warning Citroen C4 PICASSO DAG 2009 1.G User Guide

30
I
I N S T R U M E N T S a n d C O N T R O L S Airbags If this comes on, it indicates
the occurrence of a fault in
one of the airbag or seat belt
pretensioner systems.
Maximum coolant temperature
If this comes on, it indicates
that the temperature in the
cooling system is too high.
Stop the vehicle as soon as
it is safe to do so.
Low fuel level When the tank is full, all the
bars are lit up.
If the fuel low warning lamp comes on
accompanied by an audible signal and
a message on the multifunction screen,
there are approximately 7 litres of fuel
remaining in the tank and 2 or 3 bars
fl ash in the instrument panel.
When the last bar goes out, there
are approximately 2 litres of fuel
remaining in the tank.
A control located on the panel to the
left of the steering wheel allows you
to open the fuel fl ap from inside the
vehicle.
Battery charge If this comes on, it indi-
cates the occurrence of a
fault in the battery charging
circuit (dirty or loose termi-
nals, slack or cut alternator
belt, ...). Door open
A door, the boot or the rear
screen is open:
- if the speed is below 6 mph (10 km/h), this warning lamp comes on continuously.
- if the speed is higher than 6 mph (10 km/h), this warning lamp comes on
continuously, accompanied by an audi-
ble signal.
Seat belt not fastened/
unfastened
This warning lamp informs
you if the driver’s or front
passenger’s seat belt is
not fastened (depending
on model), and if the front
passenger’s (depending on
model) or the second row
passengers’ seat belts are
unfastened. The lit up positions rep-
resent those whose seat belts are
not fastened/unfastened. Seat belts unfastened during the
journey:
- the point corresponding to the seat
position with seat belt unfastened
lights up between 0 and 20 km/h.
Above 20 km/h (approx. 12 mph),
it fl ashes accompanied by an audi-
ble signal for around 120 seconds.
The audible signal stops when the
ignition is switched off or if a door
is opened.
Depending on model, the front pas-
senger seat may be fi tted with a
presence sensor; the correspond-
ing warning lamp will only come on
if the seat is occupied and the seat
belt not fastened.
Driver’s or front passenger’s seat belt
not fastened with presence sensor:
- the warning lamp lights up be-
tween 0 and 20 km/h. Above
20 km/h (approx.12 mph), it
fl ashes accompanied by a mes-
sage on the multifunction screen
and an audible signal for around
120 seconds.
Second row rear passengers’ or
front passenger’s seat belt not fas-
tened without presence sensor:
- when the ignition is switched on, the points corresponding to the seat po-
sitions with seat belts not fastened
remain lit up for 30 seconds.

47
III
C O M F O R T
MANUAL AIR CONDITIONING
A. DRIVER’S CONTROL PANEL
1. Adjustment of the air blower speed
The air blower adjustment only op-
erates when the engine is running.
To adjust the air fl ow, press on
button 1 :
to increase the fl ow of air,
to decrease the fl ow of air.
The level of air fl ow is shown by the pro-
gressive lighting of the warning lamps
depicting the ventilator blades 1 .
By reducing the fl ow to minimum,
you deactivate the air conditioning
system (OFF).
To achieve an agreeable level of
comfort in the passenger compart-
ment, you should not leave this
control too long in the OFF position.
2. Adjustment of the air
distribution

 Press on button 2 to make the
display scroll through the different
types of air distribution.
The air distribution chosen
is shown by the lighting of
the corresponding warning
lamps on the display 2.
3. Mode of adjustment of temperature for the
passenger

 Press on button 3 to have inde-
pendent passenger control of
cabin air temperature. The warn-
ing lamp goes out.
While the passenger is adjusting
temperature,the warning lamp lights
up. 4. Air recirculation
This control is for isolating disagree-
able odours or fumes coming from
outside.

 Press on button 4 , to exclude
entry of outside air. The warning
lamp lights up.
This should be cancelled as soon as possible to permit renewal of
cabin air and to prevent misting.

 Press again on button 4 , to de-
activate air recirculation.
5. Air conditioning
The air conditioning can only oper-
ate when the engine is running. The
air blower control (adjusting the fl ow
of air) has to be activated in order for
air conditioning to be obtained.

 Press on button 5 . The warning
lamp lights up.
To be effective, the air condi-
tioning should be operated only
with the windows closed.
If your vehicle is not equipped with
air conditioning, you will have the
same control panel but without the

A/C button.

48
III
C O M F O R T
6. Demisting/defrosting of the rear screen
This operates only if the engine is
running.

 Press on button 6 to activate/de-
activate the electric demisting/
defrosting of the rear screen and
the exterior rear view mirrors. The
warning lamp lights up.
7. Rapid Demisting/ Defrosting of front and
rear windows and rear
view mirrors

 Press on button 7 . The warning
lamp lights up.
This function simultaneously acti-
vates:
- front demisting/defrosting,
- optimum fl ow of air,
- recirculation prohibition,
- demisting/defrosting of rear view mirrors and heated rear screen,
- air conditioning, if necessary.
To stop the function, press again on
button 7 . 8. Adjustment of the air
blower temperature
This control is for adjusting the tem-
perature of the air in the passenger
compartment. It can be used in cold
weather as well as in hot weather,
provided the air conditioning is
active.
The adjustment of the temperature is
continuous and progressive starting
from one side.
B. PASSENGER’S CONTROL PANEL
Adjustment of temperature

 Press on button 9 to take over
control of the temperature. The
warning lamp lights up.

 Rotate button 10 to adjust your
temperature.
The adjustment of the temperature is
continuous and progressive starting
from one side.
The demisting/defrosting
switches off automatically
to prevent excessive con-
sumption of power.

49
III
C O M F O R T
AUTOMATIC AIR CONDITIONING
A. DRIVER’S CONTROL PANEL
1. Automatic comfort regulation
A press on this button, con-
fi rmed by the display of the

A/C warning lamp and of

AUTO on the screen, pro-
vides automatic control, at the tem-
perature selected, of all the following
5 functions:
- air fl ow,
- cabin temperature, on left hand side and right hand side,
- air distribution,
- air conditioning,
- automatic air recirculation. For this facility to operate, it is rec-
ommended to keep all the air vents
open.
Using the
AUTO mode will prevent
misting inside the vehicle in cold or
humid weather.
When starting from cold, in order to
avoid a rush of cold air, the blower
attains its optimum level progres-
sively. 2. Adjustment of temperature
To display the desired temperature,
press button:
-
- to decrease the temperature,
- + to increase the temperature.
An adjustment around 21 will pro-
vide an agreeable temperature level.
However, depending on your prefer-
ence, anything between 18 and 24
is quite normal.
For optimum comfort, it is recom-
mended to avoid an adjustment dif-
ference greater than 3 between right
and left.
Actual temperatures experienced in
the passenger compartment are de-
pendent on external factors and for
this reason might not be identical to
those displayed.
On entering the vehicle, the inside
temperature may be much colder (or
hotter) than would be comfortable. It
serves no purpose to alter the tem-
perature displayed in an attempt to
attain your preference more rapidly.
The system automatically does all in
its power to make up the difference
in temperature as soon as possible.

Manual resumption of one or
more functions
It is possible to adjust each of the
functions 3, 4 , 6 and 10 manually.
The display of the "AUTO" function
will then go off.

Resumption by the driver of the
adjustment of cabin temperatures
(for the front and rear passengers).

A long press on the "AUTO" button
will realign the temperature for all
passengers with the preferences of
the driver.

50
III
C O M F O R T
3. Adjustment of the air blower speed
The air blower operates only when
the engine is running (except when
the REST function is activated).
To adjust the fl ow of air, press on the
button:
to increase the air fl ow,
to decrease the air fl ow (this
button also has the REST
function).
The level of air fl ow is indicated on
the display by the progressive fi lling
of the ventilator blades.
If you place the air blower on posi-
tion 0 , the system is deactivated.
The air blower display will be empty,
with the indication OFF.

Function for retaining
ventilation with the engine
switched off

The REST function is availa-
ble when you switch on the ignition
and when you stop the engine.
This function allows you to retain
ventilation in the passenger com-
partment for a few minutes, even
with the engine stopped.
When you leave the vehicle, any
passengers present can still have
the benefi t of air circulation, even
though the engine is not running.
Engine stopped, ignition switched
on:
- The displays will light up, with the air blower shown empty as
long as the function is available.
- A press on the REST button acti- vates the function for a timing of
just a few minutes. Two blades of
the blower will fi ll to signify that
the function is active.
- It can be deactivated and reacti- vated during the timing.
- At the end of the timing, the dis- play will go off. This button does not activate the air
conditioning, only the air blowers. In
the REST function, the air fl ow and
distribution are controlled automati-
cally and you cannot modify them.

On stopping the engine:
- The displays remain lit up, the blower is shown empty and the
function can be activated for
30 seconds.
- A press on the REST button during the next 30 seconds ac-
tivates the function for a timing
of several minutes. The dura-
tion and availability of the func-
tion are variable according to the
state of charge of the battery (a
protection to guarantee engine
starting). Two blower blades fi ll
up to signify that the function is
active. It remains active, even af-
ter the doors have been locked,
until the end of the timing.
- A further press before the end of the timing defi nitively stops the
function. 4. Adjustment of the air
distribution

 Press on button 4 so that
the air fl ows scroll suc-
cessively on the display.
The air distribution you have chosen
is confi rmed by the lighting of the
corresponding warning lamps in the
display.
There are 7 possible adjustments.
5. Air recirculation
This button activates the recircula-
tion of air within the passenger com-
partment and also has an automatic
function.
Entry of air in automatic
mode (activated by default, in
automatic comfort regulation)
According to version, the automatic
mode makes use of an air quality
sensor. This analyses the air and
isolates the passenger compart-
ment from the exterior as soon as it
detects the presence of pollutants.
Then it automatically activates recir-
culation of cabin air.

51
III
C O M F O R T

Closing of the air inlet

 Press on button 5 to
close off the entry of air
from outside.

Entry of air (manual mode)

 Press on button 5 to activate en-
try of air from the outside. The
warning lamp goes out.

 Press once on button 5 to return
to the initial status (entry of air in
automatic mode).
The air recirculation can also be ac-
cessed by means of a press on the
control, located low down to one side
of the steering wheel (see "§ Fixed
centred controls steering wheel"). 6. Adjustment mode for the
rear passengers
This button decides whether
or not the rear passengers
may use their adjustment
controls.
There are three possible statuses
for this button:

Locking of the rear
passenger controls

Authorisation of the rear
passenger controls

Reduction of the
air fl ow for the rear
passengers
With additional air conditioning, in
cold weather you are advised to
close the supply of air to the rear
passengers (no hot air distribution
possible via these air vents).
The rear passengers can use
their adjustment controls at their
convenience.
The driver imposes his adjustment
on the rear passengers. In this case,
the rear passenger controls are
deactivated. 7. Panel display mode: black
panel function
This function turns the dis-
plays and panel backlighting
on or off.
- Function activated, a press on any button will light up the screen
temporarily.
- press on button 7 deactivates
the function, lighting of buttons
and screen is again permanent.
This function optimises notably the
visual comfort for driving at night.
8. Demisting/defrosting of the rear screen
This can only operate when the en-
gine is running.

 Press on button 8 to activate/
deactivate the electric demist-
ing/defrosting of the rear screen
and, according to version, of the
exterior rear view mirrors. The
warning lamp lights up and the
symbol appears on the display.
It switches off automatically
to prevent excessive con-
sumption of power.
Whilst retaining the other adjust-
ments, this position enables the
driver at any time to exclude any dis-
agreeable odours or fumes coming
from outside the vehicle. It should
be cancelled as soon as possible to
permit renewal of cabin air and to
prevent misting.

52
C O M F O R T
9. Rapid demisting/defrosting of the front and rear
windows
- Press on button 9 . The warning
lamp lights up.
This function gives a rapid
demisting/defrosting of the
vehicle simultaneously with:
- front demisting/defrosting at op- timum temperature,
- optimum air fl ow,
- recirculation prohibition,
- demisting/defrosting of the rear view mirrors and heated rear
screen,
- air conditioning, if necessary.
Press again on button 9 or on AUTO
to stop the function. Demisting/
defrosting of the rear view mirrors
and heated rear screen remains
activated.
10. Air conditioning

 Press on button 10 to activate
the air conditioning.
The A/C warning lamp lights up.
PANELS
11. Front passenger
The front passenger can adjust their
temperature control independently at
any time by pressing buttons + and - .
The front passenger con-
trols the adjustment of their
own temperature.
The temperature for the
passenger is aligned with
that for the driver. 12. Rear passengers
(right/left)
By default, in AUTO
position, the adjust-
ment of the air fl ow is
aligned on the front
ventilation.

 Rotate the button
to decrease or in-
crease the air fl ow.
You can adjust the air fl ow only if
the driver enables you to (see but-
ton 6 of the driver’s control panel).

51
III
C O M F O R T

Closing of the air inlet

 Press on button 5 to
close off the entry of air
from outside.

Entry of air (manual mode)

 Press on button 5 to activate en-
try of air from the outside. The
warning lamp goes out.

 Press once on button 5 to return
to the initial status (entry of air in
automatic mode).
The air recirculation can also be ac-
cessed by means of a press on the
control, located low down to one side
of the steering wheel (see "§ Fixed
centred controls steering wheel"). 6. Adjustment mode for the
rear passengers
This button decides whether
or not the rear passengers
may use their adjustment
controls.
There are three possible statuses
for this button:

Locking of the rear
passenger controls

Authorisation of the rear
passenger controls

Reduction of the
air fl ow for the rear
passengers
With additional air conditioning, in
cold weather you are advised to
close the supply of air to the rear
passengers (no hot air distribution
possible via these air vents).
The rear passengers can use
their adjustment controls at their
convenience.
The driver imposes his adjustment
on the rear passengers. In this case,
the rear passenger controls are
deactivated. 7. Panel display mode: black
panel function
This function turns the dis-
plays and panel backlighting
on or off.
- Function activated, a press on any button will light up the screen
temporarily.
- press on button 7 deactivates
the function, lighting of buttons
and screen is again permanent.
This function optimises notably the
visual comfort for driving at night.
8. Demisting/defrosting of the rear screen
This can only operate when the en-
gine is running.

 Press on button 8 to activate/
deactivate the electric demist-
ing/defrosting of the rear screen
and, according to version, of the
exterior rear view mirrors. The
warning lamp lights up and the
symbol appears on the display.
It switches off automatically
to prevent excessive con-
sumption of power.
Whilst retaining the other adjust-
ments, this position enables the
driver at any time to exclude any dis-
agreeable odours or fumes coming
from outside the vehicle. It should
be cancelled as soon as possible to
permit renewal of cabin air and to
prevent misting.

52
C O M F O R T
9. Rapid demisting/defrosting of the front and rear
windows
- Press on button 9 . The warning
lamp lights up.
This function gives a rapid
demisting/defrosting of the
vehicle simultaneously with:
- front demisting/defrosting at op- timum temperature,
- optimum air fl ow,
- recirculation prohibition,
- demisting/defrosting of the rear view mirrors and heated rear
screen,
- air conditioning, if necessary.
Press again on button 9 or on AUTO
to stop the function. Demisting/
defrosting of the rear view mirrors
and heated rear screen remains
activated.
10. Air conditioning

 Press on button 10 to activate
the air conditioning.
The A/C warning lamp lights up.
PANELS
11. Front passenger
The front passenger can adjust their
temperature control independently at
any time by pressing buttons + and - .
The front passenger con-
trols the adjustment of their
own temperature.
The temperature for the
passenger is aligned with
that for the driver. 12. Rear passengers
(right/left)
By default, in AUTO
position, the adjust-
ment of the air fl ow is
aligned on the front
ventilation.

 Rotate the button
to decrease or in-
crease the air fl ow.
You can adjust the air fl ow only if
the driver enables you to (see but-
ton 6 of the driver’s control panel).

53
III
C O M F O R T
ADDITIONAL AIR CONDITIONING
Additional air conditioning allows you
to optimise comfort levels in warm
weather conditions. It produces ad-
ditional fresh air which is supplied
using the rear air vents. The supply
of warm air via the rear air vents is
not possible using this system.
C. REAR PASSENGER CONTROL PANELS (RIGHT/LEFT)
13. Adjustment of temperature
The rear passengers can adjust their
temperature controls independently
via buttons + and - .
Their preference cannot be great-
er than that of the driver by more
than 2. The reaching of this maxi-
mum preference is confi rmed by the
fl ashing of its display.
14. Adjustment of air blower speed
The air blower operates only when
the engine is running.
To adjust the fl ow of air, press on
button:
to increase the air fl ow,
to decrease the air fl ow. The level of air fl ow is indicated on
the display by the progressive fi lling
of the ventilator blades.
By reducing the fl ow to minimum,
you deactivate the air conditioning
system (OFF).
You can adjust the temperature and
the air fl ow only if the driver enables
you to (see button
6 of the driver’s
control panel).
This warning lamp signifi es
that the passenger controls
are locked, you can adjust
neither the temperature nor
the air fl ow, which remain aligned on
the preferences of the driver.
This warning lamp indi-
cates that the supply of air
is cut off .
This position is recommended in
cold weather conditions, as the air
vents do not supply warm air.