engine Citroen C4 RHD 2011 2.G Owner's Guide

3
COMFORT
75
MIRRORS

Door mirrors

Each fi tted with an adjustable mirror
glass permitting the lateral rearward
vision necessary for overtaking or
parking. They can also be folded for
parking in confi ned spaces.

Demisting - Defrosting

)
Move control A
to the right or to
the left to select the corresponding
mirror.

)
Move control B
in all four directions
to adjust.

)
Return control A
to the central
position.
Adjustment
If the mirrors are folded using
control A
, they will not unfold
when the vehicle is unlocked.
Pull again on control A
.

The objects observed are, in reali ty,
closer than they appear.
Take this into account in order to
correctly judge the distance of ve-
hicles approaching from behind.


Folding


)
From outside: lock the vehicle using
the remote control or the key.

)
From inside: with the ignition on,
pull control A
rearwards.
The folding and unfolding of the
door mirrors using the remote
control can be deactivated by a
CITROËN dealer.
Unfolding


)
From outside: unlock the vehicle us-
ing the remote control or the key.

)
From inside: with the ignition on,
pull control A
rearwards.
Never fold or unfold the electric
folding mirrors manually.

If your vehicle is fi tted with heated
mirrors, the demisting-defrosting
operates with the engine run-
ning, by switching on the heated
rear screen (refer to the "Rear
screen demist-defrost" page).

3
76







Automatic tilting in reverse gear
System which provides a view of the
ground during parking manoeuvres in
reverse gear.

Programming


)
With the engine running, engage
reverse gear.

)
Select and adjust the left-hand and
right-hand mirrors in succession.
The adjustment is stored immediately.
Switching on


)
With the engine running, engage re-
verse gear.

)
Move control A
to the right or to
the left to select the corresponding
mirror.
The glass of the mirror selected tilts
downwards, in accordance with its
programming.

Switching off


)

Exit reverse gear and wait ten seconds.

or


)
Return control A
to the central
position.
The mirror glass returns to its initial
position.
The mirror glass also returns to its initial
position:


-
if the speed exceeds 6 mph (10 km/h),

- if the engine is switched off.

4
ACCESS
80


)
Insert the key in the ignition switch.
The system recognises the starting
code.

)
Turn the key fully towards the dash-
board to position 3 (Starting)
.

)
When the engine starts, release the
key.



A heavy object (key fob...), attached to the key and weighing down on
its shaft in the ignition switch, could
cause a malfunction.
Switching the vehicle off



)
Immobilise the vehicle.

)
Turn the key fully towards you to
position 1 (Stop)
.

)
Remove the key from the ignition
switch.








Key left in the "Ignition on"
position
If the key has been left in the ignition
switch, the ignition will be switched off
automatically after one hour.
To switch the ignition back on, turn the
key to position 1 (Stop)
, then back to
position 2 (Ignition

on

)
.
Starting the vehicle
Locating your vehicle

This function allows you to identify your
vehicle from a distance, particularly in
poor light. Your vehicle must be locked.


)
Press the closed padlock
on the remote control.
This will switch on the courtesy lamps
and the direction indicators will fl ash for
a few seconds.
Anti-theft protection


Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code must
be recognised in order for starting to be
possible.
This electronic engine immobiliser locks
the engine management system a few
minutes after the ignition is switched off
and prevents starting of the engine by
anyone who does not have the key.
In the event of a fault, you
are informed by illumina-
tion of this warning lamp,
an audible signal and a message in the
screen.
In this case, your vehicle does not start;
contact a CITROËN dealer as soon as
possible.


)
First press this button to fold the key.



Folding the key

4
ACCESS
82
Lost keys
Visit a CITROËN dealer with the vehicle's V5 registration document and
your personal identifi cation documents.
The CITROËN dealer will be able to retrieve the key code and the tran-
sponder code required to order a replacement key.







Do not throw the remote con-
trol batteries away, they contain
metals which are harmful to the
environment.
Take them to an approved col-
lection point.
Remote control
The high frequency remote control is a sensitive system; do not operate
it while it is in your pocket as there is a possibility that it may unlock the
vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and
out of sight of your vehicle. You run the risk of stopping it from working and
the remote control would have to be reinitialised.
The remote control does not operate when the key is in the ignition, even
when the ignition is switched off, except for reinitialisation.
Locking the vehicle

Driving with the doors locked may make access to the passenger compartment
by the emergency services more diffi cult in an emergency.
As a safety precaution (with children on board), remove the key from the
ignition when you leave the vehicle, even for a short time.
Anti-theft protection

Do not make any modifi cations to the electronic engine immobiliser system;
this could cause malfunctions.
When purchasing a second-hand vehicle

Have the key codes memorised by a CITROËN dealer, to ensure that the
keys in your possession are the only ones which can start the vehicle.

4
ACCESS
87
DOORS

Openin
g



)
After unlocking the vehicle com-
pletely using the remote control or
the key, pull the door handle.


From outside
When the selective unlocking is
activated, the fi rst press of the
remote control unlocking button
permits unlocking of the driver's
door only.

)
Pull the front door control to open
the door; this unlocks the vehicle
completely.

)
Pull the rear door control to open
the door; this unlocks only the door
opened.



From inside
With the selective unlocking ac-
tivated:


- the driver’s door control un-
locks the driver’s door only.

- the passenger’s door control
unlocks the other doors and
the boot.
The interior door controls do
not operate when the vehicle is
deadlocked.
Closing
When a door is not closed correctly:


-
when the engine is running
,
this warning lamp comes on,
accompanied by a message
in the multifunction screen for
a few seconds,

- when the vehicle is moving
(speed
higher than 6 mph (10 km/h)), this
warning lamp comes on, accom-
panied by an audible signal and a
message in the multifunction screen
for a few seconds.

4
ACCESS
88
BOOT

Unlocking the boot



)
Press this button to unlock
the boot.
As a safety measure, this action does
not unlock the doors.


Opening



)
After unlocking the boot or the ve-
hicle using the remote control or the
key, press the opening control, then
raise the tailgate.



Closing



)
Lower the boot lid using the interior
grab handle.


-
when the engine is running
, this warning lamp comes on,
accompanied by a message
in the multifunction screen
for a few seconds,

-
when the vehicle is moving
(speed
above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
in the multifunction screen for a few
seconds.

When the selective unlocking
is activated, the boot can be
opened at the second press
of the unlocking button on the
remote control.
Tailgate release
System for mechanical unlocking of the
boot in the event of a battery or central
locking malfunction.

Unlocking


)
Fold back the rear seats to gain
access to the lock from inside the
boot.

)
Insert a small screwdriver into hole A

of the lock to unlock the tailgate.

If the tailgate is not closed correctly:

4
ACCESS
92
FUEL TANK

Capacity of the tank: approximately
60 litres.

When the low fuel level in the
tank is reached, this warning
lamp on the instrument panel
comes on, accompanied by an
audible warning and a mes-
sage in the screen.
When it fi rst comes on, around
6 litres of fuel remain in the tank.
You must refuel as soon as possible to
avoid running out.


Low fuel level

Refuellin
g

Additions of fuel must be of at least
5 litres to be registered by the fuel gauge.
Opening the fi ller cap may result in an
inrush of air. This vacuum is entirely
normal and results from the sealing of
the fuel system.

If you have put in the wrong
fuel for your vehicle, you must
have have the tank drained and
refi lled with the correct fuel be-
fore you start the engine.

)
Press control A
until the automatic
opening of the fuel fl ap is heard.
This control remains active for a few
minutes after switching off the igni-
tion. If necessary, switch the ignition
on again to reactivate it.

If you are fi lling your tank to the top,
do not persist after the third cut-
off; this could cause your vehicle to
malfunction.

)
Take care to select the pump that
delivers the correct fuel for your
vehicle.

)
Introduce the nozzle so as to push
in the metal non-return fl ap B.

)
Make sure that the nozzle is pushed
in as far as possible before starting
to refuel (risk of blowback).

)
Maintain this position while refuelling.

)
Push the fuel fl ap to close it.






With Stop & Start, never refuel
with the system in STOP mode;
you must switch off the ignition
with the key.

4
ACCESS
93
Quality of the fuel used for petrol engines

The petrol engines are perfectly com-
patible with E10 type petrol biofuels
(containing 10 % ethanol), conforming
to European standards EN 228 and
EN 15376.
E85 type fuels (containing up to 85 %
ethanol) are reserved exclusively for
vehicles marketed for the use of this
type of fuel (BioFlex vehicles). The
quality of the ethanol must comply with
European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing up
to 100 % ethanol (E100 type).

Quality of the fuel used for Diesel engines


The Diesel engines are perfectly com-
patible with biofuels which conform to
current and future European standards
(Diesel fuel which complies with stan-
dard EN 590 mixed with a biofuel which
complies with standard EN 14214)
available at the pumps (containing up
to 7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in certain
Diesel engines; however, this use is sub-
ject to strict application of the special ser-
vicing conditions. Contact a CITROËN
dealer or a qualifi ed workshop.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or dilut-
ed, domestic fuel...) is strictly prohibited
(risk of damage to the engine and fuel
system).


Mechanical device which prevents fi ll-
ing the tank of a Diesel vehicle with
petrol. It avoids the risk of engine dam-
age that can result from fi lling with the
wrong fuel.
Located in the fi ller neck, the misfuel
prevention device appears when the
fi ller cap is removed.
Operation

When a petrol fi ller nozzle is introduced
into the fuel fi ller neck of your Diesel
vehicle, it comes into contact with the
fl ap. The system remains closed and
prevents fi lling.


Do not persist but introduce a Diesel
type fi ller nozzle.



It is still possible to use a fuel
can to fi ll the reservoir.
In order to ensure a good fl ow of
fuel, do not place the nozzle of
the fuel can in direct contact with
the fl ap of the misfuel prevention
device.

This equipment will become available
during the year. The petrol or Diesel engine of your ve-
hicle is fi tted with a catalytic converter,
a device which helps to reduce the level
of harmful emissions in the exhaust
gases.

For petrol engines, the use of un-
leaded fuel is compulsory.

The fi ller neck is narrower, admitting
unleaded petrol nozzles only.


Fuel supply cut-off

Your vehicle is equipped with a safety
device which cuts off the fuel supply in
the event of a collision.

5
VISIBILITY
96

Switching off the lighting when
switching off the ignition
When the ignition is switched off,
all of the lamps switch off immedi-
ately, except for the dipped beam
headlamps if automatic guide-
me-home lighting is activated.
In some weather conditions (e.g.
low temperature or humidity),
the presence of misting on the
internal surface of the glass of
the headlamps and rear lamps
is normal; it disappears after the
lamps have been on for a few
minutes.
Daytime running lamps

Daytime lighting, compulsory in certain
countries, which comes on automati-
cally when the engine is started making
the vehicle more visible to other users.
Manual guide-me-home lighting
Temporarily keeping the dipped beam
headlamps on after the vehicle's igni-
tion has been switched off makes the
driver's exit easier when the light is poor.

Switching on


)
With the ignition off, "fl ash" the
headlamps using the lighting stalk.

)
A further "headlamp fl ash" switches
the function off.


Switching off

The manual guide-me-home lighting
switches off automatically after a set time.



This function is assured:


- in countries where it is imposed by
regulations,
by illumination of the dipped beam
headlamps with the sidelamps and
number plate lamps; this function
cannot be deactivated.

- for other countries where it is pro-
vided,
by the use of dedicated lamps; this
function can be activated or deac-
tivated via the vehicle confi guration
menu.


The instruments and controls (instru-
ment panel, multifunction screen, air
conditioning control panel, ...) are not
illuminated, except in night mode with
manual or automatic illumination of
headlamps.

Switching on the lighting
when switching on the ignition
To reactivate the lighting control stalk, turn the ring A
to position "0"
- lighting off, then to the position of
your choice.
If the lighting is switched on manually
after switching off the ignition, there is
an audible signal when a front door
is opened to warn the driver that they
have forgotten to switch off the vehi-
cle's lighting, with the ignition off.
They switch off automatically after a
period which depends on the state
of charge of the battery (entry to en-
ergy economy mode).

5
102
Automatic rain sensitive
windscreen wipers
The windscreen wipers operate automat-
ically, without any action on the part of
the driver, if rain is detected (sensor be-
hind the rear view mirror), adapting their
speed to the intensity of the rainfall.
Briefl y push stalk A
downwards.

The instruction is confi rmed by
a wiping cycle, accompanied by
illumination of this warning lamp
in the instrument panel and an activation
message.


Switching on

Switching off
Operating fault
If an automatic rain sensitive wiper mal-
function occurs, the wipers will operate
in intermittent mode.
Contact a CITROËN dealer or a quali-
fi ed workshop.
Do not cover the rain sensor,
linked with the sunshine sensor
and located in the centre of the
windscreen behind the rear view
mirror.
Switch off the automatic rain
sensitive wipers when using an
automatic car wash.
In winter, it is advisable to wait
until the windscreen is completely
clear of ice before activating the
automatic rain sensitive wipers.

The automatic rain sensitive
windscreen wipers must be re-
activated if the ignition has been
off for more than one minute.
Briefl y push stalk A
downwards
again.
The instruction is confi rmed by
this warning lamp going off in
the instrument panel and/or the display
of a deactivation message.
Windscreen and headlamp
wash
On vehicle fi tted with headlamp wash-
ers, the low level of this fl uid is indicated
by gauge in the reservoir fi ller neck un-
der the bonnet.
Checking and topping up this fl uid can
only be done when stationary with the
engine off.
The driver should check the level of this
fl uid regularly, particularly during winter.
Refer to "Checks - § Screenwash/head-
lamp wash level" for the procedure on
checking the level.


Low screenwash/headlamp wash
level

)
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a fi xed period.
The headlamp washers only operate
when the dipped beam headlamps
are on
.