boot Citroen C4 PICASSO 2009 1.G Owner's Guide

Page 188 of 337

153
IX
D R I V I N G
PNEUMATIC SUSPENSION

Grand
C4 Picasso
C4 Picasso
The rear pneumatic suspension en-
hances driving comfort by maintain-
ing a constant body height whatever
the vehicle load. Operation
- If there is an increase in vehi-
cle load, a sinking of the rear of
the vehicle is detected and the
pneumatic springs infl ate in or-
der to compensate for the extra
weight.
- If there is a decrease in load, a rising of the rear of the vehicle is
detected and so the pneumatic
springs defl ate to return the ve-
hicle to its nominal height.
- If the vehicle has been unused for a long period, the pneumatic
springs may infl ate if necessary
when you unlock or open a door,
so as to return the vehicle to its
nominal height.
If you do not reactivate the system
manually, the automatic correction
will be activated as soon as the ve-
hicle starts to move. During the cor-
rection, the service warning lamp
lights up and a message on the
screen reminds you not to exceed
10 km/h (6 mph).
The automatic correction does not
function if the doors or the boot are
open.
The automatic correction operates
even if your vehicle is in power
economy mode. Activation/Deactivation
The automatic correction can be de-
activated:

 press on the button B for approx-
imately two seconds,

 release the button when you
hear a beep. Deactivation is con-
fi rmed by the lighting of the indi-
cator lamp on the button B .

In the event of the system mal-
functioning, alert messages,
always in association with the
service warning lamp, will dis-
play in the instrument panel .
Consult a CITROËN dealer.
It is essential that you should deactivate
the system in the following instances:
- working under the vehicle,
- changing a wheel,
- transporting the vehicle on a
truck or on a boot.
To reactivate the automatic correction:

 press again on the button B for
approximately two seconds,

 release the button when you hear
a beep. Activation is confi rmed
by the extinction of the indicator
lamp on the button B .

Page 189 of 337

154
IX
D R I V I N G
Loading/unloading
assistance

Grand
C4 Picasso
C4 Picasso
The pneumatic suspension has an
additional function associated with
it: the possibility to raise or lower
the height of the rear of the vehicle
when stationary, in order to facilitate
loading/unloading of the boot. Increasing the height of the boot
fl oor

 Press continuously at the top of
the control A , which is located in
the boot, on the left-hand side.
This action will be accompanied by
an audible signal. You can stop the
movement at any time by releasing
the control.
3 beeps will confi rm that the move-
ment has gone as far as it can.

Returning to the
normal
height

 Press briefl y twice at the bottom
of the control A .
Decreasing the height of the boot
fl oor

 Press continuously at the bottom
of the control A .
This action will be accompanied by
a sound signal. You can stop the
movement at any time by releasing
the control.
3 beeps will confi rm that the move-
ment has gone as far as it can.
Returning to the
normal
height

 Press briefl y twice at the top of
the control A .
Driving with the boot in a
low position may damage
the components located un-
der the bodyshell.

Special features
- If you start the vehicle without having returned it to the normal
height, automatic correction will
activate as soon as the vehicle
starts to move. During the cor-
rection, the service warning lamp
lights up and a message on the
screen reminds you not to ex-
ceed 10 km/h (6 mph).
- The loading assistance does not function in the following instances:
- If the button B is lit up,
- in power economy mode,
- when you fi rst use the function, press for two seconds on the
control A to initialise the system.
All subsequent actions will be
followed immediately by the de-
sired results.

Page 199 of 337

165
XI
P R A C T I C A L I N F O R M A T I O N
PUNCTURE REPAIR KIT Using the kit
The kit is located in the boot under
the fl oor or under the fl ap in the sec-
ond row left-hand passenger foot-
well (open by turning the screw a
quarter of a turn).
 Tick the wheel to be repaired
on the speed limitation sticker
enclosed then affi x the sticker
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.

 Switch off the ignition.

 Clip the bottle 1 on the compres-
sor 2 .

 Check that the switch A is tilted
to position "0" .

 Connect the pipe of the bottle 1
to the valve of the tyre to be re-
paired.

 Unwind the pipe of the compres-
sor 2 fully before connecting it to
the bottle.

 Connect the compressor's elec-
tric plug to the vehicle's 12 V
socket.

 Start the vehicle and leave the
engine running.
Complete system consisting of a
compressor and a bottle of sealant
which permits
temporary repair of
the tyre so that you can drive to the
nearest garage.
This repair kit is available from
CITROËN dealers.
It is designed to repair holes of a
maximum diameter of 4 mm, locat-
ed exclusively on the tyre tread or
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.

Page 212 of 337

177
XI
P R A C T I C A L I N F O R M A T I O N
Rear lamps
(Grand C4 Picasso)

1. Direction indicators
(PY21 W)

2. Stoplamps (P21 W)

3. Reversing lamp
(P21 W)

4. Sidelamps (diodes)
For this type of lamp, contact a CITROËN dealer. Changing lamps

 Identify the bulb that is faulty.

 With the tailgate open, undo the
3 screws located on the side of
the lens unit and pull it rearwards
to detach.

 Disconnect the connector linking
the lens unit to the boot. Do not
disconnect the diodes.

 Remove the seal.

 Remove the bulb-holder.

 Replace the bulbs.
To remove a bulb, rotate it a quarter turn.
To fi t the bulb, rotate it a quarter turn in the other direction.

 Reposition the bulb-holder.

 Put back the seal.

 Reconnect the connector to the
lens unit.

 Stow the harness in the opening
provided in the body.

 Refi t the lens unit to the body
and do up the 3 screws.

Number plate lamps (W 5 W)

 Insert a thin screwdriver into one
of the external holes of the lens.

 Push it outwards to unclip it.

 Remove the lens.

 Change the faulty bulb.

Page 213 of 337

178
XI
P R A C T I C A L I N F O R M A T I O N
Third brake lamp with bulb
(W 5 W)

 With the boot open, detach the
interior trim.

 Undo the nuts.

 Using a thin screwdriver, detach
the 3 retaining lugs.

 Remove the lamp via the exte-
rior of the tailgate.

 Remove the bulb-holder.

 Change the faulty bulb(s).
To refi t, carry out these operations in
reverse order.

Third brake lamp (diodes)
For the replacement of this type of
diode lamp, contact a CITROËN
dealer. Interior lighting
Interior lamp (1/W 5 W)
Detach the cover of the interior lamp

1 with a thin screwdriver, close to the
button, to access the faulty bulb.
Map reading lamps (2/W 5 W)
Detach the cover of the interior lamp.
To access the faulty bulb, detach the
partition for the reading lamp 2 con-
cerned, as necessary. Boot lamps (W 5 W)
Detach the unit by pushing it rear-
wards.
Torch (Krypton 3.6 V)

 Open the tab.

 Push with a fl at screwdriver in
the hole under the tab and re-
cover the bulb unit.

 Open the bulb unit fully to change
the bulb.

Page 214 of 337

178
XI
P R A C T I C A L I N F O R M A T I O N
Third brake lamp with bulb
(W 5 W)

 With the boot open, detach the
interior trim.

 Undo the nuts.

 Using a thin screwdriver, detach
the 3 retaining lugs.

 Remove the lamp via the exte-
rior of the tailgate.

 Remove the bulb-holder.

 Change the faulty bulb(s).
To refi t, carry out these operations in
reverse order.

Third brake lamp (diodes)
For the replacement of this type of
diode lamp, contact a CITROËN
dealer. Interior lighting
Interior lamp (1/W 5 W)
Detach the cover of the interior lamp

1 with a thin screwdriver, close to the
button, to access the faulty bulb.
Map reading lamps (2/W 5 W)
Detach the cover of the interior lamp.
To access the faulty bulb, detach the
partition for the reading lamp 2 con-
cerned, as necessary. Boot lamps (W 5 W)
Detach the unit by pushing it rear-
wards.
Torch (Krypton 3.6 V)

 Open the tab.

 Push with a fl at screwdriver in
the hole under the tab and re-
cover the bulb unit.

 Open the bulb unit fully to change
the bulb.

Page:   < prev 1-10 11-20 21-30 31-40