third row seats Citroen C4 PICASSO 2009 1.G Owner's Manual

9
F A M I L I A R I S A T I O N
Fold the concertina plates ( 1 2 3 ) ar-
ranged on each of the third-row seats.
Pull on the black belt F , located on the
seat backrest.

 64
Before moving the third-row seats,
do not forget to lock in the rigid
plates fi rst (located at the base of the
second-row seat backrests).
Installing the seats
Put the three sections of the concertina
plates ( 1 2 3 ) to their vertical position,
then pull on the red belt G .
Before moving the third-row seats, re-
turn the rigid plates to the upright posi-
tion and lock them. Pull on control
E , located at the top of
the second-row seats backrest.

 63
I N T E R I O R
Stowing the seats Access to third-row seats
Do not leave objects either on or un-
derneath the second-row seats when
you are folding them. THIRD - ROW SEATS – GRAND C4 PICASSO

10
F A M I L I A R I S A T I O N
Folding the seats
From the boot - whilst loading,
for example (Grand C4 Picasso)
Take care to attach the third-row pas-
senger seat belts on the rings provided
for this purpose.

Do not attach the belts on the an-
choring points marked with a red
cross (see illustration above).

Stowing the tongue of the third-row
seat belt
SECOND - ROW SEATS

 119
Requirements for third-row
passenger seat belts
From outside

 Pull fi rmly upwards on strap C , as
indicated by the red arrow, to unlock
the seat; maintain the pressure until
the seat is fully folded.

 Slide latch A of the plate down-
wards, to unlock it.

 Return the plate to the upright posi-
tion, then slide latch A upwards to
lock it.
Before deploying the rigid plates, check
that the second row seats are slid as far
back as possible.

 62
I N T E R I O R
THIRD - ROW SEATS – GRAND C4 PICASSO
Having fi rstly folded the third-row
seats.

 Pull on control D to unlock the re-
quired seat.
Repositioning the seats
Return the rigid plates of the second-
row seats to their initial (upright) posi-
tion and lock them in position (Grand
C4 Picasso).
Raise the backrest and push it back-
wards until it locks in position. Rigid plate (Grand C4 Picasso)
A rigid plate is attached to each sec-
ond-row seat backrest.
Unlocking/Locking the rigid plate

62
III
C O M F O R T
SECOND ROW SEATS (GRAND C4 PICASSO)
Each seat can be folded onto the
fl oor to form a fl at surface, thus en-
abling you to modify your vehicle’s
interior space.
Folding the seat
From the exterior

 Pull fi rmly upwards on strap C ,
as indicated by the red arrow, to
unlock the seat; keep pulling un-
til the seat is fully folded.

 Push the backrest slightly for-
wards, so that the backrest
pivots, folding onto the seat
base. The assembly will then
lower onto the fl oor. From the boot
(when loading, for example)
You can fold the second-row seat(s)
from the boot, having fi rst folded the
third-row seats.

 Pull on the strap D to unlock the
chosen seat, push the backrest
gently forwards.
To prevent any damage to the mechanism, the strap D unclips
under excessive force. Simply
reclip it to render the system
operational.
Repositioning the seat

 Return the second-row seat bas-
es to their initial position and lock
them in that position.

 Raise the backrests and push
them rearwards so that they lock
in position.
Before moving the third-row seats,
return the second-row rigid panels to
their initial position and lock them.
Emergency exit: should the fi rst
system fail (strap C ), the strap D is
available for use by third-row pas-
sengers to accelerate their exit.

Always supervise any move-
ments of seats by children. Rigid panel
Each second-row seat backrest has
a rigid panel attached.
This panel enables you:
- to have a continuous load sur-
face in the boot, whatever the
positions of the seats,
- to avoid having objects sliding under the second-row seats.
Unlocking/Locking the rigid panel

 Slide the latch 1 on the plate
downwards, to unlock.

 Return the panel to the upright
position, then slide the latch 1
upwards, to lock.
Before deploying the rigid panels,
check that the second-row seats are
in the fully back position.
5-seater confi gurations do not have
these rigid panels.

63
III
C O M F O R T
"Cinema seat" position
This position allows you to free up
space between the fi rst row and the
second row.
Pull the control E under the seat.
This position is only possible with
the lateral seats. Access to the third row seats
The third-row seats can be accessed
via the lateral second-row seats.

 Pull the control E . The seat un-
locks and the seat base comes
up against the backrest.

 Hold the control E in the raised
position, pushing forwards. The
whole seat slides towards the
front seat.
Space becomes free behind the
seat, the third-row passengers can
get to their seats. Exit from the third row seats

 Hold the control E in the raised
position. The seat unlocks and
the seat base comes up against
the backrest.

 Push the seat backrest, still hold-
ing the control E in the raised po-
sition.
If the table on the back of the fi rst-
row seat is down, close it to enable
this operation.
Repositioning the seat,
from the exterior,
with the door open
If there are passengers seated in
the third row:

 manually return the assembly as
far as possible rearwards; the
seat does not return as far as
the maximum rearwards position
so as to retain leg space for the
third-row passengers,

 fold the seat base.

64
III
C O M F O R T
THIRD ROW SEATS (GRAND C4 PICASSO)
Concertina boards
Two rigid concertina boards, which
cannot be separated from the ve-
hicle, cover the 2 third-row seats,
when these are in the folded
position.
Folding the concertina boards
Pull on the control, the 3 sections of
the board will fold like a concertina.
When the third-row seats are up-
right, these concertina boards can
be left either:
- fl at behind the seats,
- in the vertical position,
thereby leaving a storage area
available. Unfolding the seat

 Return the second-row rigid
panels to their initial position and
lock them.

 Having folded your concertina
board, pull on the control F lo-
cated behind the seat backrest.
The backrest pivots rearwards,
pulling the seat base with it. The
seat locks in the open position.
Repositioning the seat

 Return the second-row rigid
panels to their initial position and
lock them.

 Lower the head restraints.

 Correctly position the concertina
board vertically behind the seat. Before moving the third-row seats,
return the rigid plates of the sec-
ond-row seats to the upright posi-
tion and lock them.
Do not try to fold a third-row seat
that has not fi rst had the backrest
fully locked in place.
Do not leave objects either on or
underneath the seat bases of the
third-row seats when you are fold-
ing them.
Do not leave your hand on the con-
trol
G as you fold the seats, as you
risk trapping your fi ngers.

 Pull on the control G , located at
the bottom of the seat backrest.
The seat unlocks.

 Next push the backrest gently
forwards. The backrest pivots,
folding onto the seat base. The
seat base then folds into the
stowage area provided for that
purpose.

 Reposition the concertina boards
over the folded seats.

100
VI
L A Y O U T
MODUBOX (C4 PICASSO)
Equipment for use both inside the
vehicle and away from the vehicle.
It is composed of a shopping trol-
ley and a fl exible bag (isotherm on
some versions) which can be used
independently of each other depen-
ding on your needs (by detaching
the fastenings on each side at the
top and bottom).
To use

 Unhook the red strap to free the
Modubox.

 Unhook the black strap then press
on the round buttons on either side
of the Modubox simultaneously to
deploy it. Use of the Modubox outside
the vehicle
Stowage inside the vehicle

 Perform the operations in reverse
to fold and stow inside the vehicle.

 If you have used your Modubox
away from the vehicle, take care to
reposition it correctly in the housings provided for this purpose.
BAG HOOK
LUGGAGE-COVER BLIND (GRAND C4 PICASSO)
Position 1
5-seat confi guration; installed be-
hind the second-row seats, with the
third-row seats folded away.

 Press on the recess on the left
hand side of the Modubox to
raise (or lower) the handle.
Located on the left-hand interior wall
of the boot, this permits the securing
of shopping bags.
Installing the roller

 Position the left-hand end of the
blind roller in notch A .

 Compress the right-hand end of
the roller and place it in notch B .

 Unroll the blind until it reaches
the boot pillars.

 Insert the guides of the blind into
the rails on the pillars.

Removing the roller


Perform these operations in reverse
order.

101
VI
L A Y O U T
The roller has a moving fl ap to avoid
interference with the second-row
passengers when the seats are in
the "reclined" position.
 Engage the lug on the left of the
roller in notch C .

 Pass the right-hand side above
the third-row armrest.

 Engage the lug in notch D .

 Pull the seat belt(s) so that they
will deploy without locking.

 Unroll the blind and engage the
guides into the rails on the pillars.

 Lock the seat(s) in position.

Installing the roller

 Roll up the blind, then remove
the roller from its initial position.

 Position the roller, with the blind pull
bar uppermost, fl ap downward.

 Fold the concertina boards.
Removing the roller

 Push the fl ap towards the seat
backrest.

 Lift the concertina board by grab-
bing it at the side, then position it
vertically.

 Unlock the seat by pulling the
strap E .

 Push the backrest towards the
front.

 Proceed in reverse order to in-
stalling. Position 3
7-seat confi guration; stowed behind
the third row seats when these are
folded away.

Installing the roller

 Fold the concertina board.

 Position the roller, with the blind pull
bar uppermost, fl ap downward.

 Engage the lug on the left of the
roller in notch C .

 Pass the right-hand side above
the third-row armrest.

 Engage the lug in notch D .

Removing the roller

 Proceed in reverse order to in-
stalling.
Position 2
7-seat confi guration; installed behind
the third-row seats when these are
folded away. This position conceals
objects stowed in the boot from out-
side view.
The blind can only be stored when
the seats are folded away.
You can position the concertina board
vertically to lodge a bulkier object in
the boot well.

102
VI
L A Y O U T
HIGH CARGO NET (GRAND C4 PICASSO)
This enables you to maximise the
vehicle’s loadspace.
It retains objects, preventing them
from sliding towards the front of the
passenger compartment.

You insert it under the roller of the
luggage-cover blind, securing it
on the third-row side mouldings. Position 1
5-seat confi guration; installed behind
the second row.

Installing the roller

 Remove the protective covers
located under the blind roller
notches.

 Position the roller under that of
the luggage-cover blind.

 Raise the fl ap on the blind, posi-
tioning it on top of the blind.

 Deploy the net, passing it between
the rollers and the seats.

 Pull the net upwards.

 Anchor it to the roof by means of
the fi xing points (after you have
removed their covers).

Removing the roller

 Perform these operations in re-
verse order. Position 2
2-seat confi guration; installed behind
the fi rst row.

Removing the roller

 Carry out these operations in
reverse order.

Installing the roller

 With the second-row seats folded
away, remove the covers of the
Isofi x anchoring points located on
the seat backrests.

 Secure the roller on the Isofi x
anchoring points.

 Deploy the net and pull it upwards.

 Anchor it to the roof by means of
the fi xing points (after you have
removed their covers).

100
VI
L A Y O U T
MODUBOX (C4 PICASSO)
Equipment for use both inside the
vehicle and away from the vehicle.
It is composed of a shopping trol-
ley and a fl exible bag (isotherm on
some versions) which can be used
independently of each other depen-
ding on your needs (by detaching
the fastenings on each side at the
top and bottom).
To use

 Unhook the red strap to free the
Modubox.

 Unhook the black strap then press
on the round buttons on either side
of the Modubox simultaneously to
deploy it. Use of the Modubox outside
the vehicle
Stowage inside the vehicle

 Perform the operations in reverse
to fold and stow inside the vehicle.

 If you have used your Modubox
away from the vehicle, take care to
reposition it correctly in the housings provided for this purpose.
BAG HOOK
LUGGAGE-COVER BLIND (GRAND C4 PICASSO)
Position 1
5-seat confi guration; installed be-
hind the second-row seats, with the
third-row seats folded away.

 Press on the recess on the left
hand side of the Modubox to
raise (or lower) the handle.
Located on the left-hand interior wall
of the boot, this permits the securing
of shopping bags.
Installing the roller

 Position the left-hand end of the
blind roller in notch A .

 Compress the right-hand end of
the roller and place it in notch B .

 Unroll the blind until it reaches
the boot pillars.

 Insert the guides of the blind into
the rails on the pillars.

Removing the roller


Perform these operations in reverse
order.

100
VI
L A Y O U T
MODUBOX (C4 PICASSO)
Equipment for use both inside the
vehicle and away from the vehicle.
It is composed of a shopping trol-
ley and a fl exible bag (isotherm on
some versions) which can be used
independently of each other depen-
ding on your needs (by detaching
the fastenings on each side at the
top and bottom).
To use

 Unhook the red strap to free the
Modubox.

 Unhook the black strap then press
on the round buttons on either side
of the Modubox simultaneously to
deploy it. Use of the Modubox outside
the vehicle
Stowage inside the vehicle

 Perform the operations in reverse
to fold and stow inside the vehicle.

 If you have used your Modubox
away from the vehicle, take care to
reposition it correctly in the housings provided for this purpose.
BAG HOOK
LUGGAGE-COVER BLIND (GRAND C4 PICASSO)
Position 1
5-seat confi guration; installed be-
hind the second-row seats, with the
third-row seats folded away.

 Press on the recess on the left
hand side of the Modubox to
raise (or lower) the handle.
Located on the left-hand interior wall
of the boot, this permits the securing
of shopping bags.
Installing the roller

 Position the left-hand end of the
blind roller in notch A .

 Compress the right-hand end of
the roller and place it in notch B .

 Unroll the blind until it reaches
the boot pillars.

 Insert the guides of the blind into
the rails on the pillars.

Removing the roller


Perform these operations in reverse
order.