reset Citroen C4 PICASSO 2009 1.G Owner's Manual

Page 21 of 337

24
I
I N S T R U M E N T S a n d C O N T R O L S
MONOCHROME INSTRUMENT PANEL
MULTIFUNCTION SCREEN A
The instrument panel groups all the driving and comfort information at the centre of the dashboard.
Central display

1. Rev counter

2. Electronic gearbox or automatic
gearbox selector position and
gear

3. Electronic gearbox or automatic
gearbox "Foot on brake" warning
lamp

4. Speedometer

5. Cruise control or speed limiter
setting

6. Fuel gauge
7. Trip mileage recorder

8. Multifunction screen A

9. Total mileage recorder
In this zone, the following infor- mation appears in succession
when the ignition is switched on:
- maintenance indicator,
- engine oil level indicator,
- total mileage recorder. Control buttons

A. Lighting rheostat (available day
and night)

B. Trip mileage recorder reset

C. Personalisation of the instru-
ment panel (display of desired
information)

D. CHECK (list of alerts)

Page 22 of 337

25
I
I N S T R U M E N T S a n d C O N T R O L S
TWO - TONE INSTRUMENT PANEL
MULTIFUNCTION SCREEN C
The instrument panel groups all the driving and comfort information at the centre of the dashboard.
Central display

1. Rev counter

2. Electronic gearbox or automatic
gearbox selector position and
gear

3. Electronic gearbox or automatic
gearbox "Foot on brake" warning
lamp

4. Speedometer

5. Cruise control or speed limiter
setting

6. Fuel gauge
7. Trip mileage recorder

8. Multifunction screen C

9. Total mileage recorder
In this zone, the following infor- mation appears in succession
when the ignition is switched on:
- maintenance indicator,
- engine oil level indicator,
- total mileage recorder. Control buttons

A. Lighting rheostat (available day
and night)

B. Trip mileage recorder reset

C. Personalisation of the instru-
ment panel (display of desired
information)

D. COLOUR (choice of background
colour ranging from white to
blue)

Page 23 of 337

26
I
I N S T R U M E N T S a n d C O N T R O L S
NAVIDRIVE INSTRUMENT PANEL
NAVIDRIVE MULTIFUNCTION SCREEN
The instrument panel groups all the driving and comfort information at the centre of the dashboard.
Central display

1. Cruise control or speed limiter
setting

2. Speeometer

3. NaviDrive multifunction screen
(see "NaviDrive instructions")

4. Rev counter

5. Electronic gearbox or automatic
gearbox "Foot on brake" warning
lamp

6. Fuel gauge

7. Electronic gearbox or automatic
gearbox selector position
8. Trip mileage recorder

9. Total mileage recorder
In this zone, the following infor- mation appears in succession
when the ignition is switched on:
- maintenance indicator,
- engine oil level indicator,
- total mileage recorder. Control buttons

A. Personalisation of the instru-
ment panel (display of desired
information)

B. COLOUR (choice of background
colour ranging from white to
blue)

C. Lighting rheostat (available day
and night)

D. Trip mileage recorder reset

Page 30 of 337

31
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator
System which informs the driver
when the next service is due, in
accordance with the manufacturer's
servicing schedule.
The point at which the service is due
is calculated from the last indicator
zero reset. It is determined by two
parameters:
- the distance travelled,
- the time elapsed since the last service. 5 seconds after the ignition is switched
on,
the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances.
Less than 620 miles (1 000 km)
remain before the next service
is due

Example: 560 miles (900 km) re-
main before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates: Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation. The
spanner remains on to indicate that
a service must be carried out soon. 5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation.
The
spanner remains lit .
More than 620 miles (1 000 km)
remain before the next service
is due
For 5 seconds after the ignition is
switched on, the spanner symbo-
lising the service operations comes
on. The distance recorder display
line indicates the distance remaining
before the next service is due.

Example: 4 800 miles/km remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
The distance remaining may be
weighted by the time factor, depen-
ding on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

Page 31 of 337

32
I
I N S T R U M E N T S a n d C O N T R O L S

Maintenance indicator zero
reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to
locate the dipstick and the oil fi ller
cap on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.

Page 32 of 337

32
I
I N S T R U M E N T S a n d C O N T R O L S

Maintenance indicator zero
reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to
locate the dipstick and the oil fi ller
cap on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.

Page 33 of 337

33
I
I N S T R U M E N T S a n d C O N T R O L S

Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other
period since it was reset to zero by
the driver.

 With the ignition on, press the
button until zeros appear. Lighting rheostat
System for manual adjustment of the brightness of the instruments and controls in relation to the exteriorbrightness.
Activation
When the lights are on:
 press the button to change the brightness of the instruments and controls,
 when the lighting reaches the minimum setting, release the button, then press again to in-crease it,
or
 when the lighting reaches the maximum setting, release the button, then press again to re-duce it,
 when the lighting reaches the level of brightness required, re-lease the button.
Deactivation
When the lights are off, or in day mode on vehicles fi tted with daytime lights, pressing the button does not have any effect.

Page 41 of 337

41
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current
information concerning the route
travelled (range, consumption...).
Monochrome screen A Data displays

 Press the control for more than
two seconds to reset to zero the
distance travelled, the average
consumption and the average
speed.
Zero reset
The trip computer provides the fol-
lowing information: - range,
- current consumption,
- distance travelled,
- average consumption,
- average speed.

 The next press then returns you
to the normal display.

 Press the button, located at the
end of the wiper
stalk , to display
the various items of trip compu-
ter data in succession.

Page 42 of 337

42
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current in-
formation concerning the route trav-
elled (range, consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper
stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with:


Page 271 of 337

233
07
A few defi nitions
Range: displays the distance which can be travelled with the remaining fuel detected in the tank, based on the average consumpt ion over the last few miles (kilometres). This displayed value may vary signifi cantly following a change in the vehicle speed or the relief of the route. When the range falls below 20 miles (30 km), dashe s are displayed. After fi lling with at least 5 litres of fuel, the range is recalculated and is displayed as soon as it exceeds 60 miles (100 km). If, whilst driving, dashes are displayed continuou sly in place of digits, contact a CITROËN dealer. If, whilst driving, dashes are displayed continuously in place of digits, contact If, whilst driving, dashes are displayed continuously in place of digits, contact
Current fuel consumption: only calculated and displayed above 20 mph (30 km/h).
Average fuel consumption: this is the average fuel condumption since the last trip recorder zero reset.
Distance travelled: calculated since the last trip computer zero reset.
Distance remaining to the destination: calculated with reference to the fi nal destination entered by the user. If guidance is activated, the navigation system calculates it as a current value.
Average speed: this is the average speed calculated since the last trip computer zero reset (ignition on).
TRIP COMPUTER
With tab "1" (route 1): 

Page:   1-10 11-20 next >