TYPESDiameter
21Colour ref.
WHITE Suspension leg angle:
Ta b«a»towards the front.
B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 393

Downloaded from www.Manualslib.com manuals search engine 394
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(14)Front silentblock on subframe: 9.4 ± 0.9
(15)Anti-roll bar bolt: 5.5 ± 0.5
(16)Rear torsion bar
(17) Anti-roll bar
(18) Tubular axle
(19)Front silentblock on bodyshell: 4 ± 0.4
(20)Rear upper arm.
(21)Wheel bolt
(face and threads not lubricated): 9 ± 1
(22)Damper
(23)Rear silentblock on subframe: 5.4 ± 0.5
(24)Damper pin nut: 11 ± 1
(25)Stub axle nuts
(lubricated): 25 ± 2
(26)Rear silentblock on bodyshell: 6.5 ± 0.6
Anti-roll bar
Torsion bar
Engines
ALL TYPES 19,6 PINKØ (mm)
Colour ref.Ø (mm)
21Colour ref.
ORANGE
B3DP078D
NOTE: The RH torsion bar can be identified by 1 paint line.
The LH torsion bar can be identified by 2 paint lines.
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 394

Downloaded from www.Manualslib.com manuals search engine 395
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
Tightening torques (m.daN).
(2) Airbag to steering wheel fixing: 0.8 ± 0.1
(3)Steering wheel fixing: 3.3 ± 0.6
(5)Steering column to support fixing: 4 ± 0.1
(6)Steering cardan joint fixing: 2.3 ± 0.2
B3EP116D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 395