boot Citroen C4 PICASSO RHD 2015 1.G Owner's Guide

263
*  Depending  on   version.   The   complete   tooling  i
s   with   the   spare   wheel.
Changing a wheelProcedure for changing a wheel with a punctured tyre by the spare wheel using the tools provided with the vehicle.
S
ome
 
of
 
the
 
tools   are   accessible   from   inside  
t

he
 
boot.
 
The
 
wheel   chocks   2 as well as the
wheelbrace
 
extension   6   are   stowed   under   the  
r

ight
 
hand
 
boot   sill.
The wheelbrace 1
  and   the   towing   eye   7 are
stowed
 
under
 
the   left   hand   boot   sill.
The
 
other
 
tools,   the   jack   3   and   the   tool   for  
r

emoving
 
the
 
wheel   bolt   head   finishers   for   alloy  
w

heels 4 ,
 
are
 
stowed   in   a   box   attached   to   the  
s

pare
 
wheel.
 
The   assembly   is   secured   under  
t

he
 
vehicle
 
in
 
a   carrier.   See   the   "Access   to   the  
s

pare
 
wheel"
 
section).
Access to the vehicle's tools*
2. Wheel   chocks   for   immobilising   the   vehicle  (
except   versions   with   manual   gearbox).
3.
 J

ack   with   integral   handle.
 F

or   raising   the   vehicle.
4.
 W

heel   bolt   head   cover   removal   tool.
 F

or   removing   the   wheel   bolt   head   finishers  
o

n   alloy   wheels.
5.
 S

ocket   for   the   security   bolts   (stowed   in   the  
g

love   box).
 F

or   adapting   the   wheelbrace   to   the   special  
s

ecurity   bolts.
6.
 W

heelbrace
 e
xtension.
 F

or   unscrewing/tightening   the   spare   wheel  
c

arrier   drive.
7.
 T

owing   eye.
Wheel with trim
When removing the wheel ,   detach   the   trim  f
irst   using   the   wheelbrace   1   pulling   at   the   valve  
p

assage   hole.
When refitting the wheel ,
  refit   the   trim  
s

tarting   by   placing   its   notch   facing   the   valve  
a

nd   press   around   its   edge   with   the   palm   of  
y

our hand.
List of tools*
all of these tools are specific to your vehicle
and   can   vary   according   to   equipment.   Do   not  
u

se   them   for   other   purposes.
1.
 W

heelbrace.
 F

or   removing   the   wheel   trim   and   the   wheel  
f

ixing
 bol
ts.
7
Practical information

265
A puncture wheel from the vehicle cannot   be   fitted   under   the   vehicle.   It  
m

ust  
b
e  
c
arried  
i
n  
t
he  
b
oot.  
U
se  
a
 
c
over  
t

o   protect   the   boot.
F
 
P

ress
 
the
 
tongue,
 
slide
 
the
 
box
 
cover
 
to
 
the
 
c

entre
 
a

nd
 
r

emove
 
i

t
 
f

or
 
a

ccess
 
t

o
 
t

he
 
o

ther
 
t

ools
 
( jack
 
and
 
wheel
 
bolt
 
head
 
finisher
 
r

emoval
 
tool
 
for
 
alloy
 
wheels).Putting the spare wheel back in
place
F Stow   the   corresponding   tools   in   the   box  a
nd   close   the   cover.
F
 
P
osition   the   tool   box   on   the   ground.
Stowing the tools
F Return  the   tools   to   the   box   and   stow   the  b
ox   in   the   vehicle's   boot.
F
 
W
ind   in   the   carrier   by   turning   the  
w

heelbrace   clockwise:   once   the   cable   is  
f

ully   wound   in   you   should   no   longer   feel  
an

y
 r
esistance.
F

S
tow the other tools in the locations
provided
  in   the   boot.
7
Practical information

269
F Remove  the   bolts   and   store   them   in   a   clean  p
lace.
F
 
R
emove   the   wheel.
Ensure
  that   the   jack   is   stable.   If   the  
g

round   is   slippery   or   loose,   the   jack  
m

ay   slip   or   drop   -   Risk   of   injury!
Ensure
  that   the   jack   is   positioned   only  
a

t   one   of   the   jacking   points   A or B
under
  the   vehicle,   making   sure   that   the  
v

ehicle's   contact   sur face   is   centred   on  
t

he   head   of   the   jack.   Other wise   there   is  
a

  risk   of   damage   to   the   vehicle   and/or   of  
t

he   jack   dropping   -   Risk   of   injury!
Fitting a wheel
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels, when   tightening   the   bolts   on   fitting,   it  
i

s   normal   to   notice   that   the   washers  
d

o   not   come   into   contact   with   the  
"

space-saver"   spare   wheel.   The   wheel  
i

s   secured   by   the   conical   sur face   of  
e

ach   bolt.
After changing a wheel
To correctly store the punctured wheel in the boot ( not in the location of the
space-saver wheel ),
  first   remove   the  
c

entral   cover.
When
  using   the   "space-saver"   type  
s

pare   wheel,   do   not   exceed   50   mph  
(

80 km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop   without   delay.
Have
  the   punctured   wheel   repaired  
a

nd   refitted   to   the   vehicle   as   soon   as  
p

ossible.
7
Practical information

277
Lamps on the tailgate
Model with LED lamps
Identify
 
the
 
failed
 
bulb.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
access
 
cover.
Model with conventional bulb lamps
F
 
R

emove
 
the
 
three
 
lamp
 
fixing
 
screws
 
A .
F
 
D

isconnect
 
the
 
lamp
 
connector.
F
 
C

arefully
 
remove
 
the
 
lamp
 
from
 
the
 
outside
 
b

y
 
pressing
 
the
 
retaining
 
clip
 
B .
F
 
T
urn   the   bulb   holder   a   quarter   of   a   turn  
a

nti-clockwise   and   pull   the   bulb   out.
F
 
C
hange   the   bulb.
For
  reassembly,   carry   out   these   operations   in  
r

everse
 o
rder.
7
Practical information

279
Lamps on the tailgateModel with LED lamps
Model with conventional bulb lamps
Identify
 
the
 
failed
 
bulb.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
access
 
cover. F
 
R

emove
 
the
 
three
 
lamp
 
fixing
 
screws
 
A .
F
 
D

isconnect
 
the
 
lamp
 
connector.
F
 
C

arefully
 
r

emove
 
t

he
 
l

amp
 
f

rom
 
i

ts
 
h

ousing.
F
 
T

urn
 
the
 
bulb
 
holder
 
a
 
quarter
 
of
 
a
 
turn
 
a

nti-clockwise
 
and
 
pull
 
the
 
bulb
 
out.
F
 
C

hange
 
the
 
bulb.
For
 
reassembly,
 
carry
 
out
 
these
 
operations
 
in
 
r

everse
 o

rder.
7
Practical information

283
Type 1 fuse tables
Fusebox 1
Dashboard fuses
The fusebox is located in the lower dashboard (left-hand   side).
Access to the fuses
F Refer  to   the   paragraph   "Access   to   the   tools".Fuse N°
Rating Functions
F8 5 ASteering   mounted   controls
F18 20 ATouch   screen   tablet,   audio   and   navigation   system,   CD   player,  
U

SB   ports   and   auxiliary   sockets.
F16 15 AFront   12V   socket.
F15 15 ABoot   12V   socket.
F28 5 ASTART/STOP   button.
F30 15 ARear   wiper.
F27 15 AFront   screenwash   pump,   rear   screenwash   pump.
F26 15 AHorn.
F20 5 AAirbags.
F21 5 AInstrument   panel.
F19 5 ARain   and   sunshine   sensor.
F12 5 AKeyless   starting   unit.
F2 5 AManual
 h
eadlamp
 a
djustment
 c
ontrol.
7
Practical information

285
Type 2 fuse tables
Fuse N°Rating Functions
F3 3 ASTART/STOP
  button.
F6 A 15 ATouch
  screen   tablet,   audio   and   navigation   system,   CD   player,  
U

SB   ports   and   auxiliary   sockets.
F8 5 AAlarm.
F9 3 ASteering
  mounted   controls.
F19 5 AInstrument
  panel.
F24 3 ARain
  and   sunshine   sensor.
F25 5 AAirbags.
F33 3 AMemorisation
 o

f
 d
riving
 p
osition.
F34 5 AElectric
  power   steering.
F13 10 AFront
  12V   socket.
F14 10 ABoot
  12V   socket.
F16 3 AMap
  reading   lamps   in   row   1   courtesy   lamps.
F27 5 AElectronic
  gearbox   gear   selector.
F30 20 ARear
  wiper.
F38 3 AManual
 h

eadlamp
 a
djustment
 c
ontrol.
7
Practical information

293
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F
 
l
ift   the   floor   and   remove   it,
F
 
r
emove   the   towing   eye   from   its   housing.
General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
 
f
our-wheel   drive   vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another   vehicle   using   the   towing   eye.
Access to the tools
7
Practical information

302
accessories
A wide range of accessories and genuine parts is available from the CITROËN dealer network.
T hese   accessories   and   parts   are   all   suitable   for   your   vehicle   and   benefit   from   CITROËN's   recommendation   and   warranty.
"Comfort"
Door deflectors, side window blinds, rear screen   blind,   insulated   module,   coat   hanger  
f

ixed   to   head   restraint,   mobile   reading  
l

amp,   mirror   for   caravan,   parking   sensors,  
p

rogrammable   additional   heating,   smoker's  
k

it,   solar   film   for   rear   door   windows,   portable  
s

cented   air   freshener...
"Transport systems"
boot carpet, boot liner, boot net, boot spacers,
transverse  roof   bars,   ski   carrier,   roof   boxes,  
t

owbars,   towbar   wiring   harnesses,   bicycle  
c

arriers   for   towbar   and   roof   bars,   towbars  
w

ith   fixed   and   detachable   towball,   separation  
n

et,   sliding   carrier,   boot   organiser   (Grand   C4  
P

icasso)...
If
  a   towbar   and   wiring   harness   are   fitted  
o

utside   the   CITROËN   dealer   network,   the  
i

nstallation   must   be   done   strictly   in   line   with   the  
ma

nufacturer's
 r
ecommendations.
If
  your   vehicle   has   a   detachable   towball,   it   is  
r

ecommended   that   the   ball   be   removed   when  
n

ot   towing.
"Styling"
Gear lever knobs, aluminium foot rest, alloy wheels...
"Security and safety"
Anti-intrusion alarm, stolen vehicle tracking system,   child   seats   and   booster   cushions,  
b

reathalyser,   first   aid   kit,   fire   extinguisher,  
w

arning   triangle,   high   visibility   vest,   wheel  
s

ecurity   bolts,   snow   chains,   non-slip   covers,  
w

inter   tyres,   foglamp   kit,   security   film   for   front  
d

oor   windows,   dog   guard,   pet   seat   belt...
"Protection"
Mats*, seat covers compatible with lateral airbags,   mud   flaps,   door   protective   mouldings,  
b

umper   protection   strips,   vehicle   cover,   boot  
s

ill   protector,   door   sill   protectors,   seat   and   boot  
p

rotective   covers   for   pets...
The
  rear   bodywork   has   been   designed   to   avoid  
s

p r ay.
*
 
T
o   avoid   any   risk   of   jamming   the   pedals:
-
 
e
nsure   that   mats   are   correctly   positioned  
a

nd   secured,
-
 
n
ever   fit   one   mat   on   top   of   another.
Practical information

319
AdBlue® additive and SCR system
f
or
 
BlueHDi   Diesel   engines
To assure respect for the environment and c
onformity   with   the   new   Euro   6   emissions  
s

tandard,   without   adversely   affecting   the  
p

er formance   or   fuel   consumption   of   Diesel  
e

ngines,   CITROËN   has   taken   the   decision   to  
e

quip   its   vehicles   with   an   effective   system   that  
a

ssociates   SCR   (Selective   Catalytic   Reduction)  
w

ith   a   particle   filter   (FAP)   for   the   treatment   of  
e

xhaust   gases.
Presentation of the SCR system
Using an additive called AdBlue® containing u
rea,
 
a
 
catalytic
 
converter
 
turns
 
up   to   85%  
o

f
 
nitrous
 
oxides
 
(NOx)
 
into
 
nitrogen   and  
w

ater,
 
which
 
are
 
harmless
 
to
 
health   and   the  
e

nvironment. The
  AdBlue
® additive is held in a special t
ank
 
located
  under   the   boot   at   the   rear   of  
t

he
 
vehicle.
 
It   has   a   capacity   of   17   litres:   this  
p

rovides
 
a
 
driving   range   of   about   12   500   miles  
(

20
 
000
 
km),
  after   which   an   alert   is   triggered  
w

arning
 
you
 
when   the   reserve   remaining   is  
e

nough
 
for
 
just   1   500   miles   (2   400   km).
During
 
each
  scheduled   service   of   your   vehicle  
b

y
 
a
 
CITROËN   dealer   or   a   qualified   workshop,  
t

he
 
AdBlue
® additive tank is refilled in order to a
llow
 
normal   operation   of   the   SCR   system.
If
 
the
 
estimated   mileage   between   two   services  
i

s
 
greater
 
than   12   500   miles   (20   000   km),   we  
r

ecommend
  that   you   go   to   a   CITROËN   dealer  
o

r
 
a
 
qualified   workshop   to   have   the   necessary  
t

op-up
 
carried   out. Once
  the   AdBlue
® tank is empty, a s
ystem
 
required
  by   regulations  
p

revents
 
starting
 
of   the   engine.
If the SCR

is faulty, the level of
emissions
 
from
 
your   vehicle   will   no  
l

onger
 
meet
 
the
 
Euro   6   standard:   you  
v

ehicle
 
becomes
 
polluting.
In
 
the
 
event
 
of
 
a
 
confirmed   fault  
w

ith
 
the
 
SCR
 
system,   you   must   go  
t

o
 
a
 
CITROËN
 
dealer   or   a   qualified  
w

orkshop
 
as
 
soon   as   possible:   after  
a

 
running
 
distance   of   650   miles  
(

1 100
 
km),
 
a
 
system   will   be   triggered  
a

utomatically
 
to
 
prevent   engine   starting.
8
Checks