display Citroen C4 PICASSO DAG 2010.5 1.G Service Manual

IX
156
D R I V I N G
Manual operation
Position of the selector lever for
manual gear changing.
 Move the selector lever
to position M .
 Pull the " + " paddle to change up
a gear.

 Pull the " - " paddle to change
down a gear.
- If the vehicle stops or reduces speed (for example when ap-
proaching a stop sign), the gear-
box changes down automatically
to fi rst gear.
- In sequential mode, it is not nec- essary to release the accelerator
during gear changes.
- A request to change gear is ac- cepted only if the engine speed
permits it. - For safety reasons, depending
on the engine speed, a change
up or down may be performed
automatically.
- It is possible at any time to move from position D (driving in auto-
matic mode) to position M (driv-
ing in sequential mode) or vice
versa.
Flashing of the indicator for
the position requested sig-
nals that this position is not
yet obtained.
If the indicator is on fi xed, the posi-
tion is confi rmed.
Display of a dash in the rev counter
indicates a malfunction. Consult a
CITROËN dealer.
Lighting of the service warning
lamp accompanied by a message
and an audible signal indicates an
operating fault. In this case:
- a marked snatching may be felt when selecting R for reverse
gear,
- the gearbox is locked in one gear,
-
do not exceed a speed of 60 mph
(approximately 100 km/h).
Consult a CITROËN dealer.

IX
158
D R I V I N G
Optional function controls

1. Call/Hang up the telephone (see
"Audio and Telematics" section).

2. Rheostat for dashboard lighting.

3. Start of voice recognition (see
"Audio and Telematics" section).

4. Personalisation button:
- courtesy lamp on/off or
- diagnostics
Press this button for more than two seconds to display the per-
sonalisation menu.

5. Air recirculation. Multifunction screen controls

A. Selection of the type of informa-
tion to be displayed on the right
of the screen (radio, trip comput-
er, navigation/guidance…).
For the multifunction screen A, choice of activation/deactivation
of functions and setting choices.

B. Access to the "Main Menu" * .

C. Confi rmation of the function cho-
sen or of the value modifi ed.
Call/Hang up (see "Audio and Telematics" section).

D. Scrolling in the multifunction
screen.

E. Cancellation of the current ope-
ration or return to the previous
display.
* To comply with legislation in certain countries, the "Menu" control may
be deactivated while the vehicle is
in motion.

IX
159
D R I V I N G
SPEED LIMITER
System which prevents the vehi-
cle from exceeding the speed pro-
grammed by the driver.
Once the limit speed has been
reached, the accelerator pedal no
longer has any effect.
The speed limiter is switched on
manually: a speed of at least 20 mph
(approximately 30 km/h) must be pro-
grammed.
The speed limiter controls are located
on the left-hand side of the steering
wheel. The programmed information is
grouped together in zone
A of the
instrument panel screen.
Steering mounted controls Displays on the instrument
panel
Programming
Rotate the control
1 to the "LIM" po-
sition. With the engine running, you can
adjust the memorised maximum
speed, by means of short or long
presses on:

 button 4 to increase the memo-
rised maximum speed,

 button 2 to decrease the memo-
rised maximum speed.
Successive presses will modify the
maximum speed in steps of 1 mph
(1 km/h) and a sustained press in
steps of 3 mph (5 km/h).
Activation
When the desired maximum speed
is displayed, press button 3 so that
the limitation is activated.
On selection of the
function, the previous
memorised speed and
the information "OFF"
are displayed on the
instrument panel. The information
"OFF"
then disappears from
the instrument panel
screen.
While the function is active, press-
ing the accelerator pedal will not en-
able the programmed speed to be
exceeded, except if you press the
pedal hard down to beyond the end-
of-travel switch.
The speed of your vehicle may vary
slightly in relation to that memo-
rised.
The speed limiter cannot, in any circum-
stances, take the place of the obser-
vance of speed limits or of the vigilance
and responsibility of the driver.

IX
160
D R I V I N G
Deactivation
Press on button 3 .
This action causes the
information "OFF" to
appear on the instru-
ment panel screen.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A of the
instrument panel.
Override of the programmed
speed
The accelerator pedal is equipped
with an end-of-travel switch. If you
action this switch by pressing the
pedal hard down, you can exceed
the memorised maximum speed at
any time.
During the time the speed is be-
ing exceeded, the displayed speed
fl ashes.
You have only to release the ac-
celerator pedal to return below the
maximum speed and render the
function active again. Return to normal driving

 By moving the control 1 from po-
sition "LIM" to position 0 .

 By the engine stopping.
The speed previously chosen is still
memorised. Operating fault
If there is a speed limiter malfunc-
tion, a message will display accom-
panied by an audible signal and
lighting of the service warning lamp.
Have it checked by a CITROËN
dealer.
If during the operation of the speed
limiter, the system is unable to keep
within the maximum speed (for exam-
ple on a steep descent or under heavy
acceleration) then the speed fl ashes.
Adapt your speed as necessary.
The function will re-engage when
your speed returns below the de-
sired maximum speed.
On a steep downhill gradi-
ent or on sharp accelera-
tion, the speed limiter will
not be able to prevent the vehicle
from exceeding the programmed
speed.
Use of fl oor mats that are not ap-
proved by CITROËN may hinder
access to the accelerator pedal
and thus interfere with the function-
ing of the speed limiter.
To avoid any risk of interfering with
the pedals:
- check that the fl oor mat is cor- rectly positioned,
- never use more than one fl oor mat.

IX
161
D R I V I N G
CRUISE CONTROL
System which automatically main-
tains the vehicle speed programmed
by the driver, without any action on
the accelerator pedal.
The cruise control is switched on
manually: the vehicle speed must
be at least 25 mph (approximately
40 km/h) and you must engage:
- fourth gear on a manual gear-box,
- second gear, in sequential mode, on an electronic gearbox or au-
tomatic gearbox,
- position A on an electronic gear-
box or D on an automatic gearbox.
Steering mounted controls
The cruise control switches are lo-
cated on the left-hand side of the
steering wheel. The programmed information is
grouped together in zone
A of the
instrument panel screen.
Displays on the instrument
panel
Activation You can then release the accelerator
pedal. The vehicle will automatically
keep to the speed chosen.
The speed of your vehicle may vary
slightly in relation to that memo-
rised.
You can adjust the memorised speed
on the instrument panel screen by
pressing on:

 button 4 to increase the speed,

 button 2 to decrease the speed.
Successive presses modify the cruise
speed in steps of 1 mph (1 km/h) and
a sustained press in steps of 3 mph
(5 km/h).
Deactivation

 Either by pressing on the brake
pedal or on the clutch pedal.

 Or by pressing button 3 .

 Or if either the ESP or the ASR
system is active.
The cruise control is not active if the
gear lever is in neutral.
On selection of the
function via control
1,
no cruise speed has
yet been memorised .
Programming
Rotate the control
1 to the "REG"
position.
Once the desired speed has been
reached using the accelerator, press
button 2 or button 4 . The cruise
speed is then memorised. It is dis-
played in zone A of the instrument
panel. These actions cause
the information
"OFF"
to appear on the instru-
ment panel screen.
These actions do not
cancel the cruise speed
which remains displayed
in the instrument panel.
The cruise control cannot, in any circum-
stances, take the place of the obser-
vance of speed limits or of the vigilance
and responsibility of the driver.

IX
162
D R I V I N G
Reactivation

 By recall of the memorised
speed
After a disengagement, press on button 3 . Your vehicle automati-
cally returns to the memorised
cruise speed which is displayed
in zone A .
If the memorised cruise speed is higher than the current speed,
the vehicle will accelerate to
reach the former.

 By selection of the current
speed
Press on button 2 or 4 once the
desired speed has been reached.
The information "OFF" will then
disappear from the instrument
panel display.
Overriding the programmed
speed
During the operation of cruise con-
trol, it is always possible to use the
accelerator to go faster than the
cruise speed (for example to over-
take another vehicle). The speed
displayed in zone A fl ashes.
You have only to release the accel-
erator pedal to return to the cruise
speed. If during the operation of cruise
control, the system is unable to
keep within the memorised speed
(for example on a steep descent),
then the speed fl ashes. Adapt your
speed as necessary.
Return to normal driving Operating fault

If there is a malfunction, a mes-
sage will display accompanied by
an audible signal and lighting of the
service warning lamp.
Have it checked by a CITROËN
dealer.
Cruise control should only
be used when the driving
conditions allow you to drive
at a constant speed.
Do not use it in heavy traffi c, or on
dangerous or slippery roads.
The driver must remain attentive
and in full control of his vehicle.
You are recommended to keep your
feet within range of the pedals.
To avoid any risk of interfering with
the pedals:
- check that the fl oor mat is cor- rectly positioned,
- never use more than one fl oor mat.

 By an action on the control 1 from
position "REG" to position 0 .

 By the engine stopping.
The cruise speed previously chosen is no longer memorised.

IX
163
D R I V I N G
PARKING SPACE SENSORS
After measuring the parking space
available between two vehicles or
obstacles, this system gives you in-
formation on:
- the possibility of fi tting into a free space, depending on the dimen-
sions of your vehicle and the dis-
tances needed for manoeuvring,
- the level of diffi culty of the ma- noeuvre to be performed.
The system does not measure spac-
es which are clearly much smaller or
larger than the size of the vehicle. Displays on the instrument
panel
The parking space sensor
function warning lamp can
have three different states:
- off: the function is not selected,
- on fi xed: the function is selected
but the conditions for measure-
ment are not yet met (direction
indicator not operating, speed
too high) or the measurement
phase has ended.
- fl ashing: measurement is in
progress or the message is being
displayed. You can activate the "parking space
sensor" function by pressing but-
ton
A . The fi xed illumination of the
warning lamp indicates that the
function is selected.

IX
164
D R I V I N G
Operation
You have identifi ed a parking
space:

 Press button A to activate the
function.

 Activate the direction indicator
on the side where the space is to
be measured.

 During the measuring, go for-
ward the length of the space, at
a speed less than 12 mph (ap-
proximately 20 km/h), to prepare
for your manoeuvre.
The system then measures the size of the space.

 The system informs you of the
level of diffi culty of the manoeu-
vre via a message on the multi-
function screen accompanied by
an audible signal.
Parking possible

Parking diffi cult

Parking not advised
The function displays the following
types of message: The function deactivates itself auto-
matically:
- when you engage reverse gear,
- when you switch off the ignition,
- fi ve minutes after activation of
the function or after the last mea-
surement operation,
- if the vehicle speed exceeds the threshold of 45 mph (approxi-
mately 70 km/h) for one minute.
If there is a malfunction,
have the system checked
by a CITROËN dealer.
If the lateral distance between your
vehicle and the parking space is too
great, the system may not operate.
- The function remains available
after each measurement and so
can measure a number of places
successively.
- In bad weather or in winter, en- sure that the sensors are not cov-
ered by dirt, or by ice or snow.
- The parking space sensor func- tion deactivates the front parking
sensors during the space mea-
suring phase when you are in
forward gear.

IX
166
D R I V I N G
PARKING SENSORS
This system indicates the proximity
of an obstacle (person, vehicle, tree,
gate, etc.) which comes within the
fi eld of detection of sensors located
in the bumper.
Certain types of obstacle (stake,
roadworks cone, etc.) detected ini-
tially will no longer be detected at
the end of the manoeuvre due to the
presence of blind spots. Visual assistance
This supplements the audible sig-
nal by displaying segments on the
multifunction screen which move
progressively nearer to the vehicle.
When the obstacle is near, the sym-
bol "Danger" is also displayed on the
screen.
Audible assistance
The proximity information is given by
a discontinuous audible signal, the
frequency of which increases as the
vehicle approaches the obstacle.
The sound emitted by the speaker
(right or left) indicates the side on
which the obstacle is located.
When the distance between the
vehicle and the obstacle becomes
less than approximately thirty centi-
metres, the audible signal becomes
continuous.
This function cannot, in any circum-
stances, take the place of the vigi-
lance and responsibility of the driver.
Rear parking sensors
The system is switched on by en-
gaging reverse gear. This is accom-
panied by an audible signal.
The system is switched off when you
exit reverse gear.

IX
167
D R I V I N G
Front parking sensors
In addition to the rear parking sen-
sors, the front parking sensors are
triggered when an obstacle is de-
tected in front and the speed of the
vehicle is still below 6 mph (10 km/h).
The sound emitted by the speaker
(front or rear) indicates whether the
obstacle is in front or behind.
The front parking sensors are inter-
rupted if the vehicle stops for more
than three seconds in forward gear,
if no further obstacles are detected
or when the speed of the vehicle ex-
ceeds 6 mph (10 km/h). Deactivation/Activation of the
front and rear parking sensors
The function is deactivated by press-
ing this button. The indicator lamp
on the button comes on.
Pressing this button again reacti-
vates the function. The indicator
lamp on the button switches off.
The function will be deactivated au-
tomatically if a trailer is being towed
or a bicycle carrier is fi tted (vehicle
fi tted with a towbar or bicycle car-
rier recommended by CITROËN). Operating fault
If an operating fault occurs,
when reverse gear is en-
gaged this warning lamp is
displayed on the instrument
panel and/or a message appears on
the screen, accompanied by an au-
dible signal (short bleep).
Consult a CITROËN dealer.
In bad weather or in winter, ensure
that the sensors are not covered
with mud, ice or snow. When re-
verse gear is engaged, an audible
signal (long bleep) indicates that
the sensors may be dirty.
When the vehicle is moving at a
speed below 6 mph (10 km/h), cer-
tain sound sources (motorcycle, lor-
ry, pneumatic drill, etc.) may trigger
the audible signals of the parking
sensor system.