reset Citroen C4 2010 2.G Owner's Manual

Page 5 of 284

8
F A M I L I A R I S A T I O N
D A S H B O A R D

1. Controls:
- Mirrors.
- Windows.
- Child safety

2. Headlamp adjustment.

3. Control switches:
- ESP.
- Parking sensors.
- Lane departure warning system.
- Anti-intrusion alarm.

4. Steering lock and ignition switch.

5. Control stalk:
- Windscreen wiper.
- Screen wash.
- Rear screen wiper.
- Trip computer.

6. Fixed centred controls.

7. Direction indicator warning lamps.

8. Speedometer

9. Controls:
- Trip mileage recorder reset button.
- Display lighting rheostat.
- Display of alerts and status of functions.

10. Centre air vents.

11. Driver’s airbag.

12. Horn

13. Gear lever.

14. Parking brake.

Page 20 of 284

23
I
M O N I T O R I N G
INSTRUMENT PANEL WITH TRANSLUCENT SCREEN
The instrument panel groups all the driving and comfort information at the centre of the dashboard.
Central screen
5. Trip mileage recorder

6. Fuel gauge

7. Engine oil level check

8. Coolant temperature Control buttons

1. Rev counter

2. Cruise control or speed limiter
setting

3. Speedometer

4. Service indicator when the ig-
nition is switched on, then total
mileage recorder
A. Trip mileage recorder reset

B. Lighting rheostat

C. Display of alerts and Status of
functions

Page 24 of 284

27
I
M O N I T O R I N G
Airbags If this comes on, it indicates
the occurrence of a fault in
one of the airbag or seat belt
pretensioner systems.
Door open
A door, the boot or the bonnet
is open:
- if the speed is below 6 mph (10 km/h), this warning lamp
comes on continuously.
-
if the speed is higher than 6 mph
(10 km/h), this warning lamp comes
on continuously, accompanied by
an audible signal.
Seat belt not fastened/unfastened
Driver's seat belt not fas-
tened:
- The warning lamp comes on if the driver's seat belt is not fastened
when the ignition is switched on
and between 0 and 12 mph (ap-
prox. 20 km/h).
- Above 12 mph (approx. 20 km/h), the warning lamp fl ashes for ap-
proximately 120 seconds, accom-
panied by an audible signal. It
then remains on.
Front passenger and rear passenger
seat belts not fastened:
- When the ignition is switched on, the warning lamp always comes
on if the passenger's seat belt is
not fastened.
It goes off when the engine is running,
doors closed and after 30 seconds.
- If a seat belt is unfastened, the warning lamp comes on between
0 and 20 km/h (approx. 12 mph).
- Above 20 km/h (approx. 12 mph), the warning lamp fl ashes for
approximately 120 seconds, ac-
companied by an audible signal. Service indicator
System which informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is
due is calculated from the last indi-
cator zero reset. It is determined by
two parameters:
- the distance travelled,
- the time elapsed since the last
service.

Page 29 of 284

27
I
M O N I T O R I N G
Airbags If this comes on, it indicates
the occurrence of a fault in
one of the airbag or seat belt
pretensioner systems.
Door open
A door, the boot or the bonnet
is open:
- if the speed is below 6 mph (10 km/h), this warning lamp
comes on continuously.
-
if the speed is higher than 6 mph
(10 km/h), this warning lamp comes
on continuously, accompanied by
an audible signal.
Seat belt not fastened/unfastened
Driver's seat belt not fas-
tened:
- The warning lamp comes on if the driver's seat belt is not fastened
when the ignition is switched on
and between 0 and 12 mph (ap-
prox. 20 km/h).
- Above 12 mph (approx. 20 km/h), the warning lamp fl ashes for ap-
proximately 120 seconds, accom-
panied by an audible signal. It
then remains on.
Front passenger and rear passenger
seat belts not fastened:
- When the ignition is switched on, the warning lamp always comes
on if the passenger's seat belt is
not fastened.
It goes off when the engine is running,
doors closed and after 30 seconds.
- If a seat belt is unfastened, the warning lamp comes on between
0 and 20 km/h (approx. 12 mph).
- Above 20 km/h (approx. 12 mph), the warning lamp fl ashes for
approximately 120 seconds, ac-
companied by an audible signal. Service indicator
System which informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is
due is calculated from the last indi-
cator zero reset. It is determined by
two parameters:
- the distance travelled,
- the time elapsed since the last
service.

Page 30 of 284

27
I
M O N I T O R I N G
Airbags If this comes on, it indicates
the occurrence of a fault in
one of the airbag or seat belt
pretensioner systems.
Door open
A door, the boot or the bonnet
is open:
- if the speed is below 6 mph (10 km/h), this warning lamp
comes on continuously.
-
if the speed is higher than 6 mph
(10 km/h), this warning lamp comes
on continuously, accompanied by
an audible signal.
Seat belt not fastened/unfastened
Driver's seat belt not fas-
tened:
- The warning lamp comes on if the driver's seat belt is not fastened
when the ignition is switched on
and between 0 and 12 mph (ap-
prox. 20 km/h).
- Above 12 mph (approx. 20 km/h), the warning lamp fl ashes for ap-
proximately 120 seconds, accom-
panied by an audible signal. It
then remains on.
Front passenger and rear passenger
seat belts not fastened:
- When the ignition is switched on, the warning lamp always comes
on if the passenger's seat belt is
not fastened.
It goes off when the engine is running,
doors closed and after 30 seconds.
- If a seat belt is unfastened, the warning lamp comes on between
0 and 20 km/h (approx. 12 mph).
- Above 20 km/h (approx. 12 mph), the warning lamp fl ashes for
approximately 120 seconds, ac-
companied by an audible signal. Service indicator
System which informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is
due is calculated from the last indi-
cator zero reset. It is determined by
two parameters:
- the distance travelled,
- the time elapsed since the last
service.

Page 32 of 284

29
I
M O N I T O R I N G
Service indicator zero reset Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL

--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine.
There are 2 marks on the
dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type of
oil suited to your en-
gine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

Page 33 of 284

30
I
M O N I T O R I N G
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other pe-
riod since it was reset to zero by the
driver.

 With the ignition on, press the
button until zeros appear. Dashboard lighting rheostat
Activation

 Turn control A or press control

B to adjust the brightness of the
dashboard lighting,

 With control B , press until the
brightness is at maximum, re-
lease, press until you reach mini-
mum.
Deactivation
When the vehicle lighting is off, or in
day mode in the case of vehicles fi t-
ted with daytime running lamps, the
button has no effect.
System permitting manual adjustment
of the brightness of the dashboard to
suit the level of ambient light.
The rheostat is active if the sidelamps
are on and applies to:
- the instrument panel,
- the display screens.

Page 40 of 284

37
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current infor-
mation concerning the trip travelled
(range, fuel consumption...).
Monochrome screen A Information displays

 Press the control for more than
two seconds to reset to zero the
distance travelled, the average
fuel consumption and the aver-
age speed.
Zero reset
The trip computer provides the fol-
lowing information:
- range,
- current fuel consumption,
- distance travelled,
- average fuel consumption,
- average speed.

 The next press then returns you
to the normal display.

 Press the button, located at the
end of the wiper stalk , to display
the various items of trip comput-
er data in succession.

Page 41 of 284

38
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, fuel consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with:


Page 43 of 284

38
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, fuel consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with:


Page:   1-10 11-20 next >