turn signal Citroen C4 DAG 2014.5 2.G Owner's Manual

22
C4-2_en_Chap01_controle-de-marche_ed01-2014
Water in Dieselfixed.The   Diesel   fuel   filter   contains  water
.Risk
  of   damage   to   the   injection   system  on
  Diesel   engines.
Contact   a   CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Particle
emissions filter (Diesel) fixed,
 
accompanied

  by  
an

  audible   signal  
message

  on   the  
risk

  of   blockage  
of the particle
emissions

  filter.This
  indicates   that   the   particle  
emissions

  filter   is   starting   to  
become

  saturated.As
  soon   as   driving   conditions   allow,  
regenerate

  the   filter   by   driving   at   a   speed  
of

  at   least   35   mph   (60   km/h)   until   the  
warning

  lamp   goes   off.
fixed,
 
accompanied by

  an   audible
 signal

  and   and   a
 message

  that   the
 particle

  emissions
 filter

  additive   level
 is

  too   low.This
  indicates   the   low   level   of  
the

  additive   reservoir.Have
  the   reservoir   topped   up   as   soon  
as

  possible   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Warning/indicator lamp
is onCause Action/Observations
Airbags temporarily.
This   lamp   comes   on   for   a   few  
seconds

 
when
 
you
 
turn
 
on
 
the
 
ignition,

  then   goes   off.
This   lamp   should   go   off   when   the   engine  
is

  started.
If   it   does   not   go   off,   contact   a   CITROËN  
dealer

  or   a   qualified   workshop.
fixed. One   of   the   airbag   or   seat   belt  
pretensioner

  systems   has   a  
fault.
Have
  it   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop.
1
MonIToRInG

24 
C4-2_en_Chap01_controle-de-marche_ed01-2014
Warning/indicator lampis onCause Action/Observations
+
+ SCR emissions
control system
(BlueHDi Diesel)
fixed, on  switching  on
  the   ignition,  
associated

  with  
the

  SERVICE   and  
engine

  diagnostic  
warning

  lamps,  
accompanied

  by  
an

  audible   signal  
and

  a   message  
indicating

  an  
emissions

  control  
fault.
a fault with the SCR
emissions   control   system   has  
been

  detected. This
  alert   disappears   once   the   exhaust  
emissions

  return   to   normal   levels.
flashing, on switching  on  
the

  ignition,  
associated

  with  
the

  SERVICE   and  
engine

  diagnostic  
warning

  lamps,  
accompanied

  by   an  
audible

  signal   and   a  
message

  indicating  
the

  remaining  
driving

  range.
The remaining driving range is  between   0   and   650   miles  
(1
  100   km). Contact
  a   CITROËN   dealer   or   a   qualified  workshop
  without delay, to avoid a
breakdown.
flashing, on switching   on  
the

  ignition,  
associated

  with  
the

  SERVICE   and  
engine

  diagnostic  
warning

  lamps,  
accompanied

  by   an  
audible

  signal   and   a  
message

  indicating  
that

  starting   is  
prevented.
You have exceeded the authorised  driving   limit:   the  
starting

  inhibition   system  
prevents

  starting   of   the  
engine. T

o   be   able   to   start   the   engine,   you   must
call
  on   a   CITROËN   dealer   or   a   qualified  
workshop.
1
MONITORING

25 
C4-2_en_Chap01_controle-de-marche_ed01-2014
Operation indicator lamps
If  one   of   the   following   indicator   lamps   comes   on,   this   confirms   that   the   corresponding   system   has   come   into   operation.
It
  may   be   accompanied   by   an   audible   signal   and   a   message   in   the   screen.
Warning/indicator lamp is onCause Action/Observations
Left-hand direction
indicator flashing
  with  
buzzer

.The
  lighting   stalk   is   pushed  
down.
Right-hand direction
indicator flashing

  with  
buzzer

.The
  lighting   stalk   is   pushed   up.
Hazard warning lamps flashing
  with  
audible

  signal.The
  hazard   warning   lamps
 switch,

  located   on   the
 dashboard,

  has   been   operated.The
  left-hand   and   right-hand   direction  
indicators

  and   their   associated   indicator  
lamps

  flash   simultaneously.
Sidelamps fixed.The
  lighting   stalk   is   in   the  
"Sidelamps"

  position.
Dipped beam headlamps fixed.The
  lighting   stalk   is   in   the  
"Dipped

  beam   headlamps"  
position

  or   in   the   "AUTO"  
position

  in   conditions   of   low  
light.
Main beam
headlamps fixed.The

  lighting   stalk   is   pulled  
towards

  you.Pull
  the   stalk   again   to   return   to   dipped  
beam

  headlamps.
Front foglamps fixed.The
  front   foglamps   are  
switched

  on   using   the   ring   on  
the

  lighting   control   stalk.Turn
  the   ring   on   the   lighting   control   stalk  
rearwards

  twice   to   switch   off   the   front  
foglamps.
Rear foglamps fixed. The

  rear   foglamps   are   on.Turn
  the   ring   on   the   stalk   rearward   to   turn  
of

f   the   rear   foglamps.
1
MONITORING

69 
C4-2_en_Chap04_ouvertures_ed01-2014
Operating fault with the
2-button remote control
Following disconnection of  the  vehicle  battery
,  replacement  of  the  remote  con -
trol
 
battery
 
or
 
in
 
the
 
event
 
of
 
malfunction
 
of

 
the
 
remote
 
control,
 
you
 
can
 
no
 
longer
 
unlock,

  lock   or   locate   your   vehicle.
F
 
First
 
of
 
all,
 
use
 
the
 
key
 
in
 
the
 
lock
 
to
 
unlock

  or   lock   your   vehicle.
F
 
Then,
  reinitialise   the   remote   control.
Reinitialisation
F
 
Switch
  off   the   ignition.
F

Turn the  key  to  position  2 (Ignition on) .
F Press the  closed  padlock  immedi -
ately   for   a   few   seconds.
F
 
Switch
 
of
f  
the
 
ignition
 
and
 
remove
 
the

  key   from   the   ignition   switch.
The
 
remote
 
control
 
is
 
fully
 
operational
 
again. Battery

  ref.:   CR1620/3   volts.
Changing the battery
If the
 battery  is  flat,  you  are  in -
formed  by  illumination  of  this warning

 
lamp,
 
an
 
audible
 
signal and

  a   message   in   the   screen.
F Unclip the  casing  using  a  coin  at  the  notch.
F
 
Slide
 
the
 
flat
 
battery
 
out
 
of
 
its
 
loca
-
tion.
F
 
Slide
 
the
 
new
 
battery
 
into
 
its
 
loca
-
tion
  observing   the   original   direction.
F
 
Clip
  the   casing.
F
 
Reinitialise
  the   remote   control.
If
 
the
 
problem
 
persists,
 
contact
 
a

 
CITROËN
 
dealer
 
as
 
soon
 
as
 
possible.
4
ACCESS

73 
C4-2_en_Chap04_ouvertures_ed01-2014
Emergency control
System allowing the  doors  to  be  locked  and
 unlocked  manually  in  the  event  of  
a

 
malfunction
 
of
 
the
 
central
 
locking
 
sys
-
tem
  or   battery   failure.
Locking the driver's door
F
 
Insert
 
the
 
key
 
in
 
the
 
door
 
lock,
 
then
 
turn

  it   to   the   rear.
You
 
can
 
also
 
apply
 
the
 
procedure
 
de
-
scribed
  for   the   passenger   doors.
Unlocking the driver's door
F
 
Insert
 
the
 
key
 
in
 
the
 
door
 
lock,
 
then
 
turn

  it   to   the   front. Locking the front and rear
passenger doors
Unlocking the front and rear
passenger doors
F
 
Pull
 
the
 
interior
 
door
 
opening
 
control.
F

 
Open
  the   doors.
F
 
On
 
the
 
rear
 
doors,
 
check
 
that
 
the
 
child

 
lock
 
is
 
not
 
on
 
(see
 
the
 
corre
-
sponding
  section).
F
 
Remove
 
the
 
black
 
cap,
 
located
 
on
 
the

  edge   of   the   door,   using   the   key.
F
 
Insert
 
the
 
key
 
in
 
the
 
socket
 
without
 
forcing

 
it,
 
then
 
without
 
turning
 
it,
 
move

 
the
 
latch
 
sideways
 
towards
 
the

  inside   of   the   door.
F
 
Remove
  the   key   and   refit   the   cap.
F
 
Close
 
the
 
doors
 
and
 
check
 
that
 
the
 
vehicle

 
has
 
locked
 
correctly
 
from
 
the

  outside.
Activation / Deactivation
You
 
can

 
activate

 
or

 
deactivate

 
this

 
func

-
tion
 
permanently.
F
 
With

 
the

 
ignition

 
on,

 
press

 
this

 
but

-
ton
 
until

 
an

 
audible

 
signal

 
starts

 
and

 
a

 
corresponding

 
message

 
is

 
dis

-
played.
the
 
state

 
of

 
the

 
system

 
stays

 
in

 
memory

 
when

 
switching
 
off
 
the
 
ignition.
4
ACCESS

55
84 
C4-2_en_Chap05_visibilite_ed01-2014
Parking lamps
Side markers for  the  vehicle  by  illu mi-
nation  of  the  sidelamps  on  the  traffic  
side

  only.
F
 
Within
 
one
 
minute
 
of
 
switching
 
of
f  
the

 
ignition,
 
operate
 
the
 
lighting
 
con
-
trol
 
stalk
 
up
 
or
 
down
 
depending
 
on
 
the

 
traffic
 
side
 
(for
 
example:
 
when
 
parking

 
on
 
the
 
left;
 
lighting
 
control
 
stalk

 
upwards;
 
the
 
right
 
hand
 
side
-
lamps
  are   on).
This
 
is
 
confirmed
 
by
 
an
 
audible
 
signal
 
and

 
illu
mination  
of
 
the
 
corresponding
 
direction

 
indicator
 
warning
 
lamp
 
in
 
the
 
instrument

  panel.
To
 
switch
 
of
f  
the
 
parking
 
lamps,
 
return
 
the

 
lighting
 
control
 
stalk
 
to
 
the
 
central
 
position.
Switching off the lighting when


switching off the ignition
When
 the
 ignition
 is
 switched
 of
f, all

 
of

 
the

 
lamps

 
switch

 
of

f
 
immedi

-
ately,
 
except

 
for

 
the

 
dipped

 
beam headlamps

 
if

 
automatic

 
guide-
me-home

 
lighting
 
is
 
activated.
Manual guide-me-home lighting
The temporary  illumination  of  the  dipped beam
 headlamps  after  the  vehicle's  ignition has

 
been
 
switched
 
of
f  
makes
 
the
 
driver's exit

  easier   when   the   light   is   poor.
Switching on
F 
With
 
the
 
ignition
 
of
f,  
"flash"
 
the
 
headlamps

  using   the   lighting   stalk.
F
 
A further
 
"headlamp
 
flash"
 
switches
 
the

  function   off.
Switching off
The
 
manual
 
guide-me-home
 
lighting switches

 
of
f  
automatically
 
after
 
a
 
set
 
time.
Switching on the lighting


when switching on the ignition
To reactivate  the  lighting  control stalk, turn the  ring  A to position "0"   -  lighting off, then  to  the  position  of your
  choice.
If
 
the
 
lighting
 
is
 
switched
 
on
 
manu
-
ally
 
after
 
switching
 
of
f  
the
 
ignition, there

 
is
 
an
 
audible
 
signal
 
when
 
a front

 
door
 
is
 
opened
 
to
 
warn
 
the driver

 
that
 
they
 
have
 
forgotten
 
to switch

 
of
f  
the
 
vehicle's
 
lighting,
 
with the

  ignition   off.
They
 
switch
 
of
f  
automatically
 
after
 
a period

 
which
 
depends
 
on
 
the
 
state of

 
charge
 
of
 
the
 
battery
 
(entry
 
to
 
en
-
ergy
  economy   mode).
VISIBILITY

55
85 
C4-2_en_Chap05_visibilite_ed01-2014
Automatic illumination of
headlamps
The sidelamps and  dipped  beam  head -
lamps  are  switched  on  automatically ,  
without any action on the part of the
driver

,  
when
 
a
 
low
 
level
 
of
 
external
 
light
 
is

 
detected
 
or
 
in
 
certain
 
cases
 
of
 
activa
-
tion
  of   the   windscreen   wipers.
As
 
soon
 
as
 
the
 
brightness
 
returns
 
to
 
a
 
sufficient

 
level
 
or
 
after
 
the
 
windscreen
 
wipers

 
are
 
switched
 
of
f,  
the
 
lamps
 
are
 
switched

  off   automatically.
Activation
F
 
T
urn  
ring
 
A to the

"AUTO"  
position. The

 
automatic
 
illumination
 
of
 
head
-
lamps
  is   accompanied   by  
a
 
message in

  the   screen.
Deactivation
F
 
T
urn  
ring
 
A
to a position other
than

"AUT
O".  
Deactivation
 
is
 
ac
-
companied
 
by
 
a
 
message
 
in
 
the
 
screen.Coupling with the automatic "Guide-
me-home" lighting
Association

 with  the  automatic  illu mi-
nation  of  headlamps  provides  "guide-
me-home"
 
lighting
 
with
 
the
 
following
 
additional

  options:
-
 
selection
 
of
 
the
 
lighting
 
duration
 
to
 
15,

 
30
 
or
 
60
 
seconds
 
in
 
the
 
settings
 
in

 
the
 
vehicle
 
configuration
 
menu
 
(except

 
in
 
the
 
case
 
of
 
the
 
mono
-
chrome
 
screen
 
A,
 
for
 
which
 
the
 

duration

  is   set:   60   seconds),
-
 automatic

 
activation
 
of
 
"guide-me-
home"

 
lighting
 
when
 
automatic
 
illumi
-
nation
  of   headlamps   is   in   operation.
In the event of a fault with the
sunshine sensor ,  the  lighting come

 
on,
 
this
 
warning
 
lamp
 
is displayed

 
on
 
the
 
instrument
 
panel
 
and/or
 
a message

 
appears
 
in
 
the
 
screen,
 
accompa
-
nied
 
by
 
an
 
audible   signal.
Contact
 
a

 
CITROËN
 
or
 
a
 
qualified
 
work
-
shop
 
workshop.
Operating fault
In  
fog
 
or
 
snow
,  
the
 
sunshine
 
sensor

 
may
 
detect
 
sufficient
 
light.

 
Therefore,
 
the
 
lighting
 
will
 
not

  come   on   automatically.
d

o not cover the sunshine sen-
sor,
 
coupled
 
with
 
the
 
rain
 
sensor
 
and

 
located
 
in
 
the
 
centre
 
of
 
the
 
windscreen

 
behind
 
the
 
rear
 
view
 
mirror;

 
the
 
associated
 
functions
 
would

  no   longer   be   controlled.
VISIBILITY

99
136 
C4-2_en_Chap09_conduite_ed01-2014
Key left in the "Ignition on"
position
On 
opening
 
the
 
driver's
 
door
,  
an
 
alert

 
message
 
is
 
displayed,
 
ac
-
companied
 
by
 
an
 
audible
 
signal,
 
to

 
remind
 
you
 
that
 
the
 
key
 
is
 
still
 
in

 
the
 
ignition
 
switch
 
at
 
posi
-
tion
1 (Stop).
If
 
the
 
key
 
has
 
been
 
left
 
in
 
the
 
igni
-
tion switch at position 2 (Ignition
on),
 
the
 
ignition
 
will
 
be
 
switched
 
of

f   automatically   after   one   hour.
To
 
switch
 
the
 
ignition
 
back
 
on,
 
turn

 
the
 
key
 
to
 
position
 
1 (Stop)
,
then
 
back
 
to
 
position
 
2 (Ignition
on)

.Switching off the engine
F Stop   the   vehicle.
F  
With
 
the
 
engine
 
running
 
at
 
idle,
 
turn
 
the

  key   to   position   1.
F
 
Remove
 
the
 
key
 
from
 
the
 
ignition
 
switch.
F

 
T
o  
lock
 
the
 
steering
 
column,
 
turn
 
the
 
steering

  until   it   locks. Energy economy mode
After
 switching  of f  the  engine  (posi -
tion 1-Stop ),  for  a  maximum  of  30  min -
utes you can still use functions such
as
 
the
 
audio
 
and
 
telematic
 
system,
 
the
 
wipers,

 
dipped
 
beam
 
headlamps,
 
cour
-
tesy
  lamps,   ...
For
 
more
 
information,
 
refer
 
to
 
the

 
"Practical
 
information"
 
sec
-
tion,
 
under
 
"Energy
 
economy
 
mode".
T

o  
facilitate
 
unlocking
 
of
 
the
 
steer
-
ing
 
column,
 
it
 
is
 
recommended that

 
the
 
wheels
 
be
 
returned
 
to the

 
straight
 
ahead
 
position
 
before switching

  off   the   engine.
F
 
Check
 
that
 
the
 
parking
 
brake
 
is
 
cor
-
rectly
 
applied,
 
particularly
 
on
 
sloping ground.Never

 
switch
 
of
f  
the
 
ignition
 
be
-
fore
 
the
 
vehicle
 
is
 
at
 
a
 
complete
 
stop.

 
With
 
the
 
engine
 
of
f,  
the
 
braking

 
and
 
steering
 
assistance
 
systems

 
are
 
also
 
cut
 
of
f:  
risk
 
of
 
loss

  of   control   of   the   vehicle.
When you leave the vehicle,
keep
 
the
 
key
 
with
 
you
 
and
 
lock
 
the

  vehicle.
DRIVING

99
148 
C4-2_en_Chap09_conduite_ed01-2014
Moving off
F With your  foot  on  the  brake,  select  position
P or N.
F
 
Start
  the   engine.
If
 
this
 
procedure
 
is
 
not
 
followed,
 
there
 
is

 
an
 
audible
 
signal,
 
accompanied
 
by
 
a
 
message

  in   the   multifunction   screen.
F
 
With
 
the
 
engine
 
running,
 
press
 
the
 
brake

  pedal.
F
 
Release
 
the
 
parking
 
brake,
 
unless
 
it
 
is

  programmed   to   automatic   mode.
F

Select position
R, D or M.
F
 
Gradually
  release   the   brake   pedal.
The
  vehicle   moves   off   immediately.
If position N
 
is
 
engaged
 
inad
-
vertently
 
while
 
driving,
 
allow
 
the
 
engine

 
to
 
return
 
to
 
idle
 
then
 
en
-
gage
  position   D   to   accelerate.
When
 
the
 
engine
 
is
 
running
 
at
 
idle,

 
with
 
the
 
brakes
 
released,
 
if position

R, D or M
 
is
 
selected,
 
the

 
vehicle
 
moves
 
even
 
without
 
the

  accelerator   being   pressed.
When
 
the
 
engine
 
is
 
running,
 
never

 
leave
 
children
 
in
 
the
 
ve
-
hicle
  without   supervision.
When
 
carrying
 
out
 
maintenance
 
with

 
the
 
engine
 
running,
 
apply
 
the

 
parking
 
brake
 
and
 
select
 
po
-
sition P. A
 message

 
is
 
displayed
 
if
 
you
 
try
 
to
 move
 the  gear  lever  from  position  P
without   pressing   the   brake   pedal.
n

ever select position N while the
vehicle
  is   moving.
n

ever select positions P or R
unless
 
the
 
vehicle
 
is
 
completely
 
stationary

.
Sport and snow programmes
These two special  programmes  supple -
ment  the  automatic  operation  in  very  
specific

  conditions   of   use.
Sport programme "S"
F

Press button
"S",  
after
 
starting
 
the
 
engine.
The

 
gearbox
 
automatically
 
favours
 
a
 
dynamic

  style   of   driving.
S
 
appears
 
in
 
the
 
instrument
 
panel.
Snow programme "

T"
F

Press
button "T",  
after
 
starting
 
the
 
engine.
The

 
gearbox
 
adapts
 
to
 
driving
 
on
 
slip
-
pery
  roads.
This
 
programme
 
improves
 
starting
 
and
 
drive

  when   traction   is   poor.
T
 
appears
 
in
 
the
 
instrument
 
panel.
Return to automatic operation
F At any  time,  press  the  button  select -
ed  again  to  quit  the  programme  en -
gaged
 
and
 
return
 
to
 
auto-adaptive
 
mode.
Automatic operation
F Select position D for automatic
changing   of   the   six   gears.
The
 
gearbox
 
then
 
operates
 
in
 
auto-
adaptive

 
mode,
 
without
 
any
 
intervention
 
on

 
the
 
part
 
of
 
the
 
driver
.  
It
 
continuously
 
selects

 
the
 
most
 
suitable
 
gear
 
accord
-
ing
 
to
 
the
 
style
 
of
 
driving,
 
the
 
profile
 
of
 
the

  road   and   the   load   in   the   vehicle.
For
 
maximum
 
acceleration
 
without
 
touching

 
the
 
lever
,  
press
 
the
 
accelera
-
tor
 
pedal
 
down
 
fully
 
(kick
 
down).
 
The
 
gearbox

 
changes
 
down
 
automatically
 
or

 
maintains
 
the
 
gear
 
selected
 
until
 
the
 
maximum

  engine   speed   is   reached.
On
 
braking,
 
the
 
gearbox
 
changes
 
down
 
automatically

 
to
 
provide
 
efficient
 
engine
 
braking.
If you release the accelerator sharply

,
the
 
gearbox
 
will
 
not
 
change
 
to
 
a
 
higher
 
gear

  for   safety   reasons.
DRIVING

99
149 
C4-2_en_Chap09_conduite_ed01-2014
Manual operation
F Select position M for sequential
changing   of   the   six   gears.
F
 
Push
 
the
 
lever
 
towards
 
the
 
+
 
sign
 
to
 
change

  up   a   gear.
F
 
Pull
 
the
 
lever
 
towards
 
the
 
-
 
sign
 
to
 
change

  down   a   gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear

 
to
 
another
 
if
 
the
 
vehicle
 
speed
 
and
 
engine

 
speed
 
permit;
 
otherwise,
 
the
 
gearbox

 
will
 
operate
 
temporarily
 
in
 
au
-
tomatic
  mode.D
 
disappears
 
and
 
the
 
gears
 
engaged

 
appear
 
in
 
succes
-
sion
  in   the   instrument   panel.
If
 
the
 
engine
 
speed
 
is
 
too
 
low
 
or

 
too
 
high,
 
the
 
gear
 
selected
 
flashes

 
for
 
a
 
few
 
seconds,
 
then
 
the
 
ac
-
tual
  gear   engaged   is   displayed.
It
 
is
 
possible
 
to
 
change
 
from
 
position
 
D

(automatic)
 
to
 
position
 
M
 
(manual)
 
at
 
any

  time.
When
 
the
 
vehicle
 
is
 
stationary
 
or
 
mov
-
ing
 
very
 
slowly
,  
the
 
gearbox
 
selects
 
gear

  M1   automatically.
The
 
sport
 
and
 
snow
 
programmes
 
do
 
not

  operate   in   manual   mode.Invalid value during manual
operation
This  symbol  is  displayed  if  a  
gear

 
is
 
not
 
engaged
 
correctly
 
(selector between two posi

-
tions).
Stopping the vehicle
Before switching  of f  the  engine,  you  can
 engage  position  P or N to place the
gearbox
  in   neutral.
In
 
both
 
cases,
 
apply
 
the
 
parking
 
brake
 
to

 
immobilise
 
the
 
vehicle,
 
unless
 
it
 
is
 
programmed

  to   automatic   mode.
If the lever is not in position P,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or

 
approximately
 
45
 
seconds
 
after

 
the
 
ignition
 
is
 
switched
 
of
f,  
there

 
is
 
an
 
audible
 
signal
 
and
 
a
 
message

  appears.
F

Return
the lever to posi-
tion

P
;  
the
 
audible
 
signal
 
stops

 
and
 
the
 
message
 
dis
-
appears. You
  risk   damaging   the   gearbox:
-
 
if
 
you
 
press
 
the
 
accelera
-
tor
 
and
 
brake
 
pedals
 
at
 
the
 
same

  time,
-
 
if
 
you
 
force
 
the
 
lever
 
from
 
position P

to another position
when
  the   battery   is   flat.
When
 
the
 
ignition
 
is
 
on,
 
the

 
lighting
 
of
 
this
 
warning
 
lamp,

 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
multifunction

 
screen,
 
indicates
 
a
 
gear
-
box   malfunction.
In  
this
 
case,
 
the
 
gearbox
 
switches
 
to
 
back-up

 
mode
 
and
 
is
 
locked
 
in
 
3rd
 
gear

.  
Y
ou  
may
 
feel
 
a
 
substantial
 
knock
 
when

 
changing
 
from
 
P
to R  
and
 
from
 
N

to R.  This  will  not  cause  any  damage  to  the
  gearbox.
Do
 
not
 
exceed
 
60
 
mph
 
(100
 
km/h),
 
lo
-
cal
  speed   restrictions   permitting.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

  a   qualified   workshop.
This
 
warning
 
lamp
 
may
 
also
 
come
 
on
 
if
 
a

  door   is   opened.
Operating fault
To reduce fuel  consumption  when
 stationary  for  long  periods  
with

 
the
 
engine
 
running
 
(traf
-
fic
 
jam...),
 
position
 
the
 
gear
 
le
-
ver at
N  
and
 
apply
 
the
 
parking
 
brake,

 
unless
 
it
 
is
 
programmed
 
in

  automatic   mode.
When
 
driving

 
through

 
flooded

 
roads

 
or

 
crossing

 
a

 
ford,

 
drive

 
at

 
walking

 
speed.
DRIVING